Видео

Erm my lil switch isn't an on and off switch it's a retractable one.. Soo do I hold mine down

Abs or Traction Control need to be off ?

Рекомендую просто высверлить заклепки и снять карбоновый наконечник. Потом выкрутить болт , снять флейту и заклепать обратно карбон. Выйдет гораздо окуратнее.😊

А у меня боль не выкрутился и слизало грани ,пришлось сверлить болт два часа😢 . Интересно,почему нельзя с завода делать так , чтобы заглушка снималась легко😅

Tank ped link plase?

We need more information about this motorcycle.

Do you just let the clutch go? Or do you slowly do it like when you take off ive been trying to do a burn out but i don't wanna mess up my clutch so i havent tried that many times do i let the clutch go completely or slowly do it? I know he explained good in the video but i just wanna confirm this

Bro just saved me

make sure tire pressure is high, hold it at high rpm, make sure brakes are good and hold it very tight for your first attempt, remember brake is the most important thing here to avoid accidents, dump the clutch a little and pull it back to get a feel and if you can have somebody confirm that the wheel did spin, do it a more this time and keep building your confidence till you reach a level that you barely touch the brakes and are able to play with the throttle

Chomp chomp chomp

在我看来 CB1300比那些哈雷强很多！方方面面都是！老美还需跟日本合作。不要徘徊在当初了。这样及其矛盾！及其装逼！承认了吧。

The engine is on fire

I drilled a 13mm hole to expose the bolt after using a thin piece of card slid between the can and pipe to line up the bolt easy 😊

you guys think that this will also work with the akrapovic S-Y7R11-HAPT ?

U did this and my front tire just slipped and I fall

0:16 the driller made dodge hellcat noises💀

What sc model is the exhaust ?

Fällt ja gar nicht auf 🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️

People are saying they dumped the clutch and stalked. Other people are saying to slowly release it keep it at the Friction point and slowly release but that will burn the clutch. Other people are saying to dump the clutch but Rev the rps very high. I think if Jesus christ was learning this move for the first time on a motorcycle he would just say fuck it cause you can't get the truth out of anybody.

このバイク、Y2Kじゃなくて420RR だと思います。

Nice edit ZX10R ka sound laga dia 😂🤣

2km/liter is quite cleaver considering it using turbine engine, most 1000cc consume 5-7km/L

Yahşi

Tüv sagt nein

ใส่แบบนี้อัตราการเร่งรอบต้นปลายหายมั้ยคับ

Instructions unclear, just sent my bike through neighbor's living room window

What happened if you do this everytime you start the bike? Will it ruined the engine?

Don’t dump the clutch keep it at the friction zone and then you’ll start to burnout because if you dump it too fast you’ll stall your bike then you’ll look stupid

Not working for the 24 model! They welded the bolt to the inner pipe, you can remove the whole back tip by drilling al the rivets in the back and then you can reach the bolt

Did exactly this, wheelied, when the front tire came down I stopped and got launched off. Tire somehow kept its traction

Zx 10r sound 😅

7100oil???

sound coldstar zx10r 2018😂

If you are think that being when can if do that of is where wasn't can be without it. Do when bring is of it can you up is of there? Or can bring when be of that is? When they are there is the in of doing with them they are that ones. So if are they that one is you and without then? When do so can if it was there when it will didn't can then how does it went to that before there is on timing inside without them?

Lol I left light on, on my Bike. Voltage was low and I didn't know how to start it. I tried this but had it on neutral and kept starting and failing as it rolled down hill. It would seem I didn't dump the clutch which was the problem. I eventually called AA and the guy was soo friendly, he jumped on my bike and bump started it within seconds, I was soo embarrassed. I asked him to show me how it's done and he did. I'm a new rider, only been riding again for a week now.

That's not the correct way to do it ... best way is to drill out the rivets and pulling the exhaust appart

i thought ducati’s were dry clutch,

My brain: vududududuudududududuud

Fuqers they try they best that you dont remove it … why ?

How do you know were to drill the hole

Some of them you to drill out the pop rivets remove end part of the carbon fibre because the bolt is welded to the exhaust

Kw ps?

C est exactement ce que j ai fait sur ma z1000r de 2018... l embêtant s est toujours de bien récupérer la visse...😂

Don't dump the clutch, your bike will stall

Is it the same way on xadv 750 2023? Akrapovic

2km/l ☠️

idiot of year award

What is the link to this

Better than z900😊

what cause the inline 4 flatplane sounds like rotary engine when idle? the brap brap sounds very nice.