Видео

Thank you I understand now

Sir for a two way speaker having max power of 500 watts What is the amplifier wattage I will used? Thank you.

wattage?

Nice one engineer

The pfl when setting the gain knop, should it be press down or up?

Thanks for sharing

Nice tutorial learnt a lot from that

Was a good lesson

Hi,can i wire 1,2 ohm speaker and 3, 4 ohm speakers to result around 6/8 ohms,my result îs 13.6😅.

Watching sir thank you for sharing

Watching here very informative vedio thank you for sharing 7:16

3:21 Interesting ... Learning here ... So, what if the amplifier is matched exactly to the speaker power? what would happen in such a case?

Your maths is very questionable My friend .Do you not understand percentages ?

You really need to go back to math class 50% plus 400 is going to be 600, 50% plus 600 is going to be 900 you think you know what you’re doing now you’re telling people to get amp that are gonna be way too big for their speakers

Awesome job. So simple to understand and straightforward

Years ago loudspeakers were tested with continuous power. The winner was the AR- LST at 12 wares continuous. Any more and your voicecoil lights up like a light bulb filament.

I have mono amp, 8Ω=4.5W/4Ω=9w/2Ω=18w/1Ω=36w/0.5Ω/72w My speakers are Proson Event 10 pro wired parallel with load for amp is 2Ω nominal, and because my amp is capable provide power for very low resistance sound volume for listening level is good and plus some more if needed. So with all that i want to tell you that it is not always needed big wattages. My advice for everyone is that chose amplifier where is youre speakers nominal impedance supported half wit it and nominal rms wattage double

Thank you ❤ keep teaching us

Sir let's say am using 6 single line arays each having 8ohms and 400w What should be the amplifier

which one better a single 18"500w speaker or multiple smalest speakers in the same power rating 500w?

Name of That 🎤 mic Plzzzzz

Peak N RMS are the same, peak power is short period of program power to the speaker Continues or program power is the continuous power delivered to the speaker. You didn't mention spl?

Now i know, i have been looking for a video that educates about feedback. Can you do a video doing it practically ?

Can you make a video of sending matrix to mixes

A bit of mix up with your “50% above” rule for amplifier to speaker wattage. 50% above 400W is 600W and not 800W.

Very nice

The important rating for an amplifier is RMS power. RMS tells you the sustainable power. The important rating for a speaker is Maximum power. The maximum power tells you the power level above which the speaker will be damaged.

Um... if you have a 400w speaker, an additional 50% power would be 600w, not 800w. 800w would be an additional 100% power.

Powerful

Sawa kabisa

Not a word about speaker sensitivity in db

Am a bit confused, is the manual on the right on the board for speakers or manual, because the whole time you are working on the speaker drivers and on the manual it should be the specs of different amps?

I will wait on God

Thanks for the excellent video! I’ve been reading up for about a week, and this is the clearest explanation. How does one know how many speakers one can connect to a power amplifier?

Thank you sir🙏

Great, short and sweet. I've been trying to find out the exact information, but had no luck until now. Thank you and wish you the best!!

50% more than 400w is 600w, not 800w

Great work here. I love the consistency.

Good content Sir👏

Good nuggets business coach. Love it.

Very very important

I hate to be negative to anyone trying to teach people, but this class jumps all over the place. There is no rhyme or reason why topics are in the order that they are. I mean the first thing the instructor talks about are amplifiers! Why amplifiers? It's not the first part of a signal chain, nor the last part. Then auxiliary outputs? The instructor hasn't talked about inputs or signal flow at this point, yet wants to talk about aux outputs! I would expect a introductory class to start with the basics and then logically build from one topic to another. I mean the instructor talks about compression and EQ (which are more complex concepts) before he even talks about gain and gain structure (which is the most basic building block of sound reinforcement). I expect that any real beginners to audio engineering are going to have a really hard time comprehending all this information because of the way it is presented.

❤❤❤❤

❤❤❤❤

Thank you very much sir, I've learned a lot

❤❤❤❤

thanks so much 👋👋👋

Very good informative video on effects. Thank you

Thank you this is amazing..I just started with Loud sound.

Great