Видео

Cheers Liam best video on drumb adjusting I've seen

For the benefit of anyone who couldn't get the lever assembly to seat properly have a look at the smaller of the two clips on the new part. I noticed that it wasn't finished properly in the manufacturing process and there was no gap at the bottom clip that's necessary for that clip to seat properly. This was the case with the right hand handle assembly, but the new left hand one was done correctly. A junior hacksaw and a small drill fixed the problem. Hope that helps someone.

Hvala ti do neba.Spasao si me 😁

Just replaced that plastic housing part and my gearstick still feels sloppy 😢

Really helpful. Thanks La

cheers mate just got my grand daughter a fiesta and both are bust ( but last owner bought the latches and left them in the car) now going to try and do it

This is too much

Good morning Am good understand this will be no problem for m.o.t. passed?

Is there not a self adjuster on these

Nice one. Exactly the info I was after.

Not copper grease, thats anti seize, you need silicone grease for lubrication thats safe for plastic and rubber 😉

Good man👍

I like your accent

its the same on a 2006 ford fusion,took me two hours its a job to see where in goes,but im 78 years old.

Thanks mate will try this tommorow 👊

thanks fella,was going to oder a new switch (£116 ),but only cost £9 odd thanks again

Need to find which is the hot side before putting the fuse adapter in.

You absolute legend, thanks

Thanks for the vid. Easy and straightforward.

My pin doesn't want to release and push down even after removing the bolt

Amazing thank you

Thanks, this helped a lot.

what about the relay box ??

I have the same problem as you but in my case the steering lock is inserted and the key does not turn, I can change it by simply drilling the pin that you move by turning the key or I have to tamper with something else too

I was finding it tricky to get a new window in my car as bought a replacement from scrappy. But thanks to this video i can do it now. Cheers, bud 👍

Hi great video I've been told you cant just replace the barrel because of the steering lock needs changing surely that's not true please help

Nice video. I adjusted my fiesta 2010 brakes way too loose and couldnt get the handbrake to hold. Overthightened the handlever and broke the cable. 😪I found this video after that

Thanks a ton mate! Probably saved me hours of tinkering!

Fantastic vid just done mine after it being broke for 6yrs

Tolles video. Gruß aus Deutschland ❤

great,I think I should manage :) Question: my cylinder, in a Renault Fluence , moves too freely, is that safety pin also holding the whole thing tight in place? when I sort of hold the cylinder steady/keep it tight in place with one finger, I seem to get the key out of the lock much more fluently. No restrictions then. Also: a little push to the key befor extracting it seems to make some difference.Starting etc is not my problem, just insert key and it then goes easily through all the moves, only hassle is to get the key out of the wobbly cylinder!

This worked well. Thank you 👍🏻

Nice one

highly useful. Thanks !

Best handbrake video I’ve found. The brakes on my 2013 Duster pretty much identical. Now working properly. Thanks.

Very helpful video. Nice close up shots of what you were doing helped me a lot. Thank you

Thanks

Wiring looked neat, but I'm surprised your tow hitch hasn't fallen off yet.

Great video had the same problem with my clio the barrel spring must have broken and would not return the key back to the neutral position when starting the car so had to do it manually.I went to a garage and got quoted €245 to replace it as they said it was a very difficult job,well now I can do it myself thanks to this video 😊

I wonder if the car still started after all that testing 😀

Great video Liam

Great vlog cheers. Sound level very low though.

Thanks man, saved me a lot of hassle

Could anyone help I was able to take off the handle but I just can’t fit the new handle on I try follow the vid exactly but the cable won’t clip in and the handle won’t go fully down

Could anyone help I was able to take off the handle but I just can’t fit the new handle on I try follow the vid exactly but the cable won’t clip in and the handle won’t go fully down

If this problem does not effect the m.o.t.I will not bother,thanks anyway.

Legend bro got me out of a jam

Brilliant work 😎😎

Nice!

Thanks a lot mate