Видео

So the bike is fully working with no problems, only problem is the screen?

video too bana dali per bataye hi nai kya mix kiya😂

Display settings-P7-001. Check your settings😊

What a pointless video

Ομορφιεςςςς 😎😎

Can you put an update video?

Καλησπέρα τι ώρα γίνεται περίπου το κάψιμο?

Thank you very much for promoting our brand. Can we cooperate with you?Can you leave your contact information?

why does the battery switch from 2 different graphs?

hi) How can I disable the assistance in the settings and only leave the gas accelerator enabled? Also, what is the PIN code to access the P2 and P4 menu options?

We love Shrimps ❤❤❤

It's unfair to run all 3 tests at the same speed/power/focus settings. Just because the wood base is the same., the treatments you applied has efffectively created 3 different materials.. Have you tried changing the focus on natural wood? It's amazing that you can get quite a dark engrave with some diode lasers but it does depends on the focal length of your beam..Your "conclusion" is really an obsevation from the limited testing you carried out....... and they are perfectly valid. I twould have been more useful to explain why the differences . Wood is an interesting material made up of two main components, each with its own chemistry and damage threshold. The main component , cellulose, is a soft material and easily damaged by heat. It is encloses in thousands of porosus tubes of lignin (imagine fish net tights) . With untreated wood you are effectively vapourising the cellulose and scorching the more heat resistant lignin tubes. Add baking soda and the metallic salt in the compound, better absorbs the light energy. It still vapourizes the cellulose through the "fish nets" but better light absorption creates more damager (scorching) to the lignin. Borax is a completely different process . The Borax coats the "fish nets" and when you heat it the cellulose again vaporises but this time the heat turns the borax back into a fish net exoskeleton of boron. a black shiny metalloid substance . That black exoskeleton is very fragile and only dusty if you brush it and damge it. As you have seen for yourself , Borax gives by far the best results BUT you can add strength to the fragile black exoskeleton by spraying the finished engraving with a clear acrylic varnish. For food applications such as chopping boards boron is not toxic, It is found in many fruits and vegetables. Equally baking soda (sodium bicarbonate) is not toxic but produces more dutrable engraving. Both require surface protection if intended for regualr food use.. In effect what you have demonstrated with your test is that for the same parameters . 3 different materials absorb that light energy with different efficiencies.

Talking instead of music would HELP.

VELIKO HVALA,ZA UPUTEALI MOLIM,PREVOD NA HRVATSKI ILI SRPSKI JEZIK!!LIJEPI POZDRAVI IZ BOSNE IHERCEGOVINE!!!!!!!!!!

Oooooo yes🎉🎉🎉🎉🎉🎉❤❤❤❤❤❤😮😮😮😮😮😮

mas bien parece que tu prpblema es el display

mi mx03 tiene 1500kl y va genial.

How is the bike working now? I ordered one picking up next week

The odometer is not updating either. So I presume somewhere there is a sensor that counts the rotations of rear wheel and that is used for the controller to calculate distance travelled and speed. So could there be an intermittent failure of a cable of connector between rear hub and controller? If you change the display to show power output from the motor, does that show zero or the correct reading? I doubt it would be the hub motor as that is not a constant speed.

The brake makes squeaking noise. I read this often during tests of Chinese e-bikes. Sometimes it becomes better changing the brake pad (othe rmanufacturer). Is the suspension on the rear ok ? Or does it made the riding instable ? Can the supsension be adjusted ? Can the steering rod being adjusted in the height? What about outdoor temperature during your ride ? I really hope that you receive support from Shengmilo.

But i think it likes getting root bound

1:30 watch out for pedestrians

Have you received the new controller? If so, how is the bike doing? Many thanks.

Hi , how many miles is your mx05 doing please , I just got one and getting 20miles on P3 pedal assessed 👍 thx John

How fast does it go?

금전수는 알뿌리 식물이라 흙의 물빠짐이 좋아야 하는데 펄라이트를 섞어서 흙배합을 잘하신것 같아요. 물주기만 조심하면 사계절 짙푸르고 윤기나는 잎을 감상할수 있겠어요. 영상 잘봤습니다. 😄

caption is to fast

What wattage is the laser? At 8500 mm/min that's really high. My 5.5 watt ortur pro 2 won't do anything at that speed.

Good to see your wearing gloves, chopping boards can be dangerous

А на русском языке можно же писать.

How deep is the engraving?

thanks you man. From Dominica Rep.💪

Very nice video and thanks for the tip with also using orchid bark in the soil, good idea!

I would have taken little side shoot off and put in water to grow a new plant

Thank you

What grit paper did you use when sanding?

Finally, did you make money from engraving?

Where did you get the boards?

Great video. Whats a good source for these cutting boards?

Nice one ... we want more..

That’s very interesting

For engraving on wood NOT used for food prep, I use borax before, and acrylic spray after. How does one preserve the engraving's DARK COLOR on a cutting board intended for food? Are your boards decorative, or for food prep? How did you keep it from smearing when you applied oil?

what kind of machine did you use.

Not much info here .

How long does it take?

Hmm ...a slight mistake with the speed I think. Not even the fastes CO2 lasers with 200 watts are capable of 9000mm/SEC. Divide this by 60 for a diode laser and you get a realistic speed of 150mm/SEC = 9000mm/MINUTE

What is the airflow of that aquarium compressor?

Thanks for the vídeo. Where do you get these bamboo boards?

Which oil you apply after engraving