Видео

That a good Leonard thanx for watching

@@leonardarola braap pipe soon as I know it's working

@edle7663 I understand, I too have my reservations about investing on an expensive pipe until I know the engine is properly.

​@@leonardarola totally agree with you on that no point if it's not working correctly you won't get the affect of the exhaust pipe

Thanx man they're always watching me build something they are to small to use yet so I am gonna build them something they can and we will ride together

Thanks 👍

It's a must on motorized bike build gotta have good stopping power

@leonardarola this is my first 4stroke bike don't know how it will run but it was a fun build (welding project)

Check it out I redone the spendle better should be a lot better now stay tuned for more videos on the goped

@leonardarola this is how it was done years ago I'm recenter it so it's better now check out future videos on this build

@@frosthoe thanks for that I am gonna try it out and I have a silencer for it I don't run all the time but I'ma try what you said and see the results

Thanks 😊

Thanks

Would that be stronger if it was one piece do you think it's going to break

I took it all apart cleaned up everything the reed needed to be replaced

Everything welded on it so no movement but the chain tensioner I'ma weld on stay tuned man I'm working on it now

Always was a 2stroke guy still is but this was free so I'm building it going to need to buy pedal extenders x2

But with a new wheel an sprocket adapter for sure problem solved but that to easy 😊

Getting it ready for a engine setup

Building blocks

@@edle7663 nice

Right on I mad a video trying to explain to a subscriber how to do case vents I have done everything I was doing to it thanx tho

I'm doing a 98cc roller rockers and this is valuable information

​@@jasonburque glad I could help what ratio rockers are you goin with

@edle7663 i have no doubt that engine runs it clearly seems like you know what your doing. So are you saying I can run lines like that with the check valve still installed? Did you buy this as a catch can kit or fabricate it all up yourself? I'll watch any 196cc video you put out as I'm tearing my bt200x down right now. Hopefully the hisun motor has bearings installed cause I rode hard before deciding to tear down and have seen videos where engines like these are missing stuff sometimes. Last question I think I have an oil leak and you mentioned the case seal did that leak out the bottom primarily? Thank you

​@@Stealthhayes93 I made it they sale them I just like to hand make stuff an save money so I used brass fittings drill it 3/8 and force them in didn't even tapp it out so I may catch a lil oil around the fittings but my oil leak was a blown seal behind the flywheel thata a block someone had it on Facebook marketplace for 10$ I had all the parts cause I had a blown up 196 off a ct200u that was done last year all of that was done to make it look cool

​@@Stealthhayes93you can run it with the check valve still in the cover just don't remove it an put them further up then I did I'll make a video of it to show you cause I have another valve cover but to fix the problem of removing the covers check valve I put a one way check valve on the tube coming out the cover I have put a bolt in the tube pretty much blocking any oil are air from coming out but the engine need to breathe so it blew out the old raggedy seal so I put the one out of my blown motor witch was still good and bought a inline one way check valve

​@@Stealthhayes93 oil leak could be 3 the side cover gasket but that's not likely unless it was opened up and didn't replace the gasket most likely a bad seal so I would take off the pullstart an look for oil or moisture also use a light and look behind the flywheel see if the seal is out or if the flywheel is oily it should be dry everything would get oil on it with seal leak as the clutch and flywheel will fling oil over your hole engine once it sits for awhile oil will drip down leaving a puddle underneath also double check the oil drain bolts tight hope that helps I'll make a video soon an explain it better to

@edle7663 ill check your video. Still working on removing the engine from the frame and while I can't see where the oil is coming from i have oil everywhere under the engine. I'm trying to learn as much as possible before I disassemble the motor. Have you tried any other weight of valve spring than 22lbs?

@stealthhayes93 I could do a running video of it no prob let me know

Right on man I love your builds as well

More to come stay tuned

It would be a help to me I can't figure this thing out I have down everything I know it still act up no power

That's the plan!

I having the same problem still clean carb I don't understand why it ain't running right valve is set .004 in .005 ex I still get same results I am kinda loosing hope

Yes it will

I'ma grab a in line check valve should fix the problem

@@edle7663 good call. Will watch.

​@@leonardarolasure enough man thanks for the feedback also thanks for watching good day buddy

Thanks 👍

For sure thank for watching an also for the feed back ima put a seal in it and a check valve should fix it fun build tho stay tuned

Why u ain't like the video homie 🤔

​@@SpACeCruizeR2o3thanx my guy hopefully you got your engine right 😊

@edle7663 i did broski had to get the dremel out its perfect tho good looks 💪🏼💯

I managed to get it out but I think my problem is blocked tube were a check valve should be I won't run it again without putting one on it

I think it built pressure up and had no way to release but threw the seal

@@edle7663 ohh man!

It's been fun got to many projects though need to finish them up so I can move on to what's next

Will do

Thanks for watching!

Thanx

@@edle7663 get sorted?

It's possible I'm gonna weld up a pipe cause the stock exhaust would hit the red vent tube

I am leaning towards the pwk carb will fix the problem what you thinking

@edle7663 PWK rules. I like them very much.

​@@leonardarolathinking that would get it to run right I did port the head awhile ago and it was a 28mm on it so that might do it thanx

@edle7663 Thanks, those are racing engines; there will be a delay on new videos and shorts, I'm suspended under copyright strike untill November. For background music... Go figure.

Them is some bad motors your working on I'm going to stay tuned in good work

Awesome, thank you for watching quick question do I talk loud enough you can hear me in the videos

@edle7663 yes, we can hear you fine.

I soak it allday it's clean now it's time to build it back up

Yeah it's got rust at the top of the cylinder bore it's in vinegar now to break up the rust