Видео

You're a life saver. Roland just ignored me when I enquired. Found this and managed to bring my CY12 back to life with this process. Works just as shown. Thanks!

I wouldn't be cutting the cymbal like that, pretty sure you don't have to, unless the CY-13 has some unique bracket design that is different to the CY-12 and CY-15? Word of advice - aerospace 303 spray, get it inside and it will help lubricate and protect the rubber to prevent decay internally. This will drastically reduce the wear which occurs from the friction between the rubber surface and the plastic housing/membrane. If you destroy a membrane you can get replacements from Myrk- Instruments, though they are not specifically designed as replacements they can fit with modification to the cymbal (as roland won't sell you a replacement membrane).

Extra super good job thank😀👍

Muy útil!!

Thanks for the video. My cy13r was self choking and by opening it up a little bit i could see not only debris but the sensor ribbon is cut. Amazingly it still works cut in 2. Now my problem is to fix all the back cracked plastic.

Somehow it took like 7 years for one of mine to start having this issue, maybe they made them better back when I bought em or maybe I got lucky, I bang the hell out of these Mine was so old and used that I didn't even have to cut the rubber in the main hit area, it was just already mostly crumbled and it peeled right off. Some of the plastic was cracked and I had those rubber pebbles on the inside, I could even see where they were triggering the choke because it rubbed black on the sensor. Works like new again, thanks!

Started having self-choking problems with my CY-13R at my last gig. Found this video and Viola!!! Works like a champ again. Thanks so much for posting video!!!!!

Bro thank you. I was about to spend 200 bucks and found your video. Legend

Fixed my black bottom CY-12C model cymbal. Thank you for making this video sir!

I have one of the white bottom CY-12C and this method corrected the self-choke problem. In my case, there were two large chucks of rubber that had broken away and were siting on the sensor edge. After I brushed off the sensor edge the choke problem was gone:)

Great video! I have a 13C that is choking. The Ride cable works and allows some ride/crash. The Ride Bell cable doesn’t work in either jack. I thought it was the cable but I bought a new cable assembly and the new Ride bell cable doesn’t work either. Anyone else have this problem? Thanks!

Вы его просто почистили или заменили Датчик?

Just saved me 200 dollars

Would this work for mine ? It’s a cy 12 C. It’s very quiet and have to hit quite hard to register slight sound

Well i guess im buying Efnote. I was just about to pull the trigger on a roland vad507. Fuck that lmao

Great video! One of my ATV-cymbals is stuck in choke. I will try this as I think they are much the same with some people from Roland working at ATV..

If you’re angry about paying for e-cymbals then wait until you buy acoustic cymbals. Is hard to make anything that can stand up to constant whacking.

Thanks a lot buddy! That was exactly what i was searching for! Gonna fix it tonight an beat the hell out of it again 😅

This method is excellent! I have the same problem on a Roland Cy-18DR ride cymbal. Could this solution work?

I love the ending lol

Left hand drumming goes hard 4head

Any reason to glue the edge back down?

Thank you.

You just saved me £200 thank you very much Sir! 😊

This is an excellent video thanks. Worked a treat.

bought my kit in 2020 and this trick definitely worked great on my broken 12c. thank you so much for this!

This method fixed my CY-5 too, thanks!

Opened mine to find rubber like in the video but the white disk had been cracked in 6 different places with chunks ripped out of it. What a mess. Going to try using some RTV to hold the pieces in place and come up with a way to re-enforce the disk.

I always loves the drums on this song so much. Especially the closed hi hats

I'm considering upgrading my cymbals to this CY-12C. I see that Roland has a new version though, that is thin, and I'm wondering if this thin version fixes the problem that you are describing here and if not, if the thin version can be fixed in the same way you are doing the fix to this one?

I bought a Roland kit a few months ago and everything worked fine until recently. This is my first kit and I have very little experience with troubleshooting issues. I have the cy13 r and when I strike the bell area now it causes the sound to become scratchy and distorted with all the cymbals and drums. I have to strike another cymbal several times to get the sound back. Do you have any advice or suggestions on how to fix this problem? Thanks

before cutting your cymbal check that firmware is updated on your drum module. i almost cut my cymbal and found that firmware fixed my issue. i had pitch issues on my ride cymbal edge trigger before the update.

Thanks for the video. They are so damn expensive. Mines even the plastics and the long flat sensor have broken. Bad bad quality.

My Cy-12c on a TD17-KVX stop triggering on edge/rim. Im out of warranty. What you suggest me to do?

one more tool in the arsenal

따봉

This was very helpful, I've recently had the same problem with a yamaha dual zone pad that's worked fine with a td17 module and then suddenly the choking problem.... I'll have to figure out how to get the rubber off but at least I know the fix now, thank you 👍

I have the CY-12c, and I did the same procedure to solve the problem. Internally it was very clean, without any foreign particles. Anyway clean them. In the end the problem persists. If anyone has managed to solve this problem, please share the solution.

Worked for me!!!! Saved 400 on a new cymbal. Thanks dudeeee!

I absolutely love you bro, this worked like a charm. 100% agree with everything you said at the start aswell!

Aveeeee

Nice to see other left handed drummers :)

Thanks for the tip. Love the ending, lol

What a great video, I’ll know what to do when my cymbals stop working now. We need a lot more competition in the electronic drum market…

Hi boss nice drum...i just want to ask how did you setup to make it left handed?

Roland is a joke

Marcelo vc é brasileiro??? Mano, preciso de ajuda. Meu prato parou de funcionar o bell. A cupula, ate cortei o cabo achando ser ele, do RDb. Meu modelo é CY-13 r Td 11 kv

Mine its similar CY 13 the bell its not working

This is excellent advice. I talked to my Roland rep & he suggested a $500 plate. Peeling the rubber back & periodically cleaning fixes auto choke especially found on my Silver Cy14 rubber models, on the top of the frame. Those models are easier to separate just take your time. CY14 Silver isnt glued and is easier to peel the rubber.