JC's_DIY
JC's_DIY
  • Видео 1
  • Просмотров 89 488
Lexus GS300 (2002) Catalytic Converter and Exhaust Manifold Replacement
Error codes P0420 and P0430 suggest the catalytic converter is going bad. In states like Texas that use the vehicle computer error codes for emissions testing, a vehicle presenting these codes with a check engine light (MIL) are sure to fail. This is an expensive repair for a Lexus, so it is definitely cheaper to do it yourself. This videos shows how to replace the entire exhaust manifold with the catalytic converters.
Просмотров: 89 497

Видео

Комментарии

  • @piffy.4532
    @piffy.4532 5 месяцев назад

    Would bad cats cause a gs300 2003 Lexus not to start?

    • @JohnPColbert
      @JohnPColbert 5 месяцев назад

      It's unlikely that your cats would stop the engine from starting. Certainly, a completely clogged exhaust could prevent the car from starting, but it's unlikely that the cats are completely clogged. I would definitely check for other trouble codes to see if they can provide a clue for why the car won't start. The car will run with P0420 or P0430 codes.

    • @piffy.4532
      @piffy.4532 5 месяцев назад

      @@JohnPColbert I just bought the car the other night it’s been starting fine. It would hesitate a little bit from a stop and if I gave it a bunch of gas but besides that it ran smooth. Now it doesn’t wanna turn over. I got it starting after I unplugged the mass airflow sensor, it ran rough then died after a few seconds, I’m on my way as we speak right now to get a scan tool. I’ll update you.

    • @JohnPColbert
      @JohnPColbert 5 месяцев назад

      @@piffy.4532 Please check the intake resonator. It is the part of the intake tube that sits between the Mass Airflow Sensor and the Throttle body. It's a black plastic box in a slight S curve shape with a metal heat shield on the bottom. It sits directly over the exhaust manifold. These resonators are notorious for cracking. It happened to me. A primary symptom is hesitation when starting from a stop. The crack lets air in after the MAF, which throws off the whole system. The resonator is very easy to remove, but be sure to actually remove it, because the cracks, even when they are large, are hard to see. This problem can cause misfires, hesitation, damage to your cats, and emissions trouble codes, so it would be good to give it a check. BTW - you can use some metal ducting tape to temporarily patch the crack until you can make a more permanent repair.

    • @piffy.4532
      @piffy.4532 5 месяцев назад

      @@JohnPColbert I checked it this morning and it doesn’t have any cracks or holes. I’m starting to think it might be the fuel pump because when I would give it, gas would a heavy foot it would sputter, and then takeoff, but if I would ease into it it would dry fine and it died on me driving up my hill on my house so I’m gonna point all fingers to that because besides that it was running fine

  • @rambleblaze
    @rambleblaze Год назад

    you the goat

  • @outtheframe5713
    @outtheframe5713 Год назад

    Dammm you did a great job. I have a black 2002 GS 300 I’ll pay you to fix mines let me know if you up for it you can shoot it for one of your videos

  • @XqeDiosxqe
    @XqeDiosxqe Год назад

    What was the initial bolt measurement? Under the car exhaust.?

  • @shakky9749
    @shakky9749 Год назад

    if anyone wants a work around to getting a new cat, take the cats out, if theyre clogged, drill bit the inside out (technically catless now), then get o2 sensor extensions and u should be good.

  • @wong7713
    @wong7713 Год назад

    Thank you my man! I’m doing this tomorrow and this definitely is going to save me some time!

  • @hippieP
    @hippieP Год назад

    Are these dormans

  • @extarthe
    @extarthe 2 года назад

    This is super easy compared to most cars wow

  • @IS3000vato
    @IS3000vato 2 года назад

    AWESOME. I'm about to do this on my 2004. I wish however that you hadn't skipped too much on the heat shield transfer. I'm hoping it won't be too difficult to do it. If anyone has a good video to figure out how to do it step by step, that'd be great

  • @sohclovis9676
    @sohclovis9676 2 года назад

    Thanks So Much for all the explanations, they are so usefull

  • @stevequan1135
    @stevequan1135 2 года назад

    Where did you buy this?

