Видео

Excellent information 👏

how did you locate the studs in the wall before you drilled into the drywall?

👍🏻❤️👍🏻❤️👍🏻❤️👍🏻❤️👍🏻❤️👍🏻❤️

❤️👍🏻❤️👍🏻❤️👍🏻❤️👍🏻❤️👍🏻❤️👍🏻

With you on this one. Got a leak to repair im guessing tomorrow or mon. Found leak on one of kitchen windows. Guess thats one good thing about a storm and rain hitting at correct angle. Cant wait for it to stop now though. Leaks found now storm can piss off 😂

Does this actually work?

Spot on 👌

Ledge

thats so clever , thanks mate !

oh thats a good idea mate very handy

Great video that outlines the basic steps of doing a ceiling, thank you. However, based on my experience if you're hanging more than a couple of sheets seriously consider getting a drywall lift. The work will go faster, it will be more accurate, you'll suffer less fatigue at the end of the day and if you have any pre-existing injuries, you're less likely to re-injure yourself. Also with a lift, your more likely to bring a sheet down to fine tune the fit rather than force the sheet in place breaking a corner or edge. Used lifts are readily available and when you're done, can usually be sold for what you paid for it so your cost is zero. Thanks for sharing. Cheers!

I’m adding a hive thermostat to this exact boiler The one I’m adding it to has this mt10 timer do I need to remove this or can I just flick the switch too off so it doesn’t interfere with the hive

How much water to a bag of bonding

👍🏻🙏❤️👍🏻🙏❤️👍🏻🙏

That's not happening with me. 🙁

Hi can I have different thermostat fitted on Same boiler wireless one ? What will happen to the mt10

I am just about to renovate my bedroom after the ceiling began to drop in my old house. So I am watching every video I can for tips. Thank you.

Thankyou so much you saved us. This is the only video i found which helped me alot😊

Did you put more self leveller on top of the first lot or is this just an over lap of the video where you put self leveller down? Cheers

Lucky i got no snow

Shouldn't mix your tools with cum rags, lesson learned.

Ive no key in mine. Is there any way of raising the pressure without a key??

❤️🙏👍🏻❤️🙏👍🏻❤️🙏👍🏻

just put it on the board

That totals £285. They robbed you.

USA....😂😂😂

Think i would be aswell bud. Lovely job.

How do you top up if you haven't got a green lever

Didn't want to show us the finished cut close up??, 🤔😂

Could be stuck if it hadn't been used for a long time. Try to spray a bit of WD40 on it that should help.

I have this combi but the green level wont pull down, any ideas why? like its locked it place

Ive got the same two valves on mine why do i have two?

make videoo more longer ❤

nicd ❤

Great handy work

Gareth

Thanks very much! How can i adjust the water pressure? It's below the optimal range.

Why don’t you put silicon around the mixer cover plates? Maybe it can also prevent water slipping behind the wall?

our mum does 2

Stupid Homescapes ad

Youve explained and demostated perfect thanks pal

It’s nice to see such care being taken in public toilets. Hats off to you!

I recommend deleting this video you used the worst song in the world (also I like the bath room)

Thank you!

Is brushing this dirt enough ? I have seen people painting it with bitumin and throwing sand on it before rendering to block it coming through

Swap blue grit for yellow pregrit. You'll love it

Mines showing zero but the hot water and heating is working fine, do i try to top it up still??

And whach out for that bridging 👍

Don't suggest floating in bonding matey. It tends to rip as its a much more corse material. You would be better with hardwall as it is desinde for floating high suction backrounds 👍.

Had to remove this crap in a 1930s house