Видео

it is a little longer and the off set is a little different, so it will give you more camber and some neg toe, you will need a alignment after installing them, I wanted more camber because I track the car, plus the weight saving never hurts.

She is really enjoying it!

We are so glad to hear you have been following along, thank you for your well wishes

the wife got sick, and the ships doctor was not able to care for her so we had to leave the ship, to seek care in Nagasaki

This is travel insurance it is different from the cruise line coverage, its is something you can buy from a travel agent or on your own. the problem is currently no one wants to transport the wheelchair and her on the vent, but we have a lot of people working on it

you can get a tool that will pressurizes the cooling system, that you hunt down where the leak is, or you can bring the car to temp and see if you can find the leak, you can check the tubing for damage in the area of the leak,

with all the bracing and new coil overs, it is very stiff, great for tracking a bit hard for a daily driver,

thanks,

i put it on dry,

yes the leak was fixed with the new gasket

connect KDM tuner and see if they plan on making more, or I think torq motorsport might still sell the extender still.

@@ikiru1969 thanks for the response. They are not making anymore as of now.

you can but its not worth it, you would need to built the motor to support it, it would be cheaper to get a complete used turbo motor, but you will still need to change of other things to make it work, if you can find a rear crashed one to buy then you would have all the parts. I would say sell non turbo and buy a turbo car, or do a motor and trans swap like from a honda or something might even be cheaper. Sorry not the answer you wanted to hear

@@ikiru1969 I appreciate the detailed response!

NP

check for vacuum leaks, also you may be getting a code if you changed your inter cooler or intake. the stock valves see, to fail once they get to hot,

Welcome

have not put it back together yet, I have been working on other projects

@@ikiru1969 pls make vz61,i need more info for tappet plate 🤣

Glad it helped

i can but it will be a while, I am on a 2 month cruise, will be home in November

I use a strap through the pully and tie it off on the axle,

Yes the old ones where broke that is why I was replacing them, the ends where replaced with new ones.

@@ikiru1969 @ikiru1969 were the "barbs" that hold the wires in on the new ones easier to push up without breaking them, like that one broke when you pulled the wire back? I just got 3 connectors from the scrap yard and they all broke instantly when I pushed the release barb up even a little bit to release the wire. I was even able to break the black plastic in the connector with my fingernail, it just falls apart. I have the new part coming soon, so I hope I can release the new wire it comes with without breaking it... I got the yellow part out very easily without breaking.

Yeah the old one you remove from cars will most likely be easy to brake, once the plastic get brittle its almost imposable not to break, I bought a harness from eBay and just used them for replacement's

@@ikiru1969 Very bad design and material quality!.. I'm surprised .. if you look at many other engines, they have bigger, stronger connectors.

Yeah its a cheap car so cheap parts. but it would be easy to upgrade the parts if you can find a plug that works with the coils or upgrade the coils and change to connector also

i might have done it a few times over the years

I guess it depends on where you are, here its a water pump, but its the part that moves coolant through the cooling system of the car

yeah it worked out good, I was just going to use a nut and bolt

I got them from Amazon, I priced around and they where the cheapest i could find,

it is a very neat car, lots of little things to learn, but not hard to work on

Yes, I did figure it out, thanks for letting others know also. I might have forgotten to say something about it

yeah, done with these pumps, ordered a powered one, now just waiting for it to come in

I pull the fuel line above the pump and stick a funnel in the hose and put some gas down it.

you would think

its been a while but I think I said in part 1

Glad it helped

Just about any mob you can sneak up behind and can do this way, there are a lot of tools in the game people miss.

I cleaned it and it was running great then the fuel pump went bad and it has been acting up worse then before, I am ordered a new carb, so I can deal with the old one later, will check the hole and see what it looks like

Check the new one before install can't recall what the hole is called I do know that it can cause a man to have a bad day

just had a MRI I go in tomorrow to see why its not healing

yeah on my list of thing to do

Thanks for the sub!

glad it helped, I am still working on the car just trying to get a few others out of the way