Видео

Great video bro. I have been struggling with a 07 CRF450R. Your video was the solution to my problem. Great job. Thanks!

how do you remove the shift drum

Hey man, thanks for the video. Quick question. Where did you find the rebuild kit with all the gaskets and stuff?

If you find a supply of the centre body gasket o ring for the road race version of the FCR please post a comment.

Quality video, thanks for the tutorial

Great video

Safety torx.

awesome video so thorough and you put it together slowly.

Good stuff mate. 👍

This was a really good piece of content. Transmissions are always scary for everyone, you took some of the fright away for some I'm sure.....@stanforadventure

wedge tool, and you can easy remove old bearing, without any damage.

Great vid. Thanks!

How do you install it back to the bike?

My gears are rounded a bit but 5th slips like mad so over 1000 bucks usd later i will have all new gears from yamaha

Great little vid! Do you have a link to the bearing race removal kit that you used in the video? Thanks!

If I send you my carb and pay you would you rebuild it? Clayton Carb Builds! Its got a nice ring!

Great video! Thanks for that short and clear explanation.

LOVE YOUR IN DEPTH VIDEO! I NOTICE THAT YOU "AIR CUT OFF DIAPHRAGM/COVER" IS MISSING! EVEN IN MY 2006 OWNERS WORKSHOP MANUAL... IT IS MISSING! IS IT DELIBERATE?

😂

Thank you for making a video about this. i have been struggling with my 08 YZ 250f for some time now with a bad bog of idle, replaced ALL the seals/gaskets/orings/accelerator pump in the whole carb except the mid body since almost no one talked about that, everyone just yelled that it was the accelerator pump which already was replaced. After having the carb apart for the 5th time in a year(what a pain it is to remove on this bike), it finally runs correctly after replacing the mid body kit!

Not to bag on your method of madness But... the Use of an Impact screw driver on Carb Slide seems Strange to say the least. Hey U gotta Improvise right?

Great video. I've got the 2005 wr450 runs great but pops a lot on decel I'm at a 170 Main and 48 pilot should I go up on the pilot a few sizes? Thank you

or you can do buy the tool for lke 30 bucks lol

Hey man, I just rebuilt the carb on my 2004 yz250f. The bike was running at the end of last season but I decided to rebuild the carb this spring cuz I knew it needed to be done. Only reason it ran last season was because I had a family friend clean the carb and he recommended it be rebuilt. Anyways I’ve rebuilt the carb and now replaced the fuel petcock but I can’t seem to get the bike tuned right to idle well. Just wants to die on me unless I keep it alive with the throttle. I could really use some advice as this is the first bike I’ve ever had. Would rather not have to wait to get it into a shop and pay big bucks for what I truly believe is just a tuning issue. Please let me know what you think I’d really appreciate it!!!

Thanks so much for the tutorial, I'm fixing a yz250f on my channel, and I couldn't figure out how to do this. Also my name's clayton too 😅

excellent vid!

i butchered my carb trying to adjust the accelerator jet because someone before me put it in to where it shoots the stream facing the airbox. luckily i found one on ebay. great video man thanks for posting!

FANTASTIC how-to between this and the first vid on the tear down! I feel super confident now. I’m very mechanically inclined but carbs can still be intimidating. Especially slightly more complicated ones like these. What do you recommend for new vent line? Also, do the all balls rebuild kits include the 3 o-rings for the fuel inlet fitting where the fuel supply line hooks up? Thanks Also liked and subbed ;)

This guy has some of the best illustrations on repairing that i have come across. Helped me out makes it simple ect

Thanks M8, much appreciated. Going to do this this week, never to late for an old dog to learn new tricks.

What fluid do you use in your Ultrasonic cleaner for carbs? And how long do you run it for?

Answer me this if anyone knows but these carbs look all the same on these 450 bike from one brand of bike to another. Are they all the same brand?

Great video! Did my first carb rebuild with it. Thank you for your time and energy.

Clayto buen canal lo recomiendo..

Great video, my mid-body o-rings were Silly Puddy due to sitting.

can i send you my carburetor?

Fantastic

Really tempted to do this

saved the day big guy

Great video brother

At 14.58 that little tube shooting out gas, is it replaceable, because mines broken, or is it part of the carb body.

Thanks for the video man I watch a couple and still had some parts left over and was like wtf.. you were very detailed so I got it all back together

All after market junk. Yamaha made Japan parts are expensive for a reason.

WHATS UP EVERYBODY ITS CLAYTONMOTOS...YER BOI

Really great info. Thanks for putting this together.

Great video buddy! Thanks for sharing!!!!

It would be very helpful if you actually showed the camera what parts you are dropping into the bottom of carb before u screw them in, so we can see which goes where. I am grateful for you making this video, had a guy come over that claimed he could rebuild my carb and took it all apart without me being present and failed. Now I'm trying to piece together what he took apart. 😮‍💨

you aren't supposed to use a hammer on the seal driver. you just slide the driver down the tube into the seal and it acts as a hammer itself.

DUDE!!! Really impressive carb video, great job thank you

Rebuilt my YZ426 carb and thought I was done, bike still runs like crap and won't kick start, adjusting valves and buying this kit because the mid carb was so tarnished when I took it back out. Thanks for the vid.