Видео

How do I build an s500 drone

I got a 20a esc and 920v motors. For some reason I can’t get it to fly. I have my motor spinning in the right way. I try to throttle up nothing seems to happen. It almost as if something is holding it back the more throttle I give 80% it almost wants to tilt over. What should I do

awesome video! I just bought one of these too, can’t wait to get it in the air!!

first

Why can’t my drone fly? I follow every step and yes my motors and props are facing the right direction

Pls Show your settings in Libra Pilot app.

hello, thank you for this wonderful tutorial . Q: How change motor spin direction without swapping motor wires?

Hello Alex. Very nice video. I would like to know in which mode are you flying in the video? I've noticed that you've det the flight mode directly on the gps. Is there another way to set the flight mode on the RC for example? Thank you

Hello, everybody. I want to connect an MG996R servo to the Pixhawk 2.4.8 autopilot without interference from the remote control, to achieve continuous angular movement of 10 degrees right and 10 degrees left. I have powered the servo from the BEC of the ESC, and the PWM signal is sent from AUX1. I am able to move the servo through Mission Planner using the Servo Output tab by adjusting the SERVOn_MAX, SERVOn_MIN, or SERVOn_TRIM values, but I cannot achieve continuous movement. Is using a Lua script the only solution?

Thomas Shirley Thomas Jeffrey Davis Maria

he soldering is not something i would recommend. i would get a flat tip and solder it first then just heat the wire until it melt into it. because those pads arent always that easy to solder on to

Roob Turnpike

All of this playlist is just pure gold. Much affection to you Alex, this is the most useful info on youtube for those drones by far.

Kuhic Orchard

Rusty Crossing

Could I use this frame for a rebuild of a typhoon q500 4k drone

where'd you get the 36 Amps/Volt? at 8:36

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

Can i use this playlist for my pixhawk 2.4.8 fc anybody answer this as soon as possible

What about if I have main 3 an ESC and main 2 and 4 with servos. How I have to connect I/O and FMU?

This is the perfect explanation and example of clear work. Thank you

Amazing video! I watched most of your videos about how to setup and fly a drone! Thanks :) Just a quick question. When you plan out the waypoints you want your drone to go to, you are using the waypoint mission tool to manually select locations. My question is, how accurate do these locations neet to be? I mean, how do you know where that launch point is at exactly, to be able to have your drone takeoff from there?

Alex, what good stuff, looking to upgrade a boat to a autonomous with telemetry what would be the appropriate setup? It really only needs one output to control direction since it's a boat on water. Throttle control would be maybe a plus but that can be done via the transmitter since the boat is still in site. Thanks John

Great stuff, really want to get my hands on the pixhawk 4, but trying to understand it as best as I can for my own project. If you don't mind two questions i got if you could help, if you know, am I right in saying the pixhawk supply's power to the GPS and receiver? (Not the USB or servo rail) Also when it comes to the servo rail, it says max input voltage is 36v. So am I right in saying I could potentially connect 3 12v car batteries up in parrell to make 36v...and then connect that directly to the servo rail with no problems?

Hello, in my case it shows package error when I give this command: sudo apt update && sudo apt install ros-dev-tools can you tell me what should i do to make this error clear???

Nice video :)

Thank you for making that very simple to understand!

Hi Alex very nice spiegazation , my question !!! My PC can't find the USB port for configuration on LibrePilot !!! how can I solve this problem? In the configuration must be all the components? I mean Controller, Transmitter, etc..

Thanks for this video! Nice and concise, I easily replaced the broken antenna on my little FPV cam.

Is there any way to upload a list of way points to QGroundCtonrol?

Where have you been lately?

This video should feature a lot more flux.

Hey, I saw your videos and wanted to build one myself like you did. I have the base, i.e. the structure of the DRONE but all the links you put don't work, can you help me with new links so I can build? Thanks.

I just want a camera on a motorized gimbal. I see the servo link, thanks. but the actual gimbal and camera, I'm at a loss as to where or what to buy. some of your links are broken. I hope you or someone can give me a hand.

I'm building a 4G drone with a similar frame. Using the frame power distribution board, I think fried my lipo. I may try with your power distribution board used here. My multimeter says my soldiers are good. Howdy, from Houston.

hello im new to work on pixhawk. i want get the barometer data how can i get that, please want help. i also heard that it has inbuilt barometer. but how to get the data..

I've been having trouble with the 'voltage divider' and 'amps per volt' values. I have a brand new 6500mah 4S 14.8 volt lipo battery. The voltage read from the multimeter is the same as what is reported by the FC. I have not been able to work out what number should go in the voltage divider, nor have I been able to work out what goes in the 'amps per volt' field... any help would be appreciated :/

Hi, can you please tell me which motors you use, the link is missing on the site? Thank you

Thank god for this guy. This was very useful

Hi Alex, I hope you'll see my comment. Thank you for the video. I am building a hexacopter using Pixhawk 2.4.8 I've finished buiding it but when i try to fly it, it does not take off. It just spins around. If you have an email address i can send you the video of it. Can you help me with this problem ? Have a nice day.

do you by chance have an updated link to the full quadcopter kit?

I have followed all the steps as shown on the video ... i am unabel to do the last step in which the safety switch is used to assign 6:42 . In my case . If i press the switch . Nothing seems to happen.

<3 Love u men ty

Hello, your video is very informative and really helps a lot. I am facing an issue with my hexacopter and I was hoping that you can help me find the solution. The issue is that when I arm and start to increase the thrust, it seems that two motors have more power than the others leading the hexa to flip and hit the ground. I have done esc calibration but still facing the same problem. I have a video but don't know how to share that to you. I will be grateful if you have any guidance to fix the problem. Thanks!

Thank you for these amazing videos!