Видео

Im doing this to a v hull aluminum 14 ft smoker craft

Thank you, your video explained it better than the factory video explained it. I got mine done and ready.

How did it turn after use?

You cannot find them now

That's not exactly low water for that stretch but I guess for the jetskis it is. Also it's illegal to run motorized boats past fall city but it looks like a fun run. Would definitely not recommend doing it again, you could get fined and your boat impounded.

Can you give the make and model of the hitch you installed on your 2023 Prius please.

Sweet build man. I’m currently building a rail/ bug with a bus trans and j32 Honda v6. I like how you used your old torsion beam housing integrated into the front end.

I’m building one soon, what speed can you get out of it

Hi, have you used it and did it work? I ask because I want to do the same and need it to hold a backrack and support approx 200lbs. Let me know your experience. Thank you and useful video

Have you used it yet? How did it go? I ask because I want to do the same and not use it to tow but just have a back rack on it and the back rack needs to hold close to 200 lbs. Let me know what you have done with yours. Thank you in advance

By removing the gearbox lid first you risk damaging the output seal, it’s incredibly easy to over compress it. Yiu don’t need to press anything on these units. Welding glove left hand, spin impeller whilst heating.. as soon as it spins freely in the shaft simply lift it off. I can’t believe how bad this information is!!!

You mention you’re installing a rear diffuser? Mind telling me what diffuser you’re installing? I’m looking for a diffuser too

Great video. It looks a lot easier than my 2016 Prius hitch installation, where the entire bumper had to be removed. Plus, that hitch wasn't hidden. I have this type hidden hitch on my Tesla Model S and it's nice that you don't have to deal with clearance issues when you don't have the hitch installed. This will be going on my wife's new Prius.

Do you have a video for the installation of trailer lights wiring? And when you took off the side covers, could you see the reverse bulbs accessible from there?

Thanks for sharing. Do you think that middle plastic cover that you intentionally left out would fit back in with the hitch installed?

Omg thank you so much I can't believed this worked I didn't have electric tape so I used scotch tape. AND IT WORKS very well I rapped it around a small pot perfect size 😅

Can you possibly link what hitch or what brand this is? Thanks

What model of hitch did you buy? Link?

thank you sir

promo sm

Don’t where you filmed this but it reminds me of the Brazos River in Texas.

I build gear boxes and its fascinating to find out this is basically all the same, but I'd be so afraid to take mine apart lol

thats a bad ass ride! I'd love to join but man, can't afford to crack my hull on a rock. sure tempting though.

ABSOLUTELY GENIUS IDEA!!!! THANKYOU!!!

The cone washer on the front of my impeller was lose when I got it back from ati. I’m sure it’s not supposed to be loose but I’ve try to tighten it with no success .

You need to make an update video on this Baja if you still have it it looked great!

Why didn't you show how you pressed the first shaft down, skipped right over that

What size jetski did u put in her

Maybe add layer of duck take in-between lol I was on a cleaning row and now I have to order one

Ohh my goodness! Love it. Love you for sharing this!! Thank you thank you!!

How do you not suck up rocks in the park running that shallow?

I really hope this works. I keep ordering the wrong belt

Спасибо братан, помог

I'm gonna try to fix my broken belt by wrapping electrical tape around the outside of the broken belt so that the tape shouldn't heat up as much.

I'll say this much, taking it apart no big deal. Putting it back together correctly, NOT

If it was this easy, everyone would do it. I promise you all, it's not easy. The tolerances when putting back together, have to be in the thousands. Trust me

Not that easy. The tolerances have to be dead nuts and only procharger knows the specs.

Couldn't really hear anything when engine running. Maybe list some of the parts in the description.

The Sanden 709 can be taken apart and greased in the back then a plug put in which seals the 2 sides so NO oil used or pushed into the air lines. Used on like 97-06 Jeep wranglers. Or you can buy one ready to go from Extreme Outback their Extreme Flow line for around $450

You're the ghetto MacGyver thanks bro it worked like a champ

Nice send!

Yea its A LOT OF WORK and engineering. Great job ..too tough.

Do you know a part number for just the high speed seal? I know the low speed one.

You can also try using a needle and thread to sew together the broken old one. You just need to make sure to use a lot of stitches and then tie it off really well when you're finished. I used it temporarily when i waited for my new one to come in the mail and it worked great, but i don't know how long it would last long term.

5 minutes or five feet. That’s how long it is going to last

The bearing that went bad do you have the part #

Cloth tape for wiring harnesses might hold up better. It won't melt like plastic tape and has more of a grip than smooth plastic.

Thanks brother!

So cool! You gotta post post another when it’s all together or even a update?

So how's it coming? Part 2 yet?