Видео

You give good tips like putting the threads to keep the gasket in place. Do you think its mandatory to use gasket sealer, is it in the manual or can I also do it without? Any ideas why the gasket failed in the first place?

just bought into eero mesh 6e router at amazon

Just tried to do it on a 40 year-old Penta 2002. Was able to slide the gauge in the intake valves but not the exhaust valves. They must get looser from wear and tear or do they get tighter?

is it still available? location? thanks

What if no fuel comes up to the vent screw? Even if fuel comes to the manual pump.

I sent a message I would like to come see the boat if it is still for sale

Thabks ror reply.I have one built in 1986 abd it has the lecer. I got fed up with the suction feui pump failing due to pooriy fitting couplingsi,I converted it to an electric feul pump. Now runs kike a dream with a beat you can dance to.

Valves can be set cold. You should be turning the engine over on the crank shaft nut as you are putting strain and wear on the fan belt and alternator bearing. There is also a decompression lever which allows you to turn the engine more easily.

Is starlink just allowed 1 router? I connect start link with eth adaptor to switch,then from switch to router access point.but when i try to connect my second router it cannot connect,unstable..i try to connect to my DVR,the result same. My question is starlink just allowed one router access point?

Thanks for your effort. I will do this on my 2003 tomorrow (if I dare). I guess I will need a new gasket.

There is a lever on the engine at the front which you turn that releases the compression so you can turn over engine easily while doing tappets. Would not advise using alternator nut as it could cause belt slippage and also putting strain on the belt.

A diesel mechanic showed me how to change my fuel filter. He had me fill the new filter with fresh diesel (NOT the fuel from the old filter) to avoid having to pump the fuel pump so many times. I only had to pump it about a couple dozen or so times before the bleed valve stopped blowing bubbles. Here, you had to pump it at least 350 times and bubbles still came out.

great vid. Could you, by putting the starlink in bypass mode, disable the wifi and only use the hardwired setup like yours - no wifi enabled?

I'm changing the fuel filter on my VP 2002 today, this is exactly what I needed, thanks! The Volvo filters are hard to find, unless you want to ship them from Sweden. The current filter, a NAPA 3358, was on the engine when I bought the boat in 2023. I am replacing it with a WIX 33358 fuel filter.

Thanks for sharing this tutorial. A 2002 owner..

2003 would have been a better choice for 32s5

5:15 5:17

4:42

Did you have to do anything with the wires?

Subscribed! Clear and concise, thanks for that. The only problem I have is that I can't seem to find that belt, as well as other parts for my fresh-water cooled Volvo Penta 2002. Even when I go to a reputable dealer that services Volvo Penta they say that they can't find parts either, including the 966906 belt. Some have suggested that I take the existing belt to a NAPA auto parts dealer and see if I can find an equivalent.

Do you have a link to the switch you are using? What is the best switch to use? Thanks.

Excellent video! Thanks for sharing 😊

Oh that's too bad you missed the tunnel🙁.

Thank you !

I'm trying to get my PC to connect to the starlink's wifi. My cell phone is connected to it. Do I need to make any adjustments to my PC?

Nicely done Wendell, thank you. : )

Would you be able to show how you ran your raw water from the water pump to your anti shiphon and then back into the heat exchanger? I assume that's where the black raw water hose is headed...

Hello Wendell. Once set up, how often should the calibration be checked. If you have a power cut and it's raining and your gauge tips 10 times say, will those 10 tips be recorded? Just asking. Jim.

Dope

Can you connect an extender to the ethernet switch?

can you help me on my home pc with starlink?

i wonder if i can put another router on that aux port,. my house have alot of walls that makes wifi weak in bedrooms so im planing to put another router in the hallway thru that aux port ,. will that works?

ditch the starlink router and get yourself some mesh routers, also plug that starlink cable directly into the switch and you'll get greater speeds!

Awesome! Finally someone can explain something USEFUL in about a minute. You're a champion!

You forgot to replace the seal on the threaded shaft!

thanks

I'm looking to do the same swap. I'm hesitant to drill the hole for the new unit without knowing it'll work. I don't see how 8 wires were required and now only 6 are; to do the same thing. I found a Canadian seller that still has the Link 20; so I could do a one for one swap, but their site isn't working. I'm hoping they'll call and I can order over the phone.