Видео

Why are u using the (1-exp(-50*time)) factor? What is the influence?

Thank you for your great explanations and for this amazing list

Thanks for the tutorial, very helpful!

what is the master/slave boundary in the current version of ansys

How to simulate stray loss in maxwell Any vedio available sir

Hi. Thanks for the tutos! May i know this to calculate magnetic force? Does this the same process to calculate magnetic force for permanent magnets? Thanks

Hi thanks for the tutorial but im sorry but whats brad? Whats the meaning of the graph plot? Sorryy im quite loss

Whats brad? 😭

I cant load this vid why?

Sir thank u very much but quality of video and audio is bad....

Amazing video again Kamyar, thanks!

What I amazing video! Thanks 😁

Hey Kamyar, thanks for the videos. 😄 Do you know how to add an arbitrary time varying voltage source as excitation for Electric Transient simulation?

hi , kamyar, if you want to optimize structure according to the result of simplorer, what should you do?

Excellent video!!!!, I wish I had found this 8 hours ago 😵

very interesting i wish to keep more in touch with these tutorials they are so helpfully

Do you have any idea why my calculated DC resistance gets messed up when the bulk conductivity of the material becomes less than 1? If the conductivity is 1.01 S/m I get a resistance around 1.5k but when my conductivity of the material is set to .99S/m I get a resistance of aprox infinity. Any ideas?

Hi, i want to know the value of primary and secondary side leakage inductance. So, total leakage inductance is Lr = L11*(1-k^2). Then, how much primary side leakage inductance?

What's the meaning of this current, it's the peak of a sinusoidal or it's a DC value? I want to corelated the flux generated with the H, A/m. I'm trying to simulate an inductor with permanent magnet to compensate the DC current that I have one it.

Thank you very much🙏

Thank you

I'm trying to model a dual stator synchronous generator using this video but I have problems with excitations. I want to arrange those coils to be in three phases.

Thanks for the clear video. How can I make this external field varying in time? Just assign another variable within its definition? Thanks!

Hi, Thank you for making a great video. Could you please tell me why the capacitance value decreases in ANSYS MAXWELL when I add more than two plates?

Hi, Thank you for making a great video. Could you please tell me why the capacitance value decreases in ANSYS MAXWELL when I add more than two plates?

Hi, Thank you for making a great video. Could you please tell me why the capacitance value decreases in ANSYS MAXWELL when I add more than two plates?

Hi, I want to graph the self-resonance behaviour of an inductor. Which solution method should I use?

hi can you send again file link

thank you very much

thank you very much it was extremely helpful

in the external cicuit design we add 100ohm. is it the resistance of the copper? İf not what is the use of it? can we eliminate it?

Hello, this video is very helpful to me！Thank you very much, but i have a question. I wonder if Maxwell can simulate how to power on the transmitting coil and then get the current received by the receiving coil? For example, only the transmitting coil is excited in Maxwell-3D, because of the existence of mutual inductance, the receiving coil outputs the induced current. Can i obtain the induced current data through Maxwell?(such as use Maxwell circuit?)

I am using maxwell 16

Thank you for your video. Mr kamyar how can I add a thyristor to external cuircuit? I want to design an inverter fed induction motor. A full bridge inverter but there is no thyristor in components part

Hey mr. kamyar, I am unable to create four terminals of maxwell 3d WPT block when exporting to simplorer. Please help

Hi sir, only transient model can be used for co-simulation?

Hi Sir, When using Simplorer simulation, the coil current is the circuit current or excitation current. I do not understand this point?

Hi, what does the current value means in the excitation , sir? Is it a DC value or peak of a ac current?

Hey, I have a question, how analogous to this example can I create an impedance over distance graph?

Your great....your just a life saver. These series are very informative. You have just given me great insights on ways to move forward with my project. Thanks.

I’m searching a community of Ansys designers

Exact video for how to draw spiral coils. Thanks a lot for this video

How to plot impedance plot over distance?

this freaking saved me agha

Thank you, i have a question, what about Q-factor?

this is very useful for my students!

Hi Kamyar, What if their is a lot of parametric setup with different condition of current where one is fixed and one is swept? How to solution result will be shown?

Update this link

Badbakhtane in iran we can't sign up and download the file you mentioned in this video, is it's possible to put it somewhere we could download it?😢

Could I ask for a file of the B-H curves from the video?