Видео

2 joints

why my honda 2018 (led headlight- left side)only fron turn signal (left side) does not work? Also, same fron left headlight (LED) when switch FOB key off front right headlighs flash but not left. Can you help if this is light bulb or rely? Please share experience. Thanks

I am trying to add led puddle lights that turn on when the car door opens. When I splice into the black and green wire in your diagram, the led light turn on when the dome light is off and they are off when the dome light is on. I put the positive wire from the led to the green wire (in diagram) and the ground wire from led to the black wire (in diagram). How do i get the lights to tilurn off and on simultaneously? Thanks so much for your help.

Instead of having music tell us how it works. Note that each pin is numbered. 85 and 86 are the coil pins while 30, 87, and 87a are the switch pins. 87 and 87a are the two contacts to which 30 will connect. If the coil is not activated, 30 will always be connected to 87a. Think of this as the relay in the Normally Closed (OFF) position. 85 goes to the power window swtich which connects to ground. When 85 on the left relay is connected to ground 87 connects to 30 placing positive down the blue wire to the motor. The right relay is at rest so 87a is connected to 30 causing negative (ground) down the purple wire to the motor. When 85 on the right relay is connected to ground 87 connects to 30 placing positive down the purple wire to the motor. The left relay is at rest so 87a is connected to 30 causing negative (ground) down the blue wire to the motor.

Thank you. It is a very helpful short to the point video. Very informative. Could you perhaps help by making a video of how to connect an old alternator to an external 6pin voltage regulator- please? Colors are BLACK, YELLOW, RED, BLUE, WHITE AND GREEN coming from the REGULATOR.

I TRIED. DOESN'T WORK. SHORT CIRCUIT.

Where its the temprature switch in this system and the presure sensor for the gas.

Every time I do it the relay become the source of using power. Since the relays in the middle

🎉🎉🎉🎉 Greatest animation Thanks million ❤❤

I want to add two fans and I want them to work with engine cooling temperature or to work with the A/C compressor clutch. Can you explain to me the method?

you can also swap the negative and use the positive towards the switch also right?

What if there is no indicator light? I just sent the alternator for repair

Thanks!

Can i tap 86 to original radiator fan motor positive line? It also has 12v positive

Thank you!

Thanks❤

you shorted the terminal 87positive and 87a negative this is wrong diagram

I like this diagram. helps a lot. thanks

God bless you too🎉❤

It was easy if you just wire the cables by hand to see it.

Out of no where my light switch doesn't turn on or the fog lights now.

Bro this is the most simple diagram ever THANKS 😂😂😂😂

How about alternator running 2 wire? Although the pin in the alternator has 3pins

I’d like to swap my mechanical fan to a electric fan, this could be turn on by the cooling temp sensor and the a/c compresor. What could be diagram for this???…

Ac will cut off through the thermostat, but old cars dont have thermostat how did they cut off? Through the high pressure solenoid?

Good job very helpful video.

What in the phuck is this? And what kind of drugs have you used

Good working bro 💯

Wala Kang kwinta

I didn't get this at all. All I know is that I get no juice on the switch till I turn on my headlights, then my fog lights still don't come on. I tried using the OEM defrost switch but it lights up while I have my finger on it but shuts off immediately when released and in either position I still get no fog lights. Any ideas? Thanks for any help.

The last remaining pin on the alternator should be connected directly on the battery, not on any positive cable.

Bakit pinalitan sir? Anu problema?

Where do 85 (switch)goes to positive or negative

4pin?

J'ai trop aimé cette cheman

thanks a lot...very simple and easy to understand diagram..now i can custom my own dome light with my own style...no need to buy already made by factory

Well done posting

❤❤

I have one interesting problem ...one of my foglight is working while the other one is not working...now here is the interesting part == the one not working when tested using multimeter generates 2.4 volt before it is even switch on while the other good one no voltage before it is switched on..... What could be the likely problem in this case?

What if the battery light is still on and the alternator is charging well?? The battery is good as well, the light just won’t turn off💔

I like it 😂

Think you very much Brother 👍👍👍👏👏👏

So the two 85 goes to switch like ground ?

Which wires connect to the switch??

Easy to comprehend, it's straight to the point, very helpful and educative.

One of the worst videos I have seen. You are covering the pin ID, music is way too loud, and worst thing, you got distracting junk flying in the backgound.

How to add an after market for a floor mat lamp, do i need to ground to 4 doors each or just bypass any circut of any door

'PromoSM' 🙄

Hey what guage is these fog light wiring Harness

Where the lo/high pressure switch