Видео

Thank you very much it was very helpful

thanks for sharing. i needed a no nonsense bandsaw tune up video. much appreciated!

Very useful. Thank you!!

I just bought some trouble a Delta 18” with two knobs for blade tracking. The manual is no help. It just says turn both knobs equal amounts.. Great! That’s real help full. Nothing about both clockwise or counterclockwise, or one clockwise and other counterclockwise. Or hints on turns to track the blade forward or backwards. Can anyone help haven’t found a video with two adjustments knobs?

Simply thanks! Great video, easy to follow along and understand.

Very good information!

Did I miss something or is his whole advice about tracking a blade oh just put it in the middle? This is kind of a nothing video

Great video. My blade sits perfect and as much as I spin it manually it stays bang on centre. However as soon as I run it on the motor the blade comes off after a second or so!

Where are you making adjustments?

Nice and simple. I have had guidance about the surface of the wheels being a bevel and that the gullies of the blade should be in clear air so just off centre? Is this true?

Thank you

thank you, sir!

I am having a heck of a time getting the bandsaw blade on my jet 14” JWBS-14sfx model bandsaw. I have literally tried everything to get the blade to stay in the middle. When pressure is applied while sawing the blade tracks to the rear of wheel. This causes the blade to loosen. When sawing stops the blade travels near to center again but not exactly in same place when started. I am using a Timberwolf 3/8 6tpi blade with a fine kerf. Saw unusable for a week now with approximately 3 hours total use since purchase last year. Any suggestions. This has been very frustrating to say the least for such a bragged about bandsaw.

Lol, I was gonna say, I'm a tool guy and I certainly don't have a micrometer. 😂

Subscribed. How about a video on how to upgrade a bandsaw? Like replacing solid side blocks with bearing guides/ I have a 14" Jet bandsaw i added a riser block to i would like to further improve. Replacing tyres this week.

Nice vid. What's the solution when the blade drifts to the right when trying to cut a straight line? The guiding bearings perfectly set, but still the blade drifts. Why? Thank you.

Thanks for sharing

Very clear and useful demonstration. Much appreciated.

Hi thank so much for this video, everything so well explained and presented, I am completely new to bandsaws, my first set up, I had followed the instructions on the suppliers video and had the saw running until yes the blade came off, I was able to get it sorted thanks to this video, also the tips for setting the bearings are fantastic more detailed than the suppliers, so hopefully I will get sawing and creating now. I was looking forward to watch the rest of the videos in the series, so I hope all is well. Take care Sam Ps I did subscribe 👍

Guy...great video and teaching ....thank you. Question on my Jet JWBS 14SFX when I set up with a 3/16 blade.....I track it in the middle of the tire by hand and also by turning it on.....and every thing is all good, but then in the middle of cutting out a bandsaw box the blade has completely come forward and slides right off the wheel. Any suggestions on what I'm doing wrong? or what the issue can be? Driving me nuts! My guides are all set up properly .....I'm thinking my tension is good. But still have that issue of the blade losing its tracking when cutting a pattern/bandsaw box.

But he never mentioned why the bandsaw blade came off in the first place or any solutions?

Very good Guy, I will now go and try your method on my new titan bandsaw. Look forward to see your next video, All the very best Glenn 👍

Thank you

At work we have a Jet almost like this one and no amount of tinkering it makes it cut straight: the blade invariably twist and start cutting to the right (we're cutting AL ) Quite frankly, those saws are very cheap looking and feeling, thin and wobbly . We also have an old 1970's Syderic band saw (french manufacturer ) and it cuts straight as a laser and requires no playing left and right with this or that gizmo. It's also mostly cast iron , weighs a proverbial ton and doesn't wobble. Much better tool.

By listening to him talk I get the sense this guy doesn’t know what he’s talking about or why he’s doing what he’s doing. Now that I’ve completed the video, I’m sure of it. Too many awkward pauses, very few close up shots, lack of using the proper terms and his skimming over certain subjects (details) and worst of all…no theory on why you’re doing what you’re supposed to do. And by the way, that was a dial indicator not a micrometer.

So long as my blade isn't drifting, it doesn't have to lay center in on the wheel? Mine lays further to the back.

I have a question for you about my craftsman 14" bandsaw. The saw is set up like you said, and it has made this sound since new. The wider the blade the worse the thump and louder the noise. It's a thump and wining sound. I have checked all the blade guides, nothing wrong with them or the blade. It doesn't matter what blade I put on the saw. It does get louder when trying to resaw a wider board. Do you have any ideas?

Great job Guy! It takes more talent to simplify things than to keep or make them complicated. You have done exactly that.

I just picked up an old wards bandsaw. the first thing I did was to clean and paint it up. I had taken the top wheel off before the blade was running true. now it drifts and comes off within a few turns. adjusting does not seem to help. the tires are cracked and worn they are on the way here along with a new blade. not wanting to wait on my new parts I went and tried to put the old blade back on. last time I had done anything with a bandsaw was around 10th grade and although I passed its been a long time and need a refresher on the use and maintenance of a band saw. I had ordered rubber tires that is what is on it now. the tires are 12 inches and the blade is 78 inches long. the old blade is about 1/4 wide and I ordered one that is Magnate M78T58T4 Meat Bandsaw Blade, 78" Long - 5/8" Width, 4 Tooth, 0.025" Thickness. I was not sure of the length at the time I ordered it looks to be 77 3/4 hopefully it will adjust to fit.

Great video! Very helpful! You explained this in such a way that my GREY HAIRED BRAIN UNDERSTANDS! THANK YOU

Very helpful. And I like your attitude that fixing the issue is easy. We live in a world of hype.

Great video! Thanks for posting!

Great video, Thank you !

Great tips

Thanks, Guy. I like the tape idea. I have the same saw and the quick tension arm is loose in the off position. Wheel seems out of position. Have you had this kind of problem?

This was super helpful, thanks!

When I start ripping into the wood the blade wants to turn why .

I’m still having problems with my wen 10 Inch tracking issues the rollers on the bottom are confusing for an old guy like me I really don’t know what to do ,it doesn’t track right hope you can help hopefully this old fart can figure out a way to send you pictures

wonderful video-thank you so much for taking your time to make the video

Very systematic process. Great.

Great video new subscriber thank you

I can’t keep my band saw blade running straight. I rocks back and forth. Not side to side. I’ve changed the blade and it’s still doing it. There’s no videos on RUclips on how to fix that issue.

I know this is different from the JET J8201K Metal/Wood bandsaw, but hopefully this helps. I’ve had issues with getting this thing good since getting it. Not enough info out there in it yet. Gonna try this though.

Guy the Tool Guy - Thank You for getting PopPop up and running!

Maybe simple but doesn't address the problem of the blade coming off the bottom wheel!

I have an old Craftsman band saw. It has about 3 degree drift - I adjusted the tracking on the blade and it is dead center. It did not solve the problem. I also adjusted the table. It helped but the table doesn't have enough adjustment to solve the problem.

Just bought this band saw (first one) and have watched several videos on how to set it up, tracking, etc. This video and explanation is the single best one I have seen. It really helps that you have good camera angles and close-ups of the saw blades as you explain what you are doing. Well done my friend! God bless!

Haha. You had me with that micrometer.

By far the best video. Simple easy no complicated crap. Thank you sir 🙏

This is about my 10th video on this subject and this was the best. no further videos needed. Thank you!