great and all but can someone tell me what those are called?( the black hooks that hold the line in place that they hooked onto the bracket 2:36 ) even post an amazon link please. i can't find them for the life of me!(nvm found it after few hours at least as close as possible: Nite Ize CamJam XT Aluminum Rope Tightener )
This is a poor video. It doesn’t explain why you have to do particular steps for example which means things can go wrong because you dont know what your are looking to avoid. The jims roller door video is much better at explaining what and how to install a door. Regret going with this company.
Mrs Richards: "I paid for a room with a view !" Basil: (pointing to the lovely view) "That is Torquay, Madam ." Mrs Richards: "It's not good enough!" Basil: "May I ask what you were expecting to see out of a Torquay hotel bedroom window ? Sydney Opera House, perhaps? the Hanging Gardens of Babylon? Herds of wildebeest sweeping majestically past?..." Mrs Richards: "Don't be silly! I expect to be able to see the sea!" Basil: "You can see the sea, it's over there between the land and the sky." Mrs Richards: "I'm not satisfied. But I shall stay. But I expect a reduction." Basil: "Why?! Because Krakatoa's not erupting at the moment ?"
yeah they all do it, don't seem to take any notice of their viewers though, it continues. Watch some welding company videos and they all use rock music, does nothing for their presentations.
Thanks a lot for this video. I managed to lower my manual roller door and fit a motor to make it electric. All following your technique using the rope at either side. Worked a treat. Took 3 people to do it.
Hey shit for brains look at the brackets that is holding up the rollaway door it’s blowing out that means. The door is too heavy for the cheap ass brackets
tek screw on the sheeting looks so tight that it dents the sheet lol
great and all but can someone tell me what those are called?( the black hooks that hold the line in place that they hooked onto the bracket 2:36 ) even post an amazon link please. i can't find them for the life of me!(nvm found it after few hours at least as close as possible: Nite Ize CamJam XT Aluminum Rope Tightener )
🎉🎉🎉
what is the size of the Bolt you used in fixing the support to the steel column?
10-16x16 hex
This is a poor video. It doesn’t explain why you have to do particular steps for example which means things can go wrong because you dont know what your are looking to avoid. The jims roller door video is much better at explaining what and how to install a door. Regret going with this company.
did you get the stateg specific installation manual from centurion website
Mrs Richards: "I paid for a room with a view !" Basil: (pointing to the lovely view) "That is Torquay, Madam ." Mrs Richards: "It's not good enough!" Basil: "May I ask what you were expecting to see out of a Torquay hotel bedroom window ? Sydney Opera House, perhaps? the Hanging Gardens of Babylon? Herds of wildebeest sweeping majestically past?..." Mrs Richards: "Don't be silly! I expect to be able to see the sea!" Basil: "You can see the sea, it's over there between the land and the sky." Mrs Richards: "I'm not satisfied. But I shall stay. But I expect a reduction." Basil: "Why?! Because Krakatoa's not erupting at the moment ?"
👏👏👏👏
great vid would be awsome to be able to heare whater your saying over the muzak.
Those brackets looks like trash
Turn off the music please
thanks
Laughs in Lawrence roll up doors
Music is so loud , you cant hear person giving instructions. Waste of time trying to listen. Sorry but annoying.
the way the roller is mounted is very dangerous workers must use a safer lifting method . forklift material lift
I was struggling to hear him over the music
How far from the wall
Very good
Please remove the annoying music when you make these video’s
ترجمة بالعربية
anyone else notice when he was drilling the first bracket hole, he was going in reverse? lol
I think that is the camera. like sometimes car wheels appear to go backwards?
@@themeanaverage.1692 i was joking; i think you're right.
I was just about to post this, lol!
It still upsets me that the bit slipped on the second hole and he let it sink through out of alignment. Poo
The one job I just don’t do. This isn’t a DIY job. I’ve seen some terrible stuff on the internet.
Coward
Can you cut the size of the door
This would’ve been a great video without the music.
yeah they all do it, don't seem to take any notice of their viewers though, it continues. Watch some welding company videos and they all use rock music, does nothing for their presentations.
Great video guys, what was the dimensions of those doors?
Thanks a lot for this video. I managed to lower my manual roller door and fit a motor to make it electric. All following your technique using the rope at either side. Worked a treat. Took 3 people to do it.
I lifted and fitted a 2.8m x 2.8m door using 3 tie down straps on my own. You just need to take it slow.
LoL my shed supplier sent me 'A' series brackets with roller doors 2.8m x 3.5m ........when hoisting the door the brackets simply bent.
Hoisting like this doubles the weight acting on the bracket.
Hey shit for brains look at the brackets that is holding up the rollaway door it’s blowing out that means. The door is too heavy for the cheap ass brackets
I know this work bicouse my work Shop in india
Bicouse my work Shop in india
your point being?
@@oo0Spyder0oo hi
I know this work
Nice one
Great sharing💙
Where can you buy those pulleys with clips to pull up the doors? Anyone?
I need these as well. Did you find them?
@@gsxr600rafii nah mate
@@joshchanny Think they are 'Eye Sling Hooks' or 'Snap hooks with eyelets'.
ruclips.net/video/nxAkXtAz4iU/видео.html
Depends where you’re from
Roller door not raning motor
Why the front panels on your shed shows dents around the screws?
@Jesus Lewis yup, been watching on Flixzone} for since december myself :D
@Jesus Lewis yup, have been using Flixzone} for since december myself =)