Видео

On my E scooter I get up the arrow display 14 but it does not beep and the accelerator works fine I was wondering if perhaps it was break when I try to hack it to do 30 kph it failed someone suggested to me that it could be error code coming from the break an as a result of that I was unable to get it to go faster is this property the problem or can anyone enlighten me please

not superglue

It worked for me. The con is it is too hard to put the cable inside, so I leave it outside.

Where to buy an xiaomi m2 pro motor can someone please tell me 😅

Whats the max temperature and equivalent amps running through the controller board ?

You missed the most important thing, ie how do you get to the motor once scews removed 😮

I saw the video and got frustrated and checked the comments and a few people said that they punched or throwed it. I hit the throttle a few times and its back to normal😂

can we use aftermarket lcds for the xiaomi pro 1 with proper wiring will it work?

mo o. mo a

Hi mate were did you get this kit from i have been looking and only can find the conversion kit but dont look like yours with the adapters thanks

I have a zipper x1 was ridding along and it just stopped still getting power lights etc any ideas can’t find fuses or reset switch

You're a genius, mate! Thank you!

Most annoying shit on the electric scooter hate it

Please what’s the bumper bit near the disk called mine came out of place both of them it fell off

Xiomi eror 15 plssss

you are putting the tire back on on from the wrong side. It is much easier from the opposite side of the valve

Still waiting for the answers guys?😁

how does the scooter track the speed its going

How did you go about mounting the rear wheel at the front? Mine wont actually line up or bolt in

I just started shaking my scooter and it worked again👍👍

Always problems with these scooter next time i buy one its from Audi jeep or something else NO CHINA iam sick of these errors

How did you reverse the rotation of the motor???????

Update, 4x sturdy teaspoons. My hands. The mrs' hands and my big toe. All wrestling in the kitchen floor.

I got mine off with kitchen spoons. Now to try get it back on with them 😂😂

our old xiaomi M365 sold as a Denver came with rear wheel drive, and with electric and disc brake all in the back, frame is steel not aluminium, and it has been working as a champ. now it needs a battery uppgrade, and i have been looking at controllers, maybe giving my kid a few km\t more, i have been looking for a 25 km\h controller, but all are 27-28 or more, the law say max 20 km\h here, and 5 more is over but not mutch, 10 becomes a problem and is a 50% gain in speed if stopped by the police. is there a adjustable controller that can be set and locked by me.

I buy pro 2 but the wire is red and black

how do you have those much scooters

Do you sell the parts? As a disabled e-cyclist I want to put 2 E9s in parallel, fit a seat and modify the controller with 1 throttle. I'm OK with all the electronics: I will change to me e-bike controllers if needed.

Pro 1 more powerful and technically better than pro2

It’s cool but maybe need to change the way of the tire, on rain it would slip too much👍🏻 very good job!

The Xaomi Pro 2 is the worse electric scooter I have ever owned. Constant problems. I am on my second scooter. I constantly get flat ties, the read fender and light fell off, Error 14 and error 39 on two different model. Sell it and buy something else....

Great idea! Did you ever think of throwing on one of those monorim rear suspension kits and the Rwd. Even make the two wheels 10 inch

Hello mate what size are the screws for the rear wheel mount?

That step at 7:00 looked so easy. It took me over 4 hours to get the friggin' wheel back on. Definitely invest in some long levers for that step or get ready for major frustration. This pro 2 tire change has been the worst ever.

You just needed to adjust the piston by adjusting the 5mm bolt on the inside of the calliper. Make sure you unluck the 2.5mm locking grub screw at the rear of the calliper first.

hello sir, what size of the crew nut that use you?

i just started googling how to fix the error 14 and i saw all these vids and got pissed off, hit the whole skooter on the wall and boom. fixed.

Just a comment about the motor wires. You should not need to cut the wires to get them through the nut/washer, at least this has been my experience for all the times I have threaded nuts/bearings on. It may involve pulling the wires through in a particular sequence and you may need to release/remove the wires from the connector housing and then reinserting them back into the housing once rethreaded through all the places they need to go. First Thing: Take a picture of the wires/connectors so you can easily put them back to the correct position. I like to take several pictures of stuff I disassemble, regardless of what it is... Its fast, easy, costs nothing and can really save you from incorrectly reassembling, looking like an idiot and having to search esoteric web sites inorder to reassewmble...and on occasion legal proof for times when individuals mess with and break things and try to blame others. The order I do is as follows. 1. Take the boots off the motor phase wires... hopefully they are the clear ones that are loose enough to pull off (common on xiaomi and clones) 2. Pull each wire through one at a time, you will need to wiggle each one through, as you do you will get more room to work the next wire through. 3. Work the 5 wire JST connector through... I have to turn the nut over the connector as its a tight fit, but the connector easily goes through with no damage. Note: If connector is to wide, you can easily release each wire from the connector by gently prying up the plastic tab and pulling each wire back.... be sure to know their correct position for when you reinsert them. (refer to picture comment above). Note: Only as a last resort cut the wires... even them, consider removing just the ends and soldering them back on afterward. Splicing wires can be a source to failure or poor performance in the future. Spices need to be soldered and sealed given the harsh environment of heat/moisture/vibration of a scooter. Poorly connected wires will be a source of elecrtical resistence which will heat, loss of current flow and worst case a short.... not to mention splicing shortens the wire. Perhaps its the electrical engineer in me, perhaps its the mechanic in me...but both sides hate seeing unnecessary and often poorly done splices wrapped with falling off electrical tape. ...and another thing...dielectrtic grease is the friend of electrical connectors, particularily when they may be of different metal types and corrosiion prone... ....self righteous dad type rant, not really a rant ends ... 🙂

Another video to help me get my son's xiamo rear wheel on thks!! It's been a nightmare so far with that bloody wheel.😩😭😭

Your rear tire is in wrong direction at 5:10

seems a common fault , good thing its pretty easy to fix, baught a new throttle off of amazon for £10 installed with some help from this video in terms of screw point locations, and no more error 14, i also had it where there was no error but the motor wouldnt spin, changing the throttle also fixed this - -- thnx

I already changed the accelerator for a new one but it still gives error 14. do you know what the problem is? If you can help I would be grateful. Thanks

I ordered a pro 2 from amazon and when it arrived I noticed it had the red cable the same as the pro1 but the box says pro 2 and when you search for it on the mi app it shows that it's a pro 2 as well 🤔 any ideas why I have a pro 2 with red cables?

Where did you buy rear wheel spacers?

Thanks for the video where can I get the nuts and spacers kit for rwd swap

𝕡𝐫ｏ𝕄ｏ𝔰𝓶 😈

I spent 4+ hours trying to put the tire back on with regular bike tools and failed. I bought the tools this guy uses, and (with the help of someone) I finally managed to put the tire back on! In the process I unfortunately created a hole in the chamber, so here I am going for round 3.

hi mate i have a aovo pro and it does 20 mph but the frame snapped when i was on it lastnight cut a long storie short i have another scooter called a anlen 250 w motor and i want to put my aovo pro 350 w motor on it because the anlan with the 250 only does 20 kph if i put my 350w in it what do i need to change just the motor or do i have to put the bar,s on aswell off the 20 mph scooter the aovo because there the same scooters just different name can you help mate

motor mmoooaaaa . 😃

And here i am trying to do this shit with a knife and my bare hands... wish me luck.