Видео

Excelente

How about the original remote? Is it still working after that? Thanks.

Try putting a short extension on your rachet next time, 10x faster

Using grease helps catch the metal shavings.

What year a model is your rogue in this video?

Does anyone know if it’s hard to change the oil pan in this car ??

This was horrible in so many ways, but at least bullets are still coming out of the barrel, and seems like it is enough for most people.

😊

The new key is blank or programmed? Have you a ebay link to buy it please? I buyed any key with pcb and blank chip. But I don't work. Thanks

Wanting to do something to save money is understandable, but safety has to come first, it MUST be done correctly. This is an excellent way of how NOT to do it. Concentricity between the OD and the bore is always off. Not taking the metal down to the proper max od before threading will never give suitable results. The stress that you are excreting on the muzzle can totally screw up the accuracy. To long of a thread and it might not seat the device properly. No relief cut for the threads?. Taking a file to the crown without dressing it correctly? People can be seriously injured by bad backyard hack jobs.

What did you do or change the button release. Mines seems stuck

Do you know what you’re doing.try using a lathe

Tried this and the Gold today. I'm going with the Gold but the silver is a really good gun.

As a gunsmith machinist this is a no go do not do this the threads need to be single point threaded in a lathe

Sometimes it’s not about the money, it’s doing it yourself. 😊

I'm assuming you are a regular shooter so how many rounds do you think you did? Were they mostly trap/skeet loads, #8 low brass perhaps

I have a 2011 Honda Accord . I programmed the key and it opens the doors but when I turn the ignition the car starts then turns off. The car does not stay on

Just bought a new to me 2017 with 96k miles. Do I need to change the filters as well?

How many miles per gallon do you get off this motor?

Gas or inertia?

I'll never understand why people half ass their fluid change on the transmission, there is a filter that needs to b changed under the pan

Twice I had to change my bushing

I can’t believe he did that

Why you change the timing? Your motor run rought?

I've watched so many times and I can not get the top plug off to save my life.

Does it matter which side washer is up or down on bolt?

By far the most detailed and clear video I’ve seen, thank you for this

Isn’t there a filter to change?. On my old Mercedes you have to take the oil pan off to change the filter but nobody had done it in 15 years on my car! The date on the filter was the same age as the car!! Changing the oil in the Merc transmission made a big difference 😊. Only asking because I might change oil in my daughter’s Rogue.

Awesome video man! Well explained. Have you done transmission oil/ filter change for this generation of Pathfinder.

Could you tell me what prop is on your boat. My boat was a rental so they limited the engine and prop only run at 35 mph. Know the carburetor isn't open all the way. I believe I need a 12.75 21p or 19p depending on the performance I want from it. Any input?

Awesome job.

Thanks

Spray the rag…… not the car….

Don’t use a card!!!!! They are super sharp and will scratch the lacquer!

An annular cutter would save alot of time ! Filing is a bugger.........

Professional guys!

Mashalah. Good time fishing❤️

Just had one fail the exact same way.

With 60 plus years as a gunsmith, firearms manufacturer and machinist behind me, in my opinion this is NOT a safe way to thread a barrel for a sound suppressor, flash suppressor or muzzle brake. There is no way that the barrel ends up perfectly round and with the external diameter perfectly concentric with the axis of the bore when you reduce its diameter by hand filing. Also, it would be tough to get the threads started square to the bore with a die even if the barrel were turned perfectly round and concentric, without the use of a tight-fitting pilot in the bore. Baffle strikes or strikes on the brake or flash suppressor would damage parts and potentially harm the shooter or bystander. Send it to a gunsmith and have it threaded on a lathe or use a freely rotating pilot in an annular cutter, to reduce the diameter and have it end up close to concentric with the bore, followed by a threaded pilot for the die to cut the external threads. The lathe, with an independent four jaw chuck, and a closely fitted plug in the bore to dial the axis of the bore into perfect concentricity with the axis of the lathe, then turn down the outside diameter, start the threads with a single point tool in the lathe, then finish them with the die if you want to, that's the best way to do this, but filing it down, not a chance, I have repaired numerous rifles over the years brought in by folks who tried to thread the muzzle end of the barrel in the manner described in the above video.

Im confused that, when I checked at Nissan service center they told me that no need to change oil for CVT and I run 200k without changing. What to do? There's no issue in gear changing. Having 2015 X-trail in Qatar.

This is the most real video i have seen. Thanks for the realism.

Lol....ok. from a former weapons mechanic with the 40th ARRS. Vietnam Era. If it works...ok whatever but it does save a handful of money. Thanks for the show.

Nice work man

Thank you for the nice unboxing video.

Mine doesn’t have a set screw? Is this an older model or have they changed it that you know of ?

Well done. While you're advancing your gun smithing skills others will hate. Dont let the ones bother you, that cant do it them selfs. Its like working on a car some people rather pay to get it possibly done right. Than just learning how to fix it and doing it for them selfs, for 3/4s the price😂.

Has anyone tried to siphon out the cvt fluid on a drain and refill? Instead of removing transmission bolt underneath the vehicle

Where do you get the insulation from? And what’s it called please?

Looks like he also worked on his shotgun and shot a hole in his corner post

It has a 28 inch barrel