Видео

im curious, can't you just swap the bellhousing for a 4L60E 5.7L one and not need all the spacing?

Great work, I'm inspired for sure, just subbed.

This is the exact build I want to do on my 3rd gen can’t wait to see the progress and how it turns out, love the vids keep it up 💪

How does the motor and transmission hold up to the 37s ? Is she super slow ?

For a replacement washer fluid tank I used a universal one for sxs's it fits between the rad support and air box the the original pump pops right in just lose the rear squirter

Did you ever build this out?

Were you on stock gearing with 37s?

at the bare minimum you need sliders

There any update on this build? Found this series and its kinda puahed me to keep my 3rd gen and put some work into it.

love the 4runner content. Get a new one, we need more

want to make the same look for my 99 chevy 2500 it would look so tough 🙂

Have you fixed this up yet? I found your first video because I was searching for Tacoma Rubicon footage then started watching your 4Runner stuff. Great content man!

You have a mad skills my braddah

The short answer is no, a stock Tacoma won't make it without legendary lines and luck. This area is the gatekeeper (namesake implied). There would have been plenty of progress after that, along with bypasses. Would be cool to see a website where they note their vehicle details including tire-size, heighth/lift, and obstacles surpassed. This was a cool video, glad there was no serious damage to the vehicle.

No spotter, no sliders, just you, your dog and a come along. You’re a beast bro.

Where the frick you be at???

Good job brother! Thanks for picking up the left behind trash.

Valiant effort

Would a setup like this fit in the 73 model?

Thank you for the info! Got a broody Orpington right now needing a bath.

Memories 😅

A for effort. The other Tacoma bros with lift and 35/ should try like you.

if u went with a locker in the rear what did u go with? starting my build watching these videos lol

Why in the hell are all the sbc turbo builds no intercooled lol

What gear ratio did you change too to pull those big A tires

enjoyed the camshaft story & music

Got ya a poon wagon. You can also use those exhaust studs to mount the knock sensors on the outside of the heads, so they last longer plus you wouldn't have to pull the intake off to replace them.

Do the drum brakes still stop it? I'd like to do the low AC & that water pump & a few other things on my swapped '65 C10. If you was closer I'd pay you to work on mine, but by your CA tags your too far away

Hey did you ever figure out a solution for the Dust shield? I just did this swap but can't find a dust shielf that works

Size and type of tubing???

Do you have a link to the throttle cable you used?

A bit late here but YT only just served this up. I believe an experienced driver in the AEV or even ZR2 Colorado could readily make it to the bowl. The others...not so sure.

Did your taco have a little locking rear diff?

What bumper and winch do you have on that puppy.

Question...a drawing of what you did..in sections...who be very nice....showing all parts , diagram..on wiring each part up......

Nice work. How you get the ac compressor wired into the ls pcm and cooling fans? Please advise

2 inch Body left Would have been fairly cheap and helped out the situation a lot, I would still do it It would look a hell of a lot better too

I like the way you got the trans on the jack

excellent and dirty job but you need 4 hands for this I want to do the same on my 2000 4runner

Awesome build. Awesome video.

Clean work

Hi! Was it flux core or gas mig?

DOC OFF-ROAD for skids!! Go check'em out!

So clean. I am currently struggling with a wiring nightmare on my LS swap

Man that was awesome. I need some fire pit therapy soon.

Hi! I’m doing a 1972 K10 LS swap What do I do with the gauge cluster? Is it possible to have a working speedometer and do the sell gauge clusters for this purpose? Thank you, Bill

hey would you be willing to bend up a kitand ship? ill pay

Ho much 700r4 transmission $?

What did you use for those turn signals?! Sweet build!

Sniper has a tps mounted on side you can tap into. Let me kno when you work on a project. I can sale you some parts you don't need