- Видео 31
- Просмотров 5 832
scorned230
Добавлен 22 фев 2009
Vendo VT-25 cooling compressor unit
Just a walk around of a Cooling unit for a Vendo. It is marked VT25 and made by the Vendo company. The Compressor is a pancake style Techumse AP4111. Uses R12.
Просмотров: 73
Видео
Coke Machine fan blade fix early Cavalier or Vendo
Просмотров 82Месяц назад
While rebuilding the cooling unit, it spun the fan it it was wobbly in spinning. This is the simplist thing I could think of to fix it.
Stuart D10 "The Onion" slow run sloppy slides
Просмотров 133Год назад
Got it to run slow. You can hear the rod knock. There is slop in the barrel screw and where it goes into the slide for the piston rod.
Stuart D10 "The Onion" running each side part 4
Просмотров 79Год назад
This is both sides without any changes whatsoever to timing or valves, just bolted on the intake stuff. Self starts now and runs. If I unbolt the intake and go single side, it will run like the last video. If I hook up the reverse, I loose self start and lower power. Am I being too picky? I haven't run it for any length of time yet, but I don't think the one side will wake up over time. It didn...
Stuart D10 "The Onion" running each side part 3
Просмотров 41Год назад
This is the best I could get it to run in the simplest config I could. The reverse eccentrics had a spot where the flywheel felt a drag on one side, so I eliminated anything that would cause an issue. I placed the valves so the top to bottom is 1/2 inch- turned them sideways from the plans. Seems to work better. Remove the oil cups as they loosen all the time anyway. this is as of 5-13-2023. Wo...
Stuart D10 "The Onion" running each side part 2
Просмотров 33Год назад
I broke it down to test the strong side only. Taken on 5-13-2023. This engine would make a great 10v. I know that the steam chest is backward and was temporary. I was still swapping and testing both of them on the strong cylinder. I am going to post what it does with side comparison in part 3
Stuart D10 "The Onion" running each side
Просмотров 43Год назад
This is the best I could get it to run based on each side as of May 4th
Stuart D10 "The Onion" stuck
Просмотров 126Год назад
Stuck. Have to fix this or get new slides. One side will run ok, the other will not. Ordered brass to make a steam valve hoping that will work. Learned a lot about these in the past 14 days.
Stuart D10 "The Onion" simple reverse gear solution
Просмотров 34Год назад
After trying the reverse gear setup in every possible orientation, this is the simplest solution I have. I was thinking that it was reassembled incorrectly, so try try again. But, this seems to work. updates- One side cylinder still has no power whatsoever and the connecting rod slide slop has not yet been addressed. . May make & test new valves as shipping from the UK is longer than making the...
Stuart D10 "The Onion" Reverse gear troubleshooting
Просмотров 50Год назад
Observations and reviewing the video when I got it. This video is 8 days after getting it. The first mechanical problem I noticed was the eccentrics would seem tight at a certain point in the rotation If put fully in reverse at speed, locked and the bent steam valve rod. It has locked a couple of times. It also doesn't always got fully into reverse depending on where the crank is in rotation. S...
Stuart D10 "The Onion" reverse gear progress
Просмотров 25Год назад
Worked on the reverse gear. Might try the locktite 271 on the misaligned arm. Worst case it doesn't work. If I flip the arm, it won't line up either and will be to far out of alignment.
Stuart D10 "The Onion"- troubleshooting low power
Просмотров 47Год назад
Repacked all gland nuts with new material. Everything slides freely. Took cylinders off butt put pistons/bottom cylinder plate on. Checked for smooth movement of everything. Still using the original valve rods - one was bent causing issue. Straightened it and works fine. I removed the reversing gears as to eliminate all extra variables. The reverse crossbar is pinned at different angles. It wil...
Stuart D10 lower end "The Onion"
Просмотров 16Год назад
Should have put it back into the box. Started to play with it and want to fix it's issues. Will be drilling out and adding a bushing to the slides. The hole is bigger than the pin. The rods are fine on both sides. I had oil cups installed which rubbed against the crankshaft. I shortened them using wet sandpaper and they clear now. Kind of like the engine better without them.
