Видео

Just curious why you think this is better than a mid mount mower?

Beautiful, Great Job I just bought an LX2620 like yours. It will be delivered first of next week. Please list what coating products you used so I can make mine look that good. Is it Ceramic? New to me, Thanks

We can all see the love that went into this. Very nice job and you enjoy the Z06!

is the module a different one or was it rebuilt. I heard something about programming the module after replacing. I’m planning on getting a module replacement from another car. Do you have to program it?

I tried your fix without success. I went to the local Authorized Honda Power Equipment service center and was told it was most likely fuel tank debris had fouled the carburetor. Thank you for the video.

Nice Rig I love my Finish Mower as well it cuts better than my zero Turn 👍

hello, i can get one gx120 for 150 euros, good deal ?

This is a far too frequently occuring problem with hondas. ABS module failures. It really should be a recall. Now 2024, and the honda dealership cost is up to $2,000+ to replace the entire module not just the broken computer. They will not replace just the computer. There is an online service you can ship your computer to that will refurbish it for $200-250. If you don't mind cracking open a glued/sonic welded plastic case and doing so solder work yourself, you can possibly do the repair for less than $100. Typical problem is the shotty wires they used to connect the harness co nector pins to the circuit board. I cut mine open with a dremel and found 4 wires that were completely disconnected. I removed all of the original wires and doldered in thicker copper wires for every pin. Glued the cover back on and sealed with heat resistant tape. Plugged it in and it work just fine. All the panel lights wwnt away. Had to get a friend who has a $4,000 scanner to clear the abs/vsa codes.

What a jewel of a Tiger...ceramic expertly applied turned it into an unbelievable beutiful. Nice work.

Nice rig! The cut looks pretty good too! I would recommend removing the front loader when mowing. Much less chance hitting something and less weight on the front axle while doing maneuvering. 👍

very nice , my 170 needs that so when would you like to start?

Nice! I’ve got a bx and I’m debating skipping the b01 and just getting an LX20

Did the tires affect your MPG? How are they holding up now?

Lmao😂

Are you planning to mow with it, or just for show?

2024 $3000. HUGE BRAKE SAFETY ISSUE DUE TO FAULTY INTERNAL WIRING DESIGN OF ABS MODULE. FUCK HONDA. FUCK JB.

sounds like everyone wants a recall or some sort of compensation.. i need to see action not just words lets get this thing moving #recallthesecars

That sound people get from the Solas Amita 3 aluminum prop is not harmful. It’s called prop singing……The manufacturer can eliminate it by beveling the trailing edge of the blades but they probably won’t because it means paying for tooling again. Must have been a rookie engineer.

Bacano.

Factory 11 pitch prop? I've got a 14' Meyers jon and I just ordered a df25a, I bought 3 different props to see which works best for me

It’s been 2 years since your review on your tires , I have a 13 tundra with 180K I’m needing tires how are your tires holding up ?

I wouldn't drive it. I'd just sit in the garage and look at it.

Paint on John Deere is super thin be careful

Same thing happened to my 2006 Honda Pilot. I replaced a wire harness to the passenger side front wheel bearing. Part was about $20. That was 3 years ago and the lights have been off ever since then.

what did you use for polishing and finishing? I just bought an X540 used and I want to super detail it as soon as it get delivered. Looks fantastic!!!!!!!

Easy to move with those wheels and its built like a brick shit house . Well done guy

Beautiful machine!

PERFECTION! Looks amazing!

Any update on your review of this tire? I'm about 6 months from needing a new set on my 21 F150

Wow thats pretty powerful water pump.. the wb20xt version is not available in our area. Instead they have the WL20XH version, powered by gp160 engine. By the way what is the difference between the WB and WL version?

Dial gages can be all over the place for gap

Awesome Job congrats

love them decals on the motor...where did you acquire them?

What is the oil capacity of that gx25 engine?

Thanks for the video. Just ordered one, should be here Monday. If it runs rough, the plug gap is the first thing I'll check. How has it worked for you after 3 years? Any issues? Thanks again.

Wow nice mini pump, what is the ideal pipe size for that pump, im just using it just to transfer water. About 50 to 60 meters in distance ( no elevation).

Does fit in any atv?

Soooo satisfying 😊

I had a honda before for 12 years, no problems. Now I have a generac 3200 inverter generator, Perfect.

I bought one overcharged very easily, change for another one, same. Garbage.

Thankyou Thankyou Thankyou !! One year on from you fantastic video you would have thought Yamaha would have fixed this issue but no joy I purchased a brand new generator yesterday 29/2/24 and it had the same issue. With your help it is now running fine cheers from Australia 🇦🇺

what a blessing to what that experience! gift!

It should have been a Honda recall. Very common, they go all the time. BS !

Looking at new tires for my 2015 Silverado 1500 Z71. So tired of KO2’s. They are rough, noisy, and hard to keep balanced. I do more hwy than off road these days but I do pull a bay boat quite a bit. I went to look at the AT2’s today and saw the XT’s. The store mgr says they are a great tire. That they are quiet and smooth. I feel like they are between a moderate and aggressive all terrain. They look great on the Tundra.

Brazil loves Makita, congratulations on the video, success

Where the headlight would be will blast air into your face like you dont have a windshield

I put them on my 2018 Silverado Great in baby powder snow

thanks very good info. well done

It's well known that this kite has a tendency to dive. Do you reckon that the tail reduces the chance of it diving? Though I did see a partial dive at one point in the video.

I love isla mujeres