Видео

Thank you! Our cutter came off the box and we were struggling to re-install it correctly. If using the roll outside of the box, don't cut the tape flush. Instead, leave extra length of backing beyond the filmoplast. This makes it much easier to separate the backing from your next piece.

Is there any easy way by manually bending that consumers can get the bowing out of the sides of the boxes?

This was amazingly interesting. Watched the whole thing. Lovely to see the expert persnicketiness behind these products.

Lovely to see the behind the scenes, you always wonder if it is just a warehouse. but you do the whole thing, thank you. Charles

are museum boards like the backside piece of the framing? I have found no thing called museum board in my country help

I use these boards as a substrate for my art work. I love working on it with colour pencils as well as graphite pencils. The only problem I run into is removing unwanted marks from my colour pencil off the board. Like when I accidentally drop the pencil or smudge pencils where I want it to remain white. Do you have any tips on what makes the best easer for this. I’ve tried a few types but can never get it off. When using this as my substitute instead of other cotton papers there’s no room for mistakes or accidents. Would love to know if there is anything that works extremely well at removing a dot/smudge of pencils! Thank you

Can you please guide where to find this archival sheets and box for preserving magazines

Also what would be the best storage media to keep scanned copies of them too? I know that some things can be really expensive like certain tape drives then there are DVDs and hard drives. I would highly recommend scanning them all in TIFF format in a very high resolution. Got a scanner that can do 4800 DPI and not just for small things like photos? Use it! If you are worried about the space these files take up just realize that they are often compressed but with a lossless algorithm like LZW and not a lossy one similar to JPEG which is known to have some artifacts which can reduce the quality of an scan or image if there are too many of them. Make no mistake, JPEG is great for allowing fairly quick image downloading but when it comes to preserving ALL the detail use TIFF. What would we do if Aldus (now bought by Adobe) had never created the TIFF format? I guess we would be using the BMP and PNG formats more. I am no artist or expert but I do know at least all of that which I just mentioned.

6 years and no comments lemme fix that

Thanks

I am looking for 21 x 34 cm sleeves for large documents. any suggestion where i can find ?

where can i buy sleeves like this in europe ?

Would this box fit a quilt? Charles

Hi! I can't find any information about the metal edges used on archival boxes anywhere online. Can you buy them separately? What kind of tool is used to crimp them on boards?

😊 𝙥𝙧𝙤𝙢𝙤𝙨𝙢

I have a 1958 program from somewhere I got on eBay and a 1969 harness racing photo, what's the best way to store them?

Are zip lock bags acceptable as a substitute to the archival polyethylene bags?

Video starts at 1:15

"Put in polythene bags and in acid free boxes". You're welcome.

I have to sale old letter of Gandhi ji famous leader of India but how and where I don't know please guide me

The insertion of the back plate and tapped corner is not shown, you see only the finished assembly. You put the back plate in first, be careful the free end points in the right direction, then the tapped corner. You may need to back the screws out a bit to get the tapped corner to go in. The back plate has a 'B' on it and the tapped corner has an 'A' on it. The letters should face each other. You then drive the screws in to force the plates apart to grip the frame from the inside. There are only two screws in each tapped plate, the narrator says four, he is referring to the two corners of the bottom rail. You do not assemble the fourth side before adding the Omni Hangers for the wire. They must be slid into the channels on the two side rails from open ends. The Omni Hangers do not just tip into place, they must be slid under the rail on both ends. You do not put the Omni Hangers on then put the wire on. The Omni Hangers are put onto the frame sides and a proper length of wire is fit. Start by bending over about 1 1/2" of wire and hook it into one Omni Hanger. Bring the wire across to the other Omni Hanger and adjust to the slack that you want, then bend the other end over at that point and cut the free end off at about 1 1/2" length. You can't twist the wire properly when it is on the frame; you must take both Omni Hangers off the rails. At each end, grab the two wires between two fingers, or between the faces of a spring clothespin, and twist the Omni Hanger until the free end of the wire is completely twisted around the standing end. Then do the other end. The wire must be free to rotate, so it can't be attached to the frame. Once both ends are twisted, the Omni Hangers may be slid onto the side rails. Then you can insert the picture stack and attach the fourth side of the frame. You may not need the spring clips. The combined thickness of the glazing, mat, picture, mount board and Foamcore may be a snug fit. Check the dimensions of the materials to be sure they will fit within the channel. Two of my four, supposedly identical, stacks would not go into the channels until I compressed the edges of the Foamcore by pressing it with a block of wood. If you use 1/16" thick board for your backing, you will need the spring clips. There is a trick to getting them in. You slide one end under the rail, depress the center and push it in, then, while holding the center down with one screw driver, slide the other end in with another screw driver, holding the face against the back board to avoid gouging the board.

Good idea.Still we have some questions.Pls send your email

I am in the understanding that unbuffered paper was the best to use with photography?

Great to see that... I made it too. Using woodprix handbooks :)

Im sure you can build it too guys. Just look for Woodprix page

I talk with some archivists and they told me that ANY kind of plastic (mylar, poly... etc.) is not good for paper, is better use other papers like ones that you have.

storing of diecast toys should use which?

Is this johann sebastian bach?

Great to see that... I made it too. Using woodprix handbooks :)

I check a lot of woodworking handbooks. These one from woodprix are the best.

Was wondering won't the polythene bag cause condensation? Can't I just put them in the boxes? Thanks

I can make it myself. Just got instructions from woodprix website and I'm ready for do it :D