Thanks you 2023 here 12k on it already needs, one blaaaa. that sucks, can't seem to keep dust out of cab either. Have to wipe dashboard off like every day.. 😢
Another piss poor set up from Peterbilt - If you open the hood, on the passenger side cow, you can see the filter under a cage..Why didn't they make it so you can open the cage from the outside to change the filter, instead of taking the inside apart, and wasting your time. Wake the hell up Peterbilt.
Had a 2007 Peterbilt and the cabin filter really sucked went down dirt roads and totally sucked fine dust into the cab hated it. Peterbilt cabin filters truly suck very poor design period.
@@louisadamramos i found out by myself, it is super easy i removed the 4 bolt behind the plastic around the mirror arm, and unpluged the electric connector, and that it, i bolted and plugged the mirror assembly back on
Truly needed this vid. I was almost about to lose my safety bonus and almost paid the TA 128 dollars an hr to fix. Luckily my insert popped clean out and I was able to reinsert in under 5 mins..
But be ready to damage the hell outta your maintenance account. Might as well get new engine mounts, flyweel resurfaced, transmission input shaft replaced along with fluid change and carrier bearing replaced. All is not necessary but if you can afford it do it.
Thanks for taking the time to make this video but im cringing watching this seal go in as it appears one of your pilot studs must be longer than the other two as the nuts are not being drawn evenly but with enough pressure it seats straight and im only hear because i had a clutch installed and now the rear seal is gushing oil and the reapair shop say its not there fault u drive them into the dealer and u toe them back out after u pay the bill.
Bueno Días me puede desir cómo encuentro el número del motor de un prosta
This is the worst design for a cabin air filter replacement I've ever seen.
Thx
Gracias amigos por compartir su conocimiento ya logré cambiar el filtro
My ac not working on 2023 peterbilt 567. Compressor and clutch are working. No power on ac fuse. What is the problem?
2010 389….. filter takes 30 seconds to change
Already helped me a ton thank you, going way too fast tho
I drive a 567 and my cabin filter is right next to the firewall under the hood I wonder if I have another one behind the glove box?
Nice Video, Thank you
Finally found a video. This is the same setup of my 2019 pete 579. Thanks man, i've been looking for this video for a while.
Thanks you 2023 here 12k on it already needs, one blaaaa. that sucks, can't seem to keep dust out of cab either. Have to wipe dashboard off like every day.. 😢
I guarantee Peterbilt shop would charge $800.00 Labor to change this filter smh
Same on Kenworth trucks Paccar Not good
👍🤝
Another piss poor set up from Peterbilt - If you open the hood, on the passenger side cow, you can see the filter under a cage..Why didn't they make it so you can open the cage from the outside to change the filter, instead of taking the inside apart, and wasting your time. Wake the hell up Peterbilt.
Had a 2007 Peterbilt and the cabin filter really sucked went down dirt roads and totally sucked fine dust into the cab hated it. Peterbilt cabin filters truly suck very poor design period.
Good job it'll healf me thanks
Great very
Great very nice
Perfect! simple video. Thank you
Thanks for the video. I drive a 567 roll off and it doesn't blow good on recirculate. I'm gonna down it now and change it. Thanks.
Good job you save lotta time for us thank you❤
You didn’t show how to put it there which is this is the hard part that’s not helpful at all
Damn Bro you made that look easy 👍🏽
LoL we have a lot of these trucks I have replaced about half of the fleet thanks for watching
Do i need to remove the inside door panel on pete 567, i need to replace the whole mirror assembly i hitted a goose at 65 mph
That's too bad. I haven't gotten that far yet so I really don't know how to take the whole mirror off
@@louisadamramos i found out by myself, it is super easy i removed the 4 bolt behind the plastic around the mirror arm, and unpluged the electric connector, and that it, i bolted and plugged the mirror assembly back on
Nice video friend! A question! How much should you tighten at the end? Or only until the tool stops with the bel housing?
Truly needed this vid. I was almost about to lose my safety bonus and almost paid the TA 128 dollars an hr to fix. Luckily my insert popped clean out and I was able to reinsert in under 5 mins..
Great content definitely saved me some money today. Thanks 🥂🍾
My passenger mirror shakes but not the others can it be loss or something?
You might be able to pull it out and tighten the screws on the motor behind the mirror
Thanks I needed this my shop said they need to take the back off to get mirror removed
Does it work the same way on a 2006 peterbilt 387 on the mirror replacement
I don't think so not sure I have not worked on an 06
Cambiar retén de cigueñal motor 300 mak
Does the engine have to come out to replace that seal?
Nope, just got to pull trans, clutch and flywheel.
But be ready to damage the hell outta your maintenance account. Might as well get new engine mounts, flyweel resurfaced, transmission input shaft replaced along with fluid change and carrier bearing replaced. All is not necessary but if you can afford it do it.
Where do you get the seal installer?
You can find it on eBay also Rush truck center
louisadamramos would you happen to have a part number for it.
Cummins 3164780
Thanks for taking the time to make this video but im cringing watching this seal go in as it appears one of your pilot studs must be longer than the other two as the nuts are not being drawn evenly but with enough pressure it seats straight and im only hear because i had a clutch installed and now the rear seal is gushing oil and the reapair shop say its not there fault u drive them into the dealer and u toe them back out after u pay the bill.
@tim quigg did u have the rear seal replaced while they were changing the clutches?
@@Thillx2 no
Wow that is a really Big Toolbox!