Видео

Had mine for a couple months. Buy extra sheer pins! Also keep an eye on the impeller. Seems to be wearing really fast since it’s plastic. Not a good design! I do start mine at lower rpm but still sheers them.

Nice

lol, loved the flash back to the PC and it's all closed :D

That's awesome. well done.

Awesome review Gary!

Damn that's a lot of leaves!

I had to switch back to mulch blades on my TKV20. Kept clogging and think the high lift was throwing too much at the boot. Also cut back on the discharge of leaves out of the front right of deck. Only happens now when it's getting full. Good review though. The plastic top and the hose is a better setup.

Interesting, but I took a piece of coat hanger wire, bent one end to make a handle and it works fine. A whole lot less complicated.

Maybe small silicone vacuum caps on the zerk fittings would also work

Love the video and good information. I’m going to go and do some research as well but can you post what you found for the tipping limits or what you have the app set up for. I know it will be vary based on the setup of the 1025r but just looking for a base to start with. Thank you.

Did you pay for this app? I have a John deere 1025r with a cab it's very tipsy

I spent an hour looking for that app, and I had no luck

Love this, Gary. Never thought of it but definitely going to get it. What did you do to get the tip points? Assuming they’re published from Deere somewhere.

1023e dash flasher works, but not on the rop. Tail lights work, but no flasher lights

Why do you need the clips? Can't you just use the PVC caps alone?

When I saw this a few weeks ago, I thought that might be a little too much of a hassle ….. until I had to work on my tractor. This past week I had to work on the tractor with the loader still attached & sure enough, I had to lean over the loader rails. My belt buckle was at the same elevation as the grease fittings and I got grease all over the front of my shorts and tee shirt. As soon as I saw what I did, I thought of this video. Thanks for posting!

That is a great idea ...

Another quality video by my man Gary. Straight to the point. Thanks for sharing!

Nice job man I will be doing this

Do you know if the new kit is stock on the '24 tractors?

I have just been using the key to push it in.

Cool deal, thanks for sharing.

Why is your 4x4 lever in a different position from my 1025r.

I just ordered that parts to do my 2025R Nice Job

I can't take another project. Make this a kit and take my money!

Good 👍🏻 tip ❤ thanks 🙏🏻

Looking to do this mod when I pick up my 1025 but can't seem to find a filter and housing with the sensor. Do you have a link or part number you bought?

Great write up, I just finished the install on my 2025r,which is similar to the 1025R but…. The 2025R, although it’s very very similar to the 1025R, has a fender brace bar that runs directly under the place where the switch would be mounted on the 1025R. I had to fab up a mount using a 1” piece of square tube that I fed thru the bar and mounted it to the base, then mounted the switch to the bottom of the square tube. Took me longer than it normally would take but doable if you want it. And I had to buy one of the “Jesus” clips from the dealer because my tractor ate one of them somewhere in the frame😀 Thanks for the write up👍

The tip about removing the side panel to get at the rods was worth $1,000,000! It's a bear without that information.

Heeyy.. I found this on youtube ;)

Nice! 👍👍

Nice video. My 4WD likes to drop out from time to time so this will give me a "Heads up"

Nice job! 👍👍

Awesome work! Just ordered the parts.

Alright, where do you find that vinyl boot in menards?

This ain’t bad.

Good idea you join the Facebook group and you’re in charge of that one. I like new ideas like that

Very nice easy to follow, perfect timing I was ready to change my filter . Thank you👍👍

Nice, I really like the clean look. Next mod should be the loader tube. Covered storage tube.👍👍

Nice improvement at a reasonable cost & off the shelf parts.

Great Video. Headed to pickup my parts

Thanx Buddy appreciate the feedback. I keep filter in the toolbox in case I need to change on the fly.Best thing I think is no tools needed to change.

Very nice job with the upgrade. I recently did a simpler upgrade, but yours looks a bit easier to service at each filter change interval, Very nice.

facebook.com/share/egg7arweJagpguPM/?mibextid=K35XfP