- Видео 25
- Просмотров 71 817
Hot Rod fuel hose
Добавлен 27 дек 2014
Video (1).mov
#hotrodfuelhose #hotrod #lsswap #lsswaptheworld #lsx #lsxcanada #engineporn #anhose #anfittings #performance #chevy #mopar #dodge #ford #chevrolet #gmc #truck #car #ratrod
Просмотров: 98
Видео
hotrodfittings.mp4
Просмотров 1532 года назад
#hotrod #racecars #lsswap #hotrodsandmusclecars #lsswaptheworld #lsxswap
Assemble braided PTFE AN fuel lines by Hot Rod fuel hose
Просмотров 60 тыс.4 года назад
This video shows how to properly install your new AN hose fittings onto your PTFE lined hose from Hot Rod fuel hose. Visit us at www.hotrodfuelhose.com for all of your AN hose needs.
So how do you "clock" a pair of 90 degree fittings on the ends?
This is a acquired skillset . A bit of anti-seize on the threads are a big plus. Going together hard means comes apart hard. Nice stuff.
do u need this? we are seller from China.
Thank you!
How hard should those fittings thread on during the assembly process?
The smaller size (an6) will be tight to get the nut over the nylon braid. As you move up in size it gets easier. If you are finding the nut extremely tough to thread on the fitting you likely have a strand of stainless or nylon that has gone wild and is between the threads. Make sure to trim any frayed out stainless or nylon so it doesn't get stuck in the threads.
Do you assemble these dry and use no oil on the nipple?
We do not use any lube to assemble
Really well done, straight to the point
Awesome video thank you!!👍👍
Thanks for watching!
I didn't have a vise but I do have a 10 ton press for making hash rosin with. Easy to follow instructions. and a great kit so far. Feel like if I get a leak, it's probably cause I screwed something up lol.
I can't cut the nylon off for the life of me. It's like it's glued to the steel braid. Already messed up a fitting ugh.
It would be good if you included video of the tightening process so we could get an idea of how hard it should be to get down to the 1mm gap. I hope I did it right!
Noticed you say leave a 1mm gap - what is the purpose of this and is it applicable to other brands? What if I do not leave the 1mm gap?? Happy with my stuff I got from you btw :)
Some brands recommend it some don't and many don't give any instructions at all. At 1mm the ferrule is typically full seated and going any further just puts a risk of rounding out the nut due to the force needed to "keep going"
@@justingorzitza3390 Ha I agree with you on that and it make sense why some of my nuts look a little scuffed ☹ I will do this in future. Thanks.
Your nuts are scuffed because you're not using an aluminum AN wrench You don't want your wrench to be harder than the material you are using it on
Ordered my kit today for my 300zx project. I don't have a vise or heavy duty cutter but I'll figure it out or find someone who can help!
Thank you sir we appreciate it!
@@oneguygarageparts ,. Fi u hu yyytgff to l HD
Can you guys get a better red anodized.. the current red is too pinkish
possible to install without a vice? Love your products btw!
The vice makes it WAY easier but guys have completed the install without.
Thanks for the tips. we just ordered an efi kit from you guys
We appreciate the support
That’s great info. What if the hose is already in the car? Possible to do?
It's not ideal but guys have made it happen before
Please show how you got the nut on the hose, this seems to be the most difficult part.
We are in the process of creating a professional video that will show this but it will be a bit. The key is to use only a single wrap of tape, round out the liner, and finally treat the nut as though it threads onto the hose. Place the nut into the vice and twist as you apply pressure to push the nut on