Видео

Thanks for sharing! One question. The presented job was in half hour or one hour and half? Thanks

Hello there. One question. I ve got a laothie ti30. If i make a solar setup can i change when the escooter is on drive or i must switch off and wait without driving?

TP5100: 9V to 22V input, 41V output, 1.5A, 60W, 92% efficiency (lithium battery compatible)so just solar panel and tp5100.The step-up module will limit the output current to 1.5A, which is a common feature in many DC-DC converters, including step-up modules. This means that even if the solar panel can produce more current, the step-up module will regulate the output current to 1.5A, which is the maximum current and within the 1.7A max for lithium on the chargers This current limiting feature helps protect: 1. The lithium battery from overcharging 2. The step-up module itself from overheating or damage due to excessive current 3. The scooter's electrical system from excessive current draw By limiting the current to 1.5A, the step-up module ensures a safe and stable charging process for your lithium battery-powered scooter. Keep in mind that if the solar panel's output current is less than 1.5A, the step-up module will output the available current, but it will not exceed the 1.5A limit.

this should be mandated is all cities around the world

I'm looking to buy some electric trimmer. Are you satisfied with this one?

Dupa ce am vazut prezentarea ta am luat si eu una. Nu tocmai multumit. Este relativ grea si prost balansata iar cu acumulatoare de 4ah cu fir eu nu am reusit sa tai continuu mai mult de 10 minute. Capul de taiere(cu filet normal spre dreapta, deci nu usor de inlocuit) cu care vine in pachet are un singur fir nu doua, si este foarte slab - se rupe tot timpul. Cand bateriile sunt la 30% motorul nu mai are putere, se ineaca in iarba de doua degete. Aparatoarea este o gluma proasta(vad ca tu o folosesti fara), este prea mare in dreapta si sta in calea lamei, rotatia lamei fiind inversa motocoaselor pe benzina. Manerul cu coarne nu poate fi strans bine, iar hamul este imposibil de reglat ca sa iti vina cum trebuie. Mai pe romaneste un dezastru de motocoasa, cu baterie.

so dangerous when used without protective shield on blades

I doubt it is half as slower as 36v version because you can cut 2x30mins with it instead of 30mins 36v. The 18v vesion has 7500rpms and 36v has only 6300rpms. So my math doesn't add up with it. 1 battery version is lighter. I know because I have 18v chainsaw and it is slow but also very light to use.

I use it for one year and it is good enough for small areas, up to 300 square meters.

You still ought to wear ear protection

thanks for sharing, cool video! :D

Какой вес косы в полной оснастке

So does it cut through heavy, dense brambles?

Hey dear I am facing power dropping issue in series connection. I have connected 340watt and 380watt solar panels in series to epever 40A mppt controller with 12v battery. It show power of one panel when I disconnect solar connector and reconnect, the mppt show both Panels. It’s hard to do this every morning. It was fine in winter but now summer starting and facing this issue. Using both panels form 2 months. after wire disconnect and reconnect the voltage jump from 33-36 to 75v. If something wrong with one solar panel then it should not work after replugging mc4 or solar wire in the mppt after that It work whole day but same issue next morning Both panels volts amps are little different. Tesla 34.51v maxpower 33.18v. Tesla amps 11.01amps maxpower 10.29amps.

The other solution is a simple MPPT boost controller. Then you won’t need anything else.

Nice video. It would be easier to compare HR if both were on the same graph.

Go get a mt50

Mt50

Nice work!

Great video answered a lot of my questions thank you

If you remow the protection film from the display, it will be easier to read.

I've got Agillo 36/255 with two batteries by 4Ah and it's good.

Ești mulțumit de ea

Yesterday I could borrow an MT50 from someone and found out that one of my two mppt is not read by the MT50. I could access one mppt and program it in user setting, but the other one doesn't communicate with the module as so I can not read/write from the MT50 to/from the mppt. :-( Is there a way to reset this mppt TracerAN to reboot ?

Does it have a cooling fan ? Does it get hot ? Other fanless MPPTs can get almost hot to the touch if you are close to their peak power.

7:10 👌

Dude if you place the unit then you can see display with no problem

Una gran idea... panel solar para cargar batería grande con inversor para cargar las baterías einhell. Superlike que te dejo

Ești român?

Ee

Good Woork 🍻

Hola cuanto dura la batería de 4 Ah gracias.

Es de uso doméstico

Hola que tal es el uso?

Or make a video where you make youre file , Please ,thanks.

Hello where you made youre file for scooter ? Can you send me screenshot of parameters that you change ?

nice work !

great job, how many hours do you need for a full charge ? is there a difference from normal ac socket charging ?

Xiaomi M365 🙂

can I lock the scooter and turn it off? and then turn on and unlock???

Great comparison...The one in eco mode (means with restricted max watt) and custom in drive mode

Как делать на русский язык

How much is your weight man

My mi pro 2 does not taking uphill when iam driving it 😓 very bad i think

Eco thats shit😂

do you damage the battery, motor with hacked software? do you still have this scooter? how much range on standard vs hacked?

veey helpful. thank you :)

Nice video, thanks. I brought a Mi Pro 2 this week and experienced that the factory setting is really not enough to drive uphill. What I don't see why Xiaomi states that the scooter should be fine until 20% slope. Clearly not true.

Buy a car and no hill can stop you 😁

Hi, you watch Ben Fox's e scooter vids? Anyway good luck showing more Mi e scooter stuff. Been a M365 and now a M365 Pro user since 2018 hehe!