Видео

thank you

hindi na kelangan ung gate at internal connected na un.

the book when company bought that printer together with manual. now if you need that book you call ikaje nearest your place . where your location?

happened to me sometimes, just reset and re start . some motor hard to start then okay after

@@tmelectricaltutorials2851 sir just I reset so many time but again coming same alarm

Glad it was helpful!

im sorry amigo, me no understand what u say amigo.

thank you 🙏

thank you 🙏

whats 2030 fault showing ? you tried everything did you drain the ink ang flush running for 3 days unblocking ?

i found already that fault is deviation power failure. you need to un plug and re start printer then keep running unblocking head . if again do it again gonna come off after

hi kabayan Mukang nag aayus karin ng printer na imaje ah . dami mong matutunan sa inupload kung video .

ngagyon lang kita masagot kadarating ko lang galing pinas.

@@tmelectricaltutorials2851 yup meon kmi nyan madami ung iba alam q n rin pero may mga mahirap ayusin khit n mga nagpalit n ng parts

sometime jet head not clean, you need to clean with methelkethon and while cleaning run the jet unblocking head.

⁠​⁠@@tmelectricaltutorials2851not familiar with methelkethon is it the additive?

you dont see up and down ??? watch again u will see

thank you

i counter that sometimes the fualt is jet not detected. run unblocking head bout 5 to 10 minute sometimes disappear. fix . if still same problem run breakof point adjustment. keep tryiing that way.

how about always drop phase detection error lods? ill try to the EV Maintenance but can’t lunch the procedure. What do u think is the problem?

i dont know the size , but only one size and 5 needles belongs to this sewing machine.

the reading on the screen doesn’t rich set point if termocouple problem.

Thank you! 😃

hindi sa you tube lang panoorin video ko, ung mga ksama ko sa work swerte nila

saan ka po sir sa canada ka po ba?

trace mo kung saan papunta ung input.baka ung tatlo para sa main contactor yung dalawa para sa control transformer step down .

@@tmelectricaltutorials2851 salamat master👍 cge trace ko .

walang problema mg tanong ka lang . saan lugar kaba?

sure but im here in the philippines 🇵🇭 for vacation right now .

Thank you very much!

oo ung tatlong heater delta connection. pero grounded sang heater kaya disconnect ko sang heater. pag shutdown nila ang line saka palitan ng bagong heater unit pra mapalitan ng heater.

Thanks

baka single phase check primary side at mo sa load side ng contactor up down reverse baka single phase.

habang press mo up botton check mo load power supply primary at load side ng contactor. ganun din sa down

Hindi naman po. Chenik ko nang tester yong volts kapag may load na bumababa po nagiging 206 na pero pag walang load hindi po bumababa sakto naman ang boltahi mataas nga po umaabot nang 231 volts. 220 kasi yong supply

Tinanggal namin yong motor inactual sa load side nang contactor gumagana po yong motor hindi nag low voltage. Pero pag kinabet na yong motor ayaw po gumana umu-ugong lang at nag lolow voltage.

thats is original sounds paster Rpm because of fan blade to much pressure.

sometime thats happend. re start ang keep running unblocking head while cleaning with solotion .

Maybe for how long should the unblocking take?

search Omron twin timer i uploaded already video same control circuit diagram . thanks

you can connect terminal 6 to terminal to terminal 7 for normall open contact.

I have try joining terminal 6 to terminal 7 using push button n.o contact ,and when pre set total counter achieve ...I push the push button but still cannot reset the pre set total counter ?

semilar connentiion instead pressure switch use timer on delay to start M2 if energized M2 and second timer for M3 its up to you how much you want time to start motor. but connection is same.

@@tmelectricaltutorials2851 Thank you

thank u 🙏

salamat idol