Видео

this is literally a ecoboost 2.3 engine

Купил ниссан....сам с ним это самое

Styrofoam would have been even quicker.

Sounds like the villagers in mine craft 😂😂😂😂

Great work!

Excelente trabalho um dos melhores trabalho de torno que eu já pude ver Parabéns pelo seu trabalho abraço amigo fica com Deus

Motar hp?

Молодец!

👍👍👍👍👍🤝🤝🤝🤝🤝

How long did it take you guy?

What axle did you use for the passenger side? I cannot find the right part for my 2013 police interceptor sedan witch a Ford Taurus and every part store O’Reillys AutoZone advanced all their websites say they have the right axle but when we take this one off and compare it to theirs them line up with the bracket that you have to unscrew the 213 mm bolts Honestly, I’m not sure what to do at this point because I can’t find the right. Axle nowhere

You deserve 10 out of 10 just for cutting the bar with a Hacksaw well done bud 😁😁🤘🤘

Nice job, what temperature did you get it to blow at the vent?

How do you know how much to add or are you just guessing?🤔

Good work except for refrigerant filling..cylinder should be in upright position and qas quantity by weight not by suction presure reading..

W video

Its vpc?

Why is it seems like its a wooden?

Да ну нахуй

Dude, you’re right there. Just replace it lol

Very hard work to clean this

How much was this job in this country?

tons of work

Olá amigo que maravilha de projeto trabalhando super, parabéns!!! Boa sorte sempre!!!

that's a clever idea reusing the chrome bar from the car shocks, never would have thought of it. However i would have used a rear 10 stud axle from a truck for the chuck. there's a hole down the middle so that you can feed things through and the tapered bearings have low runout.

Самый тупой метод, или пример как не нужно работать. Особенно резка ручной ножовкой по всей длине заготовки, а потом сверлил как из пулемета (без масла кстати) где можно было ножовкой резать и при этом имелась болгарка! Это как закрутить лампу вместе с табуреткой.

Excellent work Guys, excellent teamwork and attention to details!

Hello buddy, I just saw the video. But where is the next episode? Please continue the project and share us you experience

هل انت في السعودية

نفس نوع سيارتي ٢٠١٤ كانت الثلاجة تالفة وغيرتها بالاصلي كامل ١١٨٠ ريال وتركيبها ١٥٠٠ريال مكلف جدا الفلبينين جيدين وعندهم امانة بالعمل🎉

👌👌👍👍👍

ruclips.net/channel/UC6Y8sXa9ikoAxS6c7mDsjlQ

Dba need niya ng oil ano maganda diskarte niyan kasi wala ng oil lubrication?

Pwedi airhorn compressor for

Судя по количеству времени затраченному на изделие, человек явно хрен без соли не доедает. Вопрос, зачем левой рукой правое ухо чесать.

💯💯💯💯💯👌👍🤝

Vibration et jeux par tout fixé dabord la tête motrice +chariot pour une bonne execution.final .

Лютий пздц! Той верстат смикається, стрибае, а один єдиний різец- напайка не ламается. Буду в нього замовляти.

ราคาคับ

Just the thought of cutting that much metal with a hacksaw makes my hands and wrists swell with pain. Very cool work!

Hi ... are you in Saudi Arabia?😊

Incredible work!!

Tis ford no rench

Thanks , very good 👌

A trick I have seen mechanics use for flatterning cylinder heads is to glue the sand paper to a sheet of glass to get a flatter surface.

Hola!! El material que utilizas es PVC?? Gracias

Verygood Nice you ar exceptionnelle thankyou veremoth

عمل شاق لكن النتيجة جيدة

Is that plastic?