I'm having problem with the tuning, i can hear the RPM on Idle changing all the time, what can be wrong? Maybe i should adjust the HSN so it will give more fuel??? Cause RMP are increasing, then i open the Idle screw and after few sec's engine goes off
Very nice Video. Love the Lunch Boxes and own one ;) My hint: get oil schocks! (example: tamiya 50520), runs a lot smoother and it's no problem to run an 540J Motor (little faster, check out my Vids)
@sharpshooter383 I have not united brushless ｗith TXT. I think that I only have to take it from BEC if the receiver power supply is taken. By the way, my TXT is 14.4V brushmota specification . The amplifier of the system was used of brushmota E550 E-zilla.
Thank you for the comment. I'm sorry that the answer is delayed. It is an engine setting. It is very difficult. Because it changes in the temperature and the fuel. How if a variety of challenging? It worries about whether transmit accurately because it is not good at English.
Tja. Har du kollat så att det har kommit in soppa i motorn. Hade samma problem själv. Skruvade in nålen helt, sen skruva jag ut den 2,5 varv. Low-speed rörde jag aldrig. För att få in soppa i motorn, satt jag fingret på avgasrörets mynning och drog i snöret. (utna glödnyckel i :) )
Hey! i saw you video with you Kyosho DBX, i have the same model. but i realy don´t got it to run yet =( So... can you be my hero and tell me hoy many turns you have unscrew´d the High-Speed Needle from closed position? And the same with the Low-speed screw, I will be greatfull with all my heart if you check and tell me PS: excuse my english, im from sweden / Sebastian
hello, i hope you can read english, i enjoy rc alot. i think its a great contribution that the east has brought to the world. i was hoping you could tell me why you had a face mask on over your mouth? was it the time of the bird flu scare ??
リコイルを引き切るとよくこうなるみたいですね 大抵の場合あ、戻らないと思ったら引っ張るのをやめてフライホイールを手で回せば直りますよ！ どうやら原因はリコイルのあのボルトみたいなベアリングなんですよね…
small but powerful
I'm having problem with the tuning, i can hear the RPM on Idle changing all the time, what can be wrong? Maybe i should adjust the HSN so it will give more fuel??? Cause RMP are increasing, then i open the Idle screw and after few sec's engine goes off
Very nice Video. Love the Lunch Boxes and own one ;) My hint: get oil schocks! (example: tamiya 50520), runs a lot smoother and it's no problem to run an 540J Motor (little faster, check out my Vids)
エンジンのほうターボでもはいってるんですか? 高い音がしたんですが? ちがいますか?
stiuped idiot!!! you pull the pullstrat if its cinde of lawnmower
@Basse92 try 2 and a half turn unsrewed..
好 good.
@sharpshooter383 I have not united brushless ｗith TXT. I think that I only have to take it from BEC if the receiver power supply is taken. By the way, my TXT is 14.4V brushmota specification . The amplifier of the system was used of brushmota E550 E-zilla.
0:57あるある～！！ σ(ﾟ∀ﾟ ｵﾚ!! の友達よくそれでリコイル壊してバラシ常連作業になってるｗ 今じゃひも切れたからプルノブ外してキーホルダーによくついてる巻いてあるだけの鉄リングつけて引いてるｗ
You guys gotta warm the engins right up and set the carb up correctly, they should go much faster, and not stall :)
ありがとう御座いました。
ポテンシャルはｄｂｘ 走破性はｍｔ2ですかね・・・ 個人的見解ですけど・・
Thank you for the comment. The lunchbox is happy.
ずっと気になっていたんですけど、ｍｔ２とｄｂｘってどっちの方が速いんですか？
It becomes uncontrollable if running fast.
It is invulnerability.
Thank you.
Because it is 1/10 ･･･
It is a 4WD・・・
このコ－スＧＰ＆ＥＰ混走なんです・・・
Grasshopper is a great car. I think so.
Thank you for the comment. I'm sorry that the answer is delayed. It is an engine setting. It is very difficult. Because it changes in the temperature and the fuel. How if a variety of challenging? It worries about whether transmit accurately because it is not good at English.
Tja. Har du kollat så att det har kommit in soppa i motorn. Hade samma problem själv. Skruvade in nålen helt, sen skruva jag ut den 2,5 varv. Low-speed rörde jag aldrig. För att få in soppa i motorn, satt jag fingret på avgasrörets mynning och drog i snöret. (utna glödnyckel i :) )
LOL EASE UP ON HE PULL START!
omg my tamiya grasshopper goes faster
Hey! i saw you video with you Kyosho DBX, i have the same model. but i realy don´t got it to run yet =( So... can you be my hero and tell me hoy many turns you have unscrew´d the High-Speed Needle from closed position? And the same with the Low-speed screw, I will be greatfull with all my heart if you check and tell me PS: excuse my english, im from sweden / Sebastian
well done with tha pullstart
very funny
Thank you. motor？ It is standard. 『MABUCHI 540 motor』
nice jump at the end of the movie. What motor do you use in that car
pulled too far...
Thank you.
Thank you for the comment. It was not possible to go well in the fuel adjustment at this time.
うう お気持ちお察しします・・・ 私もリコイルバラシは通常作業となっております・・・
昨日、シェイクダウンでびょ～んってなりました（笑） 早速リコイルをばらす羽目に。。。
You should gas when the nose of the car is going down in the air. And break if the nose goes up. Just a tip...otherwise...great vid! :-)
Thank you for the comment. Mask? It is my lifestyle of this season.
hello, i hope you can read english, i enjoy rc alot. i think its a great contribution that the east has brought to the world. i was hoping you could tell me why you had a face mask on over your mouth? was it the time of the bird flu scare ??
ええ、目がついていきません・・・・年かな・・