  • @PatrickHenryLibertyorDeath
    @PatrickHenryLibertyorDeath 2 года назад

    Very helpful but I had to shift the engine a bit on the Is300 to get the old one out and the new one in. Used the rolling jack with a block of wood on the oil pan.

  • @MRMAN-wb1tv
    @MRMAN-wb1tv 2 года назад

    *You missed putting the anti ceasing goo on the o2 sensors* 😨

  • @scott-michael812
    @scott-michael812 3 года назад

    I live in Ny soni need a carb compliant but my question is you noticed any metal shavings inside the runner. I see this videos 4 years old but if you could answer I'd appreciate it.

  • @real_ultrajoe
    @real_ultrajoe 3 года назад

    2jz

  • @frankcastle9658
    @frankcastle9658 3 года назад

    Hey bro how’s the catalytic converters holding?

    • @jcs_diy26
      @jcs_diy26 3 года назад

      They're holding on. I must add that I was lucky to find, shortly after this repair, that my resonator box had cracked, which was probably the cause of the cats going bad in the first place. It turns out that these cars have problems with the resonator boxes cracking, which allows air into the system after the mass airflow sensor. This leak throws the air/fuel mixture off that causes problems for the cats. In my case, the crack was about 6 inches long under the metal heat shield at the bottom rear of the box where it couldn't be seen unless you pulled it out and inspected it. I wonder if I had noticed that before the original cats failed, if they would still be on the car. No way to know, but it makes sense to check the resonator box.

    • @frankcastle9658
      @frankcastle9658 3 года назад

      @@jcs_diy26 thank you so much for the response! I bought a gs300 1998 with 114k miles for 1.5k pretty clean but only problem is they took the catalytic converters out before i noticed. I was just wondering what is a good company that will last me. I appreciate your help!

  • @nufsedsaynomore
    @nufsedsaynomore 3 года назад

    1999 Lexus G300 with over 300k miles. Noticing power lost on performance and it fails smog test. How reliable are the aftermarket catalytic converters? OEM are impossible to find and some are charging like 8,000$ on Offerup. Thanks for sharing the Gospel!

  • @jdagreat4595
    @jdagreat4595 3 года назад

    Can i change the manifold gasket without removing the whole unit

  • @FernandoCastro-rg7wi
    @FernandoCastro-rg7wi 3 года назад

    Will this work for a 2003 Lexus gs 300 ?

  • @zefdin101
    @zefdin101 3 года назад

    Thanks man, this is a HuGE help for me. Much appreciate the breakdown! Awesome job, smart, easy to follow, just the needed info and helpful tips. You are the man!

  • @ImpalaSS08
    @ImpalaSS08 4 года назад

    There’s a rear exhaust CAT on these cars too, does that have to be replaced too?

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Hi Mark. If the front cats broke apart, then the cat material will clog up that rear cat. That can cause a significant reduction in performance. If you're just dealing with the trouble codes and the front cats look fine, then you don't have to change out the rear cat. If cat material is breaking apart, you will hear it rattling when you shake the pipe (off the car of course) and you may even be able to shake some material out of the pipe. In that case, it would be wise to replace the rear cat. The O2 sensors that are reporting the trouble codes are placed in front of the rear cat, so that cat converter has no bearing on the 0420 trouble code. I hope that helps.

    • @ImpalaSS08
      @ImpalaSS08 4 года назад

      I was not familiar with the Lexus and that totally makes sense and answers my question. Thank you so much for your insight with dealing with these cars.

    • @jcs_diy26
      @jcs_diy26 4 года назад

      @@ImpalaSS08 No worries. Glad I could help. I hope your repair goes perfectly. Remember to check the resonator box for cracks. That may be what lead up to the cat failure.

    • @ImpalaSS08
      @ImpalaSS08 4 года назад

      Will do. Thanks again.

  • @MrAddidas2
    @MrAddidas2 4 года назад

    Im not very mechanically inclined so I was wondering if a rookie could do this? I have codes po420.po430 and po441. Bought the car for 1400 knew I would have 2 do some work on it. So I'm thinking that I should try doing his myself instead of taking it 2 a mechanic and having him charge me an arm and a leg.

