Видео

👍

techcraftandhacks.in/smart-dustbin/

Unfortunately, no link. I took it from old toy car.

Thanks

Thank you for commenting. Next part will be uploaded soon which will look better.

👍

@Genio_soy 👍

The Last Goodbye - Telecasted

👍

👍

@@feelincrispy7053 👍

I need to buy another one because I found that the motor speed is not optimum. I tried with different power, up to 9 volt battery. Still it's not working.

For code for various projects please visit techcraftandhacks.in

The motor driver shield should be placed on top of the Arduino Uno, with the motor driver's pins aligning to the Arduino's headers. The Arduino Uno will sit on top of the shield, and the two will be electrically connected through the pin headers. If you need to connect the motor driver to the Arduino differently (perhaps for a custom setup), you would need to use jumper wires or other methods to connect the pins properly.

With i2c module working with LCD becomes easy.

When I purchased the price was 110rs +delivery charges. Price varies depending on location and seller.

@@OP_ARYAN_PRO_2468 Yes, we can. Video is for beginners who are learning Arduino.

Yes.. it's very simple project.

@@TechCraftAndHacks2 can u give link of all?

@@kennethmamaril4978 I keep it attached to the device but I always make sure that device is switched off. For example, if it is connected with a remote car then I make sure it is switched Off. In case the wire is naked then I cover it with good quality tape. It protects from a short circuit.

@@ghousemohiuddin3073 Yes..

@TechCraftAndHacks2 can you tell yes what?

@ghousemohiuddin3073 If you are using similar charging cable then light will change when full charged.

🤣🤣

Exactly bro

But maybe he's trying to learn with this circuit

Ya for some beginners it's a difficult part...

It's for beginners who started learning Arduino.

Relay was used...JQC3F-05VDC-C.

voice over ke saath video upload hoga...very soon.

Thank you bhai pata to chalega kya product use hua hai kaise conaction karne hai aur item kaha se milenge thank you bhai​@@TechCraftAndHacks2

Beginners prefer Arduino...But ESP 32 is a great choice for projects.

Aap mera shorts videos dekh sakte ho...mai need bases pe purchase karta hoon. Upcoming Videos on: ESP32 ESP 32 Cam

// Define pin numbers const int moistureSensorPin = 2; // Digital pin for soil moisture sensor const int pumpPin = 8; // Relay module pin to control the pump void setup() { Serial.begin(9600); // Start the serial communication pinMode(pumpPin, OUTPUT); // Set the pump pin as output digitalWrite(pumpPin, LOW); // Ensure the pump is off initially pinMode(moistureSensorPin, INPUT); // Set the moisture sensor pin as input } void loop() { int moistureLevel = digitalRead(moistureSensorPin); // Read soil moisture Serial.print("Moisture Level: "); Serial.println(moistureLevel == HIGH ? "Wet" : "Dry"); // Print moisture status if (moistureLevel == LOW) { // LOW indicates dry soil (check your sensor specs) // If moisture level is low, turn on the pump Serial.println("Soil is dry. Activating pump..."); digitalWrite(pumpPin, HIGH); // Activate the pump delay(5000); // Water for 5 seconds (adjust as needed) digitalWrite(pumpPin, LOW); // Turn off the pump Serial.println("Pump deactivated."); } else { Serial.println("Soil is moist. No action needed."); } delay(10000); // Wait for 10 seconds before the next reading }

// Define pin numbers const int moistureSensorPin = 2; // Digital pin for soil moisture sensor const int pumpPin = 8; // Relay module pin to control the pump void setup() { Serial.begin(9600); // Start the serial communication pinMode(pumpPin, OUTPUT); // Set the pump pin as output digitalWrite(pumpPin, LOW); // Ensure the pump is off initially pinMode(moistureSensorPin, INPUT); // Set the moisture sensor pin as input } void loop() { int moistureLevel = digitalRead(moistureSensorPin); // Read soil moisture Serial.print("Moisture Level: "); Serial.println(moistureLevel == HIGH ? "Wet" : "Dry"); // Print moisture status if (moistureLevel == LOW) { // LOW indicates dry soil (check your sensor specs) // If moisture level is low, turn on the pump Serial.println("Soil is dry. Activating pump..."); digitalWrite(pumpPin, HIGH); // Activate the pump delay(5000); // Water for 5 seconds (adjust as needed) digitalWrite(pumpPin, LOW); // Turn off the pump Serial.println("Pump deactivated."); } else { Serial.println("Soil is moist. No action needed."); } delay(10000); // Wait for 10 seconds before the next reading }

It's in video.

😀😀 Mistake in video Editing. I didn't validate before uploading.

110 Rs... price may vary depending on location and merchant.

110 Rs... price may vary depending on location.

Yes.

Didn't get it.

Soil Water

Thanks

Thanks

Thanks

Red Wire is +ve.... connect to the +ve terminal of battery. Black wire is -ve.... connect to the -negative terminal of battery.

@@TechCraftAndHacks2 how to increase range please🙏

This one is 27Mh transmitter and receiver and truth is you cannot increase more than that.

It was purchased from Amazon.