Видео

@yungsmile7546 really.. I got con by the white and white..lol

Hibernation? They don't hibernate. During the winter months, they don't create new queens. Only in the late springs and summer months is when they produce drone bees to mate with the virgin queens. If they lose a queen during winter months, that hive is doom. During winter months, nursing bees will continue caring for the new eggs, which will turn into bees. The life cycle of winter bees' lives is a lot longer than before, born at other times.

@feliciaaclark I think it's 20 or 25gal craftsman air compressor. Yes, that's a Hitachi frame nailer.

@rickjudgejr1435 thoroughly rinse away the bleach. Maybe soak in a tub of water after rinse to remove as much bleach residual as possible. They are resilient. Sometimes, the frame has mold. They would clean it up. Always clean all the clean as much as possible because in the end you might be consuming the honey.

Tire was in good shape besides the holes. I got 5k miles out of it after the repair.

@pakkelly it's all about making it difficult, so they make money off you on services and maintenance.

@bigfootswatching9986 why? You did the same dumb mistake as me? Lol

@bigfootswatching9986 your car is still burning oil. That's why your exhaust fume is stinky. The only way to solve this, is to replace all the piston rings and thoroughly clean off all the burnt oil on piston groves. Clean the oil lube ports on the pistons as well. Prolong drive would damage your catalytic converter.

@@tonedubb4325 Yes...i believe what you stated has ruined the Catalytic converter already!! Any other ways around it??? I also replaced the timing chain tensioner as well....no more oil leaks ..... not sure if it still burns oil like b4 since I recently just did the valve cover as well!

@@tonedubb4325 I was thinking of just selling it after I replaced what I just done to it..... Super nice ride and good strong running engine still just wanna still sell it since it get's so much looks/complients and it's just my weekend car anyhow.

@bigfootswatching9986 did you replace the intake and exhaust valve gaskets? They will get brittle and leak. Your major leak is from pistons due to the ceased rings. Only way is to remove, clean, and install new rings.

@@somaxusa hmmm. I'll give it va try next time. Either way, it's pretty easy.

@@tonedubb4325 Agreed! It is just much easier and doesn't require any extra tools. Similar concept when you change belts on the car, you have a lot more room in the engine bay sliding the belt over top pulley as the last step while bringing the tensioner in with a longer wrench for leveraging.

@Neverforget1967 yeah.. I got sidetracked. Still not done. I think I might start this year. I hate to keep changing the water.

@joseg3003 didn't know there is such as tire insurance.

@@tonedubb4325 its called road hazard

It's possible. Just require more work. The main concern is to have a good sea on the lid to prevent water from going in and stink gas from escaping.

@Shellie-bf3wx ok.. but all the aphids are under the leaves. Water only hitting the top of each leaves. I need to spray under each leaf? So much work. Aphids are all over the flowers, too. How should I go about getting rid of them on the flowers. How did they spread so quickly? I checked a after few days ago, and they're only a few, but now they're covered with them. First, how do they get there? Do ants carry them there? I saw some have wings. Are those aphids? Is that how they moved from plants to plants? I really hate them.

@@amyjanefrater1447 I think it's the crazy hot weather. You too

I didn’t do well this year either bro don’t trip

Some people would spray pesticides as a solution. I don't have a solution as a nontoxic spray i can use. I was just showing people as what's eating their plant new growths. The best way to spot them in the act was nighttime. Heck no, I'm not going out there trying to catch all. Not possible.

Is your car starting burning oil recently, or has it been doing that for a while?

@@tonedubb4325 the oil burning and smoking increased over a period of about 6months, slowly at first, the last month was high, close to 1 litre per week and the smoking was high. In the end the engine light that had been on for all these months started flashing so I parked her up at home and prepared for the repair project. Engine is out now, just taken head off. All valves are black, especially far right side. The spark plug for this one is sticky black. And its exhaust manifold hold blacker than others also. Not taken valve stem seals off yet and about to remove sump to look at piston rings etc. So it’s a strip and rebuild. Going to make it a fun project. Do you want to se pics? How to send to you if so? Think I have your last vid to watch if there is one after your piston ring install. Thanks for asking friend 🙌

After removing the intake manifold, I accidentally flip-flopped the two vacuum hoses on the engine. It'd cause the engine to suck in excessive amount of oil and cause a lot of white smoke out of the exhaust. I don't believe you did that. 1. If your pcv valve is bad, that will cause an oil burning problem. Dirty intake manifold is a sign. 2. If your piston rings are gunked up, oil will come through the side of the pistons. Most likely, the case here. This happens when you don't change oil often enough. Before you go crazy with the rebuild, check the crankshaft and bearings to make sure they are in good condition. Check the cylinder walls for damages.Then, you can rebuild the engine by replacing piston rings, valve seals, head gasket, timing chain, water pump, pcv valve, fuel injector filters, serpentine belt, spark plugs, intake exhaust manifold gaskets. Buy a rebuild kit. It will have all the replacement parts in it. Don't forget to lap your intake and exhaust valves to make sure they are seated properly.

cutting the rebar was pretty quick since i got a portable bandsaw. Bending the first set was tricky since i used different things to shape it. I made a jig to bend the remainder of the rebar. I just welded and painted the frames. I think I spent about 2-3 hours bending and welding the frames together. I got someone else putting nets on the frames. That's a tedious job. Maybe she spent 3-4 hours doing it all by herself. After everything was completed, they looked nice, heavy, and sturdy compared to the store bought one. Well worthy.

@shinola228 try watch this video. See if this will help. ruclips.net/video/L2P2tUsAEgw/видео.htmlsi=1MonzpQAcVwQjix8

The fuel rail and line have pressure. You don't need to disconnect the line to get to the injectors. Be mindful when you disconnect the injector. Gas will spew out. It's best to cover the rail with a big rag so the gas spatter on your face. Clean all the injectors with carb cleaners. Attach a 9v battery to the injector plug to open the injector. You should replace all the grommet gaskets on the injector. You may have an injector that's not properly seated or gasket is bad.

@@tonedubb4325 Thanks for taking the time to reply! I just didn't understand why people would go through so much trouble to make a special tool to disconnect it at these earlier points when you can just carefully pull out the injectors using a cloth or something like you said, it's even easier to catch the spilled gasoline from there, instead of it leaking out all the way at the back there... But in case you need to take out the rail to connect it to the carb cleaner, I understand ;) I have a spare rail for that.

@billyhorton8020 Yeah.. there are a lot of cheaply made products coming out of China. They don't care about the quality. They bought parts from different vendors at the cheapest prices and slab them together, hoping to make a few dollars. While there are other companies in China that specialize in certain products, they do produce reliable goods. But since so many people produce inferior products, people associated with China produce cheap products. You get what you pay for. Lol. My mindset back then was I got a new chainsaw at a great price. Found out the reliability sux ass. I'll never buy a gas-powered machinery made in China from a vendor here in the US. The outcome will be disappointing. I ended up buying a gently used Stihl MS170 for a great price. I still own it.

@@Jes204 they won't want to take on the liability. Make more selling you a new tire with no liability.

@luismendez8241 sure didn't but I had to tried.

@@tonedubb4325 yeah, I'm having the same struggle with mine

@@luismendez8241 I did fix the problem eventually.

What was causing it?

@luismendez8241 is this engine spitting out engine codes? Or burning oil too?

@MoB-op3xq lol.. so far, she doesn't like veggies. I was eating a cucumber. She gave me that look. I gave her some, and she spit it out..

@@Moondust_857 no problem