Видео

I seen another video with a simple water bottle hole in the top to find intake leaks it will bubble by the leak saves cans of throttle cleaner lol

Was a late night video now that’s a mechanic 👍🏽👍🏽

Like show

Thanks for the illustration... You made it easy. Yes I think I'll need a helper as well when reinstalling.

My peacock's on LOCK! haha... excellent video man, I appreciate the attention to detail!

Is this the same for a 2001 E2 54.2 L

Thanks bro life saver

hey bro can you tell where I get the book do you have on the video? Thanks , also nice video i waiting for the gasket to start my job

I have the exact same engine and truck man come fix my truck mann im in south texas

are the blend door the same for passenger and driver. all the ones i keep finding say "Main"

What is the book you are using I would like to get one

Helpful video. The coolant drain valve is a petcock not a peacock 🦚

The lower portion of the upper intake HAS 8 isolator bolts, not 7. They've also been revised to green rubber instead of black. Cheers

Were do u buy the book?

Mejo you used the wrong gaskets, they make some that are aluminum with the rubber orings, instead of the junky plastic ones.

That's a iac valve not a EGR valve on top of throttle body.

Nice Video! Just completed the job. went through a whole pack of bushings and had to go get more dropped 4 broke a tab of 4 as I pressed them in. Dealer gets 6 hrs for this nightmare job. OK here the secret. dont be afraid to pull the fuel rail on left side, I tried for couple hrs, many bushings. Just jiggle it and lift it up. I only removed last one and held rail up with a zip tie. Now you can use your left hand. Im right handed but couldnt turn the bushing as I tried to get it in. Using left hand on left buttterfly valve gently push in bushing stoping before it goes in all the way. Look with light and mirror to make sure you see all tab ends in the square hole. Pushing it in with out checking for all 4 tabs is how I broke 3 bushings. think I could do it again with 2 bushings and 1 hour start to finish. DIFFICULTY....1-10, 8.7

Recueda que tienes que evitar hacer el trabajo de nuevo si dejas caer algun opjeto dentro del intake debites ser mas precavido

Will a blowed plastic intake cause you to get water in on the pistons

Where in Texas are yall?

I have a 98 ford e250 with that same engine been there done that

Good afternoon my friend, can you please tell me the numbers of gaskets (spare parts) for repairing intake manifold leaks??

The cold ac inside my 300c aren’t working. It only blows heat for both vents 🤦🏾‍♂️what could be the issue ?

Amigo sabes donde esta el knock sensor en estas camionetas 4.2 según yo iba debajo del Intake Manifold pero no lo miro en tu video..

Hey man I’m having some issues with my 300, do you have instagram or anything that I can message you off of?

where do you get a maintenance manual like that?

Ok. I thought I must've nodded off somewhere, but from some comments, I didn't... I'm one of those people who not only need to be Told every step on how to do something, I really must SEE every step on how to do something. And generally more than once :D But I suppose these 3 vids will help those who already have a working knowledge... As for me, I got just enough information to decide that I may not want to try this myself. :)

Thankz Greetings from Mexico.

😍

Increíble 😮

I really found this helpful ❤

It's easier to remove those bushings if you take the whole intake off.

Donde puedo conseguir el manual que se be enel video

So what were you experiencing that made change the runner control in the first place? I have a lean code I've been chasing since march and more recently, a runner stuck open code. Truck is smooth, but at time it misfires, so I'm getting ready to do this, gaskets, and injectors all in one go.

How do u not have more subscribers bro... best diy video ive seen yet. Especially on this exact subject.. noone else shows everything and tells you everything... OR THE FACT that if your just doing the upper intake spacer whatever it its that u dont even have to drain the coolant... everyone says drain it and disconnect hoses..

Bro what happens if you start without taking out spark plugs?

I been sealing with mine for 1 whole months 2 gaskets now and still leaking testung with smoke machine pain in the ass tbh. It keeps leaking in the back midle side I put silicon on bottom and top fot the second ine and still no good -_-

What was the problem? I have cylinder 2 misfire. Im trying to see what you did to fix the issue.

Can you dou in Spanish 😅😅

Oh man💥 you're amazing' - a real glutton for punishment ain't cha 🛠

Hey, you skipped a whole lot on how to take the upper intake manifold off that’s the only reason I’m here…..js

Fix Or Repair Daily, I'm saving for a tundra!

Legit.

Good video but its not the head gasket its just called the lower intake manifold gasket

I just watched your video replacing the lower intake gasket and i was literally thinking how those fuel injectors look kind of dirty. I'm in the process of replacing my intake gasket as well, i removed the lower intake in august but I've been procrastinating since then. I suggest that you clean all the injectors, maybe they're clogged, and while you're at it replace the o-rings. I cleaned mine and you can see the difference. i think that all the PO17X codes are too much air/vacuum leak because it calls for both banks, as for the P0303 faulty/clogged injector or loose connector, P0401 i think you did good unclogging the ports. This is just my personal opinion as a DIY.

Do you have apart number for the plastic retainers for the control rods?

I just did this to mine two nights ago bro.

The bolts are not 14mm lol but okay

can you do an update video with this setup, like a soundcheck and what not?

I literally cant find my passenger blend door actuator