Видео

Tak penah pakai 4S bang. Tapi rata2, 6S mmg akan rasa lagi power dari 4S...

@ ohh sbb sy masih pakai 4s baru nak try pakai 6s tu nak thu power dia jauh beza je mcm mana.. ok bro trima ksih

Thanks bro!!!

It was recorded via the V2 goggles (the Vista doesn't have on board recording for video nor audio).

Thanks bro!

Thanks bro!

@velocistafpv you're welcome!

Thanks bro!

I'm just using SupaFly's preset for 3.5" bro.

I'm using GEPRC SpeedX2 2105.5 bro

I'm thinking of doing a video soon once I'm back from work travels. Keep a look out on that one! Cheers bro.

@@velocistafpv this is nice, need tut :D

Angatkat satu brooo

Thanks bro!

Ntah. Aku kelam kabut je bila powerloop ngan natang ni. Maybe sebab pilot tak biasa bila loop tu takde momentum sbb ringan sgt. Hahahahaha

Tq bam!

Cincai slap together one. Hahahahaha

Thanks bamfu 😘😘😘

Tomorrow, joms fly bro!

Thank sbro!

Thanks bro!

Thanks bro!

We're going again on 21st Oct Monday morning bro. Joms!

Thanks bro!

Thanks 😁

Thanks bro!

Thanks ✌️

Thanks ✌️

The AIO was only there to provide arming signal to the O3 and OSD (OSD can be customized in Betaflight) and do not control the plane at all. The BetaFPV 14Ch receiver is ELRS, therefore u can set it in the configurator to output Rx and Tx via 2 PWM channels. These two will then connect to the AIO providing the arming singal to the O3 via the AIO. Plane control will still be via the 14Ch ELRS in PWM.

@@velocistafpv Thanks 😊.

Thanks man! Ur one of the reasons I'm getting into tinywhoops!

Thanks bro! Taking a break from FPV now. Will be a while until I come back to Bolehland.. sob sob.

@@velocistafpv ehhh where to ma bro?

@@CurlyFPV Singapore for work bro. Will be back this Friday for two weeks. Hopefully can find time to fly. 😅

@@velocistafpv ohhh ok la sg can still fly there ma. See this weekend wanna fly or not bro.

It is quite simple really, just need a 3D printed mount that replaces the stock one on the antenna. Will be making a video out of it but would need to wait as I'm travelling for work. Cheers bro.

Thanks!

Aritu pi Kota Puteri tapi tak jadi maiden. Canard problem huhu.

Thanks mate!

Thanks mate!

Thanks bro!

I listed all the parts in my video maidening the VX3.6. Only difference now is I replaced the TBS Crossfire with ELRS. ruclips.net/video/sLCI7ntfsbo/видео.html

Thanks dude! How does the 1300mm and 1700mm compare? I'd like the 1700mm but hangar space doesn't allow it. Lol

That is actually a Radiomaster 2.4G Moxon directional antenna which gives higher gain. I've sinced removed the Moxon antenna and modded a Radiomaster Pocket antenna to fit the Boxer. I don't think it is better in range, probably just similar. Reason to put it on is because it is foldable and need not be removed during transport. This short video shows my newly moded Radiomaster Pocket antenna on the Boxer. ruclips.net/user/shortsdQGbR9FXc1o

@@velocistafpv noce 10x for the info

Tinywhoop yuk! 😘

Sebenarnya hobi lama ni.. main zaman uni dulu.. 🤣🤣🤣

Tq abam sifu 🙏🙏🙏

It's the GEPRC one, bought from my local FPV shop. Love it! geprc.com/product/geprc-sponge-foam-padding-for-dji-goggles-2/?ref=9p2tznso

Thanks dude!

Thanks for the compliments dude! Fixed wing beckons!

Thanks for the tip. I'll try that!

The OSD comes from a Betaflight based flight controller (I'm using an AIO) which the flight battery powers both ESC and the AIO. My BetaFPV SuperP PWM receiver gets power from the ESC and is connected to the AIO via RX and TX wires which in turn is connected to the O3 Air Unit to give it the arming signal (hence full power to the O3). I'll be making a video on the setup once I have the time.

@@velocistafpv Dang that sounds complicated. Really good job on the setup. A video explanation on how the OSD and wires are set up would be amazing.

Thanks ✌

sedap sehingga menjilat jari kata omputih brooo.. 🤣🤣🤣

Thanks for the sub!

Thanks for the compliment bro!

Thanks ✌