Видео

I see serious issues!

That better be more than 1/2 inch osb! We in the old days used one inch thick plywood! The other concern is lifting!

Dude youre the man for posting this bout to do the same thing for my 2008 f150

So what is a meter loop? The whole thing put together?

Your camera lens is dirty making it look worse than it is 😅 also the print of your nozzle isn’t dialed in, see the line on the side? By the way this machine is amazing for the money, just on a wait to receive mine.

that's a cool system

My arms hurt just thinking about all that work

Well done!!!!

You butted your wailers end to end? NO stagger the joints for straighter walls

Wow.....

NICE work!!

I don’t see any toe ties to footer you either shoot 2x to footer and screw bottom form to that both sides or there’s clips you can shoot down with a slot on each side and a screw hold the most pressure is bottom and ties +12” not enough and doesn’t prevent lifting

Osb is not plywood

0:19 yes they are much faster. It would take one day to put them all up. Even a project that big.

Just rent wall forms from somewhere. The cost will equate to the time you’re going to spend building this. You’ll be able to do another 3 projects by the time you’re poured out. They’re a lot more sturdy too I’m sure.

Did it work out ok?

Very good, its an excellent work !!!

Thank you!

Nice Recommendation!

دروود آیا قالبهای فلزی آماده برای اجاره کردن نیست ،خیلی راحت‌تر است

Did you by chance do two lifts (two pours?). The risk there is a cold joint if it didn't get consolidated well between top and bottom or timing was too long or something surfaced on bottom lift while it bled that interfered with the top lift mending. Look for any kind of cracking along a potential cold joint. Consider internally vibrating briefly between lifts to integrate them properly - and shouldn't be longer than 15 minutes normally.

osb lmfao there is gonna be a blow out ! you need 3/4 form ply

23 months? WELL DONE!!!! May I ask how many acres the house and the area you cleared (looking at Google)? My project had to take a pause but is about to begin again as I put a perimeter fence around the property in January. Once that is in, THEN I can really begin.

Hi what’s the spacing between the snap ties Thanks

agree

Way to go! You must have very low clay soil! Well done. Its all coming along fantastically/!

WELL DONE! YOU DID IT!!

I see concrete busting that particle board, how did it go for you? Also see you didn't use any long tail snap ties or form liners. Let's see the finished product? Not hating, at least you are trying something. Curious how it turned out. You should have also staggered the 2x4s to lock the sheets across the seems instead of butting them at the seems... That will separate in my experience as a carpenter. Concrete is heavy and doesn't have forgiveness when it goes. Hope you poured slow. Best of luck 🤞

No hog troughs? Those whalers need to overlap to lock those corners in. I see a blowout

Where’s the plate?

Where I am you need to have a shower pan inspection, fill it with water 1/4" from the top of curb, and let sit for about a day, I think there is a minimum depth too.

Can you reuse the osb for other concrete work?

Partical board. Ouch, better hope it doesn't get wet.

ICF

Did you have any problems with blow outs or bulging

How did that 24" OC work out for you? I'm doing a 4 ft frostwall and I'm a little concerned the spacing might be too far apart.

What in the F are you doing you have no clue.

Nice job. Do you have any vids showing how to put forms together with the snap ties?

Well done!! Are you a tradesman? Your work is very strong! You mentioned the trusses as a "system". Could you please provide a link to where you got those?

That does not look like plywood. That looks like OSB.

I spent years working that system. If you have access to a forklift or excavator, you can gang the set up and after initial set things go much faster.

Looks to only be 6” thick is that right ?

Don't see any strongbacks in that wall

You turn the clips at a slight angle and put an #8 penny nail half way in and bend it . This prevents the vibration of the concrete to cause the clips to fall off. Also stager your 2x4s by 4 ft and break the joints on a clip.

Add a keyway or rubber water stop in the concrete footing while pouring. Have done this many times on commercial jobs of wastewater plants. If the wall is poured on a flat finished concrete footing it creates a cold joint which water can seep thru.

OSB plywood???

lol

Man, ICF would be amazing in this instance. Have you considered it?

👍👍👍👍👍👍👍👍

if your using short end ties it’s better to use burke clamps because you end up using halt the 2by 4