Stuart D10 crosshead connecting rod slop
Просмотров 8Год назад
Stuart D10 crosshead connecting rod slop
Stuart D10 steam valve tight causing issue
Просмотров 41Год назад
Stuart D10 steam valve tight causing issue
Vendo H63 C to F conversion bottles to cans
Просмотров 899Год назад
Vendo H63 C to F conversion bottles to cans
Access Midstream forgery Rush Township 2016
Просмотров 277 лет назад
Access Midstream forgery Rush Township 2016
Access Midstream pipeline forgery Rush TWP PA 2016
Просмотров 157 лет назад
Access Midstream pipeline forgery Rush TWP PA 2016
Access Midstream Pipeline forgery and land destruction Rush Pennsylvania 2016
Просмотров 747 лет назад
Access Midstream Pipeline forgery and land destruction Rush Pennsylvania 2016
ECMSAS Trailbash 2010 Corum Rug Works
Просмотров 22413 лет назад
ECMSAS Trailbash 2010 Corum Rug Works
Are you able to list the motherboard they are using?
ProxMox - docker with apps in containers and TrueNas. That way you can also spin up a VM if needed
ok Thanks
I am thinking of buying TerraMaster T12-500 Pro NAS Do you recommend it to me?
Yes. I have tried the T6-423 and the T9-423, both were slow. The new version (500) is noticeably faster. 6 sata hdd's in a raid 5 and a SSD as boot. I have not used the TOS OS, I installed a Linux based NAS software. Transcodes Plex well. One important feature is that it is not loud- no vibrations, whining and no loud fan noises. Would I recommend? YES.
Thanks a Lot, Open Media Vault, Free Nas, Ubuntu server?
I have a vendor HA56E. I will convert to cans if I can get it to cool. Currently troubleshooting. What was the link to the thermostat? I'm currently looking for the compressor overload protection switch and other bits. I believe it may still work. Just curious if you have any reliable parts sources.
I dont know if RUclips allows links, but search for "Fridge Freezer Thermostat Refrigerator Cold Temperature Control Universal WPF-20". Got it from Amazon. Fun-tronics seems to carry a lot of parts.
Do you have a link to the thermostat?
can you please tell us what is the name of the item to join the bottle neck with the upper part of the skimmer?
It is a " 4 inch PVC Pipe Union". Check the outer diameter of your tubing to make sure it it the same as the inner diameter of the union.
thanks for your reply!@@scorned230
Hey there, how did you zip tie the mechanism to dispense for free? Thanks
Show more on how you made it
I bought the biggest Sedra pump with the needle wheel. Drilled into the side of the 5 gallon wide mouth jug. Drilled a hold in the side of it with a hole saw made for galss. Used 1" gate valve for output and a 3/4 " for input. Ordered a union 6" I think. The top was from an old euro reef skimmer. The wide mouth 5 gallon jug is what made it easier to connect the top I had and makes it possible to clean the inside of it compared to a regular 5 gallon one. Amazon had most of the stuff.
Cause by several issues. Sloppy slide hole where the barrel pin goes, alignement of reverse gear and originally tight valve. There were many issues.
There was one of these machines in an OLD laundromat in Coos Bay Oregon. Loved this thing! I remember it being almost Candy color on the outside. And I loved getting the Glass bottles of coke when my mum went there to wash the large blankets. Or when our house was being remodeled. When ya gona spruce it up?
You can't film the government in your own home. You can't keep property you own or pay taxes for. And they expect everyone to keep on going along while anyone from the government can rob you blind of what you and your family have built, owned or created. What a wonderful world this is.
This is how it really happens. A guy gets screwed over. And about 6 people and 6 years later? someone finds out about it. Then when mentioned in a comment section? They call you a liar? Well ain't life grand! If this happened just wants to you I wonder how many times it is actually happened over a million times before and there just wasn't anybody there to listen nor care. It's a little guy always seems to get screwed over as usual. I'm glad you found a resolution to it However it's probably been one hell of an expensive endeavor in order to do so. This land of freedom thing sure is I'm working out like it was intended by the founding fathers that's for sure
How necessary is this
NIIICE!
Nice and quiet what pump is this using?
sedra 15000. Got it from championlighting.com
Thanks, I can't find the air flow rating for that do you happen to know what it is? Been looking at doing one of these for a while as my new system will contain a lot of fish.
Nice 👍🏾