- Видео 10
- Просмотров 3 712
Smitty
Добавлен 31 дек 2022
professional goon
ABS Repair on Ninja 400 - Front Wheel Rotation Sensor Wire
Front Wheel Rotation Sensor Wire Repair for Ninja 400
Connector and wire I used: www.aliexpress.us/item/3256803940660559.html?spm=a2g0o.order_detail.order_detail_item.3.3c8ff19cG45u7q&aff_fsk=_Dk5AJwn&src=connexityUS&aff_platform=aff_feeds&aff_short_key=_Dk5AJwn&dp=17272169371840165092717831196008005&cn=316730&cv=10c7b93085dcea51dede51fce3db2eee&gatewayAdapt=glo2usa4itemAdapt
Make sure to buy the “Set With Wires”. This is the one with the connector.
How to read ABS light code and erase existing codes: ruclips.net/video/uoxEI1rdGSc/видео.htmlsi=NrQMBM5quQk9QtmI
Connector and wire I used: www.aliexpress.us/item/3256803940660559.html?spm=a2g0o.order_detail.order_detail_item.3.3c8ff19cG45u7q&aff_fsk=_Dk5AJwn&src=connexityUS&aff_platform=aff_feeds&aff_short_key=_Dk5AJwn&dp=17272169371840165092717831196008005&cn=316730&cv=10c7b93085dcea51dede51fce3db2eee&gatewayAdapt=glo2usa4itemAdapt
Make sure to buy the “Set With Wires”. This is the one with the connector.
How to read ABS light code and erase existing codes: ruclips.net/video/uoxEI1rdGSc/видео.htmlsi=NrQMBM5quQk9QtmI
Просмотров: 49
Видео
Read and Clear ABS Codes on Ninja 400
Просмотров 10915 дней назад
How to read and clear ABS codes on Ninja 400
Drain Gas Tank On 1999-2006 GM Trucks
Просмотров 132Месяц назад
Drain/ Siphon gas tank on 1999-2006 Silverado, Sierra, Tahoe, Suburban, Yukon, Escalade, GMT800. Bypass the “anti theft” valve on gm gas tanks.
Blessing of the Bikes 2024 - Cape Cod
Просмотров 1786 месяцев назад
Blue Knights 46th annual Blessing of the Bikes at West Dennis Beach, Cape Cod.
1993-2014 KLX250/KLX300 Valve Inspection and Valve Adjustment
Просмотров 2,4 тыс.7 месяцев назад
Unfortunately Kawasaki doesn't have a online version of this service manual so i'm not able to link the valve clearance sheet. use www.dirtcloud.com/valveshim/ to help calculate the correct shim using the clearance standards I gave in this video. Model Coverage: 1993-1996 Kawasaki KLX250D (Offroad) 1993-1996 Kawasaki KLX250E (Street) 1994-1995 Kawasaki KLX250G (Street) 1999-2008 Kawasaki KLX250...
Ninja 400 front turn signal bulb removal/ replacement
Просмотров 35410 месяцев назад
The bulb is a Osram 5009 which I believe is found on multiple other Kawasaki turn signals so this works for some bikes other than the 400. Made the video since I couldn’t figure out how to remove it and there were no video online for it. Hope this helps
Rear Axle Bumper Stop Replacement for 99-06 Silverados and Sierras
Просмотров 64Год назад
This replacement will work on all 99-06 Silverados and Sierras along with the 2007 classic models. Part #: 523-049, 15712438
Summer Trail Ride on the KLX230R
Просмотров 383Год назад
Back after a months break from trail riding. Using a new angle for the GoPro by placing it under the visor on my helmet and shooting in superview to make the video wider
Blessing of the Bikes - Cape Cod 2023
Просмотров 68Год назад
May 7th 2023 Blessing of the bikes in west Dennis beach
Last Ride of 2022 | Klx230r
Просмотров 39Год назад
I enjoyed your video. Getting ready to do the valves on my KLX250s. Think I would have left the intake clearance alone because the gap only gets greater as you put more miles on it? That's just me anyway. Thanks again!
@@Kawboy13 thank you! If the clearance is right on the edge of spec then I would go and adjust it so it’s slightly in the middle, that way whether it tightens or loosens over time you will be fine. Good luck you got this!
Thank You brothuh! I’ve never done a valve check/adjustment for the shin type and this made things much less intimidating.
@@trustmedood glad I could help! You got this!
Holy Water in a Home Depot bucket. They say....He was a carpenter!
Is there available service manual on internet
@@diin5938 there are a lot of service manuals online for this bike, unfortunately you have to pay for them. Mine was the “Cyclepedia” which is available online too.
Best video I've seen for this procedure , thanks Man !
@@danielcarroll5667 Thank you, Glad I could help!
Ended the video with someone else crashing 😂🙈 looks like a good place to ride and the klx seemed right at home
I crash too much, gotta show other people doing it every now and then so I don’t look as bad 😅
Same procedure for a 2022 KLX 300 I’d assume, yes?
The owners manual I was using stated it was for 1997-2008 KLX300’s. They should be relatively similar but yours is fuel injected unlike the 2007 in this video. I would double check the specifications for your bike as they may not being similar because of that.
Can we do LED bulbs on these?
Yes absolutely! I didn’t show it in the video but I actually was taking these out so I can replace them with LED’s. If you do chose to get LED’s you will need a relay so they don’t blink super fast. I bought the one from TST industries and it works great.
@@Smitty196 what bulbs did you put in??? I tried picking some up from oreillys and they were garbage! They were even less bright than my stock bulbs so I took em back...
@@jordanpayne8144 I used VEHICODE 5009 RY10W 12093 Amber Yellow on Amazon
Hey man i appreciate the video. keep it up👌
1:30 poor bike
Ayyyyy love to see it gents. Cannot wait to get up there from ct.
Thanks for posting.... 😇 Regardless of the weather, it was still an awesome day.... 👍
Always so much fun, already excited for next year!
Awesome looking machines, thanks for sharing looks like it was a great turnout as always.
Was looking for you this year but didn’t spot you sadly 😅 was hoping to park next to you again haha.
Thank you 😊
Great job.currently have to do this on my 2007 klx250s and not looking forward to it.but this is a great example,thanks for sharing
Great video thanks for posting
was on the yellow bike next to you