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Well, that's a tough question to answer, but what I would say is that if you are willing to give it a go, I think you can do it. The only challenging part of this was switching out the heat shields, but that is not required. Just make sure you have a foot-pounds torque wrench so you can properly torque the exhaust manifold bolts. Also, just be sure that you really support the car well before you climb underneath. If you don't have jack stands, maybe get some of those ramp things that you drive onto. On the other hand, if you choose a local mechanic, having them swap the manifolds would not cost too much, if you source the manifold yourself. Whichever route you choose, I wish you the best.

  • @melanin4267
    @melanin4267 4 года назад

    You are so good.. I'm frustrated with my 2004 Lexus GS. Everything we try we can't get the. Check engine light off. It keep failing emissions we replaced what the code said was wrong still the light keeps coming on. We payed 1500+ dollars already trying to fix this car. Ugggg🤦🏾 this is my third Lexus I love them but I'm so frustrated.. All the mechanics we take her to said there is nothing else wrong. They refuse to charge us.. Anyone have a clue as to what might be going on?

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Perhaps you could share the trouble codes you are getting. Also, be sure to check the intake resonator, it is easily overlooked by mechanics. It is the part of the intake tube that sits between the Mass Airflow Sensor and the Throttle body. It's black plastic, boxy, has a slight S curve, and has a metal heat shield on the bottom as it sits directly over the exhaust manifold. These resonators a notorious for cracking, and letting in air after the MAF, which throws off the whole system. The resonator is very easy to remove, but be sure to actually remove it, because the cracks, even when they are large, are hard to see. This problems can cause misfires, damage to your cats, and emissions trouble codes, so it would be good to give it a check.

  • @mdhoan
    @mdhoan 4 года назад

    Nicely done. I was able to follow and change out my Cat with your video.

    • @jcs_diy26
      @jcs_diy26 4 года назад

      That's fantastic. Thanks for sharing.

  • @burmesebeef
    @burmesebeef 4 года назад

    this is one of the best diy step by step tutorials i've seen on RUclips. Thank you good sir!

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Thank you for the kind words!

    • @zefdin101
      @zefdin101 3 года назад

      This guy has it down cold, no BS, every bit is helpful.

    • @Iceyboy300
      @Iceyboy300 3 года назад

      Yes sir good job. This will help me out a lot.

  • @davidnguyen5028
    @davidnguyen5028 4 года назад

    I’ve got a p430 code on my 2011 GS. Is that the front or the back manofold?

    • @jcs_diy26
      @jcs_diy26 4 года назад

      The P0430 code usually means that the O2 sensor downstream from the catalytic converter is not reading within specs. It's one or both of the front cats that is throwing this code.

  • @ronciucci1732
    @ronciucci1732 4 года назад

    Did this repair make the codes go away? Did the codes ever come back after repair?

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Hi Ron. You will notice at the end of the video that I completed all the drive cycle tests which resulted in no trouble codes. The video also shows that the vehicle successful completed the state inspection. The problem has not yet resurfaced. So, this repair did work for me.

  • @nikocruz3638
    @nikocruz3638 4 года назад

    Hey bud! Great video! By any chance did you have to do anything specifically to get the new one to fit? I’ve gotten the old one out but seem to be having issues putting the new one in. (Own replacement)

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Hi Niko, I missed this comment but still wanted to reply. I'm sure you have this sorted out already. I did not have any fitment problems with respect to the manifold lining up with the head and the exhaust pipe. I transferred the heat shields over, which wasn't easy because the new manifold wasn't designed for those heat shields, but the adjustments were to the heat shields and not to the new manifold.

  • @DavidDiaz-lm9bl
    @DavidDiaz-lm9bl 4 года назад

    Thank you so much master 👍

  • @vkhiev
    @vkhiev 4 года назад

    Very detailed thanks but I got a $5 fix for this issue. Just install O2 sensor spacer/defouler. Works 99% of time to pass emissions

    • @MadCowsProductions1
      @MadCowsProductions1 4 года назад

      yeah but these cars need cats replaced after a lot of miles, even with no code they start smelling like rotten eggs and can restrict the engine

    • @IS3000vato
      @IS3000vato 2 года назад

      my spacer didn't do shit lol

    • @jose-manuelespinoza7134
      @jose-manuelespinoza7134 Год назад

      I neglected mine and now I may need the cat replaced good thing u got urs fixed in time

  • @kelenmoore5977
    @kelenmoore5977 4 года назад

    Mine was only $800.

