Видео

This one will spin a 48" blade for 21" cutting depth. They have others that will spin a 60" maybe a 66"

Better have a health bank account.

www.husqvarnacp.com/us/machines/wall-saws/

You are right. What do I have about 100K views? 🤦🏻‍♂️

@@balrock01 i’m sorry if it sounded like I hurt your feelings I’m just trying to make a point that a lot of people who post videos claiming their toy is to be possessed and the company should be held accountable for things like that it just makes me kind of angry because the majority of the times people miss hear things so it sounds like it’s saying something evil when in reality it’s not

It was more of a comedy. I had to listen to it over and over and then either Google it or someone told me what it said. Never heard of xray fish so it didn't even remotely register what it was saying. I have few followers and my snow blower video has the most. Don't really post anything for like or views. It's all good. Have a wonderful year!

Why would I do that? So I can strip a layer of the matrix away. You can't switch rotation on a hydraulic saw. If I'm making a vertical cut I'll switch rotation so I'm not throwing in the air for my convenience but other than there is no real reason to stop the saw go into the control box and reverse rotation.

@@balrock01 oh dam. My bad. for some reason I thought it was electric. Our wall saw guy left so I just been learning. I just realized I can reverse the way the blade spins.

@@rootsnculture no worries. Don't reverse direction once you establish unless you need to. That is electric saw but I used hydraulic for 15 years and just had to eat it. It's awesome to switch direction of blade to control slurry direction..ie left side especially flush cutting

@@balrock01 so if I'm spinning the blade one direction dont change the direction on the way back?

@@rootsnculture correct. Check your blank it will give a rotation on it. Only change rotation of necessary. I have alot of other videos. How long you been using Husqy WS system

Great for corners

Only gets 15 3/4 deep. Still need Hydraulic

@@balrock01 damn. Guess I'll have to use a modified bracket for a wire saw

Small roto hammer drill bit center of core at 45° angle and pull out

@@balrock01 awesome man thank you

Your a brain dead idiot. Husqvarna says 8" max which this is not and I can tell you it's good for much more than an 8" bit. Stupid comment

Wait till it releases from to much pressure and wraps your babybut around the column with the cord.....seen it happen to knowitall derboys too many times.....you will learn the hardway😂😂😂😂

I still have them but it's too cold for them. They also did not hold up well, cracked all along the front around ankle level. Very disappointed for pricey bpots.

yeah I remember you got them from a buddy of yours. You should look into those dunlop thermo purofort boots I recommended. They will hold up well in your work environment and they are good down to really low temperatures and will keep your feet warm. Let me know what you think.

They basically are dunlop boots www.bekina-boots.com/en/boots/industry

Before you say something like this maybe you should ask what firmware revision i am using? Because your statement does not seem accurate unless the husqvarna rep and mechanic are lying to me as the dynamics have changed with the revision.

Electric cord?? It's 80v battery no cord needed. There is a movable chute. Not sure what you have.

They are kirkland brand pants. Soaked and covered in concrete slurry.

It's a containment pit and i compromised it. Tomorrow it will be all gone

LOOKED?

Mountainview Ranch I need half high socks otherwise they rub my legs raw and i don't like my pants tucked in as they fall around my ankles which is also not comfortable. Otherwise they are awesome

Yeah I always wear my jeans over my rubber boots too. Don't have any issues with them rubbing my legs though. Show us a close up of the boots in your next video.