Видео

You showed the pruning blade in the video. I could see that the brand is Milwaukee. Can you please tell which exact blade you used (including TPI)? Thanks

Hey buddy, how do you like your Navac since its been 3 yrs. I just found your video love it thanks for the full detail. My question is how long did it pull down since you are pulling the whole system. I'm looking to buy it any more info that you can give me would be appreciated.

i get inspired when i see people of colour in hvac

Impresive

How long cable ?

Zero-G hoses are a waste of $$. This cheap crap will spill water out from under the cheapo plastic collar. I just LOVE getting my shirt and pants wet whenever I use it. Cheap Chinese POS.

Where does the control wire at each room mounted unit go to? how does it know when to send coolant?

good review but i would do away with adding background music, it makes it harder for people to hear you talking.

Thanks great video!

Hey Jeff!! It has been a long time. I just bought one of these of FB and was looking for a video and there you are!!! Hi!!!

This software monitoring need activation code ?

Can't see what your doing,

Good stuff man

I got these but haven’t used them because they don’t have that lever switch on the side but ima take your word for it

I used to start those units up

What state are out of ?

You forgot to turn off the power of electric water heater at the service panel

Tôi đang tìm hiểu về thiết bị này và video của bạn giúp tôi đưa ra quyết định 🎉

The box says there is a star 15 and a star 20. Where are those? Mine doesn’t have them either

Put the link for the connections you have on it

Very helpful, thank you!

According to the National Electrical Code (NEC) ampacity tables, the minimum wire size for a 100 Amp circuit is: 3 AWG Copper. That 8 AWG wire is severely undersized and may overheat; and as such is a fire hazard. I believe they misunderstood the directions. Each breaker requires an 8 AWG wire since they are 40 Amp breakers. If they were wiring the hot water heater directly from the main service panel, 8 AWG wire would have been appropriate. However, they are using a subpanel which means it must safely carry the entire load of all three breakers. The breaker for the subpanel is under-sized for the application. The water heater is rated for 120 Amps and is being supplied by a 100 Amp breaker. This is much less of an issue than the wire size but should also be addressed. I hope they reconsider their installation and upgrade the devices to spec.

Thanks For The Advice 👍👍

Thanks a lot... now i have an idea how to make a DIY machine

The story of my life - due to how I hang curtains that end up hanging half way out of the wall. This time, I do have one stud to work with. Thanks for your video and now I'll see if I do a good job or make another big hold in my wall. 😅 Enoy you day!

Great review bud. Just purchased one and can't wait to put my hands on it !

Good video I just bought tools

Appreciate you.

What size is that wrench for the acetylene tank

That's a 26kw water heater. That's 13kw per leg. That's 2/3 the power of the whole house of that's even a 200 amp service.

So with the unit running. You can press P1 and P2 to cycle between incoming and manifold pressure? To see 2 separate readings? Not differential pressure

Had to subscribe great content

Be carefull of refrigerant leaks in a confined space... make sure you have it monitored and ventilated.

Great job 👏

Why are these boxes recessed? they should be flush to the drywall..

Whats the work life balance in controls? I know in HVAC and refrigeration it can be constant ...is there on call in controls or is it set hours

Thanks! Your video was helpful in making my decision to get one.

The MC is smart as hell / I had to grab a dictionary

what no satisflying door bell ring at the end? I want my money back! hehe thanks gonna test mine tomorrow

Nice! gotta change the battery on the smoke detector next

Thank you so much!! Great instructions, comprehensive, easy to understand and thorough.

Good tip regarding silicone with plastic plumbers putty with metal:) Good job!

Thank you sir, i actually was hired with no formal experience on a maintenance crew, my boss got me one of these since I don’t have one at the time. The whole crew was supportive and taught me a lot, I’ve been working for them now about 4-5 months and have grown a lot more confident working on my own. You mentioned briefly about the guy that didn’t work out who had never seen one of these before. I’d just like to say that any longhorns out there and you get a new guy on your team don’t be afraid to show em a thing or too and make ‘em feel welcome, they just might stay and surprise you. Always great video thanks fam!

Obviously u not a plumber u install this electric thankless without any safety u miss services valves and more important a safety relief. valve just in case system fail and cause a bad explosion 🥵

9 and 10 are called Robertson (square drive) number 1 and 2. Number 2 square head is often used for breaker screws snd also removing the panel. In woodworking the square #2 (robertson) is used for pocket hole screws primarily and are also widely used in Canada in deck screws. That's Canadas version of the USAs T25 torx head deck screws used in the USA. I got this 11 in 1 as part of a 22 piece kit with toolbag at my work (Lowe's) on clearance for a hell of a deal. $15 for the whole toolkit.

Can you use them for cutting torches?

Due to the un-understandable regional dialect, do yourself a favor and turn on "closed captioning" (CC) before watching this video. Other than that, this gentleman seems to know what he is doing. 👍

God bless you it’s late night revising my profile I was fortunate to start in construction and now transitioning out of service work

That's why they give you a lifetime warranty if you get a lemon take it back and they will give you one, I've used them for a long time no issues at all have one in both vans.. love the videos keep up the good work.

I just got one but does this have sound to it? I can’t seem to get the sound working