  • @rl6746
    @rl6746 4 года назад

    What penetrating solution do you use?

    • @jcs_diy26
      @jcs_diy26 4 года назад

      Hi there. I use the PB Catalyst penetrating fluid. Seems to work pretty well for me.

  • @TonyAlvar3z
    @TonyAlvar3z 5 лет назад

    Where did you buy your cat? I need one for my 2002 Lexus IS300. I don’t have smog check due yet but I would like to start now and not be rushed.

    • @jcs_diy26
      @jcs_diy26 4 года назад

      At just about 47 seconds into the video there is a copy of the order receipt. I purchased this from Eastern.

    • @TonyAlvar3z
      @TonyAlvar3z 4 года назад

      JC's_DIY yeah these are not legal in California, thanks anyway!

    • @jcs_diy26
      @jcs_diy26 4 года назад

      @@TonyAlvar3z These might work: "MagnaFlow Direct Fit CARB Catalytic Converter 452843" They are twice the price as the 49-state versions, but they still better than dealer cost. Good luck with your search.

  • @pinklloyd
    @pinklloyd 5 лет назад

    I'm wondering if the process for changing out the 06 GS 300 AWD exhaust manifold is the same. Does anyone know?

    • @spardu1
      @spardu1 4 года назад

      I am wondering this too, did you ever find out?

    • @2jz4life35
      @2jz4life35 4 года назад

      @@spardu1 should be the same. the 2jz-ge manifold in all equipped cars GS or IS are routed the same way.

  • @dennisbdavid
    @dennisbdavid 5 лет назад

    One of the best DIY videos I have ever seen! Great job!

  • @samd410
    @samd410 5 лет назад

    According to eastern and walker, you do not need the heatshields because the replacement converter is smaller in diameter than the factory once...…….great video.....thanks

    • @JohnPColbert
      @JohnPColbert 5 лет назад

      Thanks for pointing that out Sam. That's a great point as making the heat shield fit is the hardest part of the job. I like having them on there just to keep the heat off the starter and some of the nearby wires, but it's nice to know that the pipes can be installed without the shields: the job is much easier that way.

    • @IS3000vato
      @IS3000vato 2 года назад

      Hey Sam, can you post a link to this statement? I hope this is true so I can leave the heat shields alone if I can't manage to transfer them

    • @samd410
      @samd410 2 года назад

      @@IS3000vato According to eastern and walker, you do not need the heatshields because the replacement converter is smaller in diameter than the factory once...…….great video.....thanks

    • @samd410
      @samd410 2 года назад

      @@JohnPColbert According to eastern and walker, you do not need the heatshields because the replacement converter is smaller in diameter than the factory once...…….great video.....thanks

  • @EvilJohnny81
    @EvilJohnny81 5 лет назад

    I'm having no power issues when I drive my 03 Lex IS300 but I am getting the P0430 code. But I'm also getting the VSC and Trac Off light as well.

    • @HooyahPeacock
      @HooyahPeacock 4 года назад

      Trac light is a combo of things. I have the same thing now. Most likely its the O2 sensors bank 1 and 2 upstream. Go that route first if doesn't fix replace your vvti solenoid

    • @marcosman3393
      @marcosman3393 Год назад

      I'm getting the same issue: have you found how fix I tryed everything can't afford to take too shop.

  • @MB-rv9dx
    @MB-rv9dx 5 лет назад

    Are the manifold gaskets at the header metal multi layer gaskets? I ordered some and they are like 4 thin pieces of metal punched together

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      That sounds about right. The exhaust gaskets often have layers and sometimes metal rings around the exhaust ports. I don't recall exactly what the manifold gaskets looked like when I did the install, but at 10:36 on the video you can see the top of one of the gaskets. That might help.

  • @MB-rv9dx
    @MB-rv9dx 5 лет назад

    Did you have to remove the 2 rear studs near the firewall to remove the manifold or was there enough room/clearance?

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      I was able to remove the manifold without removing the studs. As I recall, the manifold came out easily with just a bit a moving it around for clearance.

  • @MB-rv9dx
    @MB-rv9dx 5 лет назад

    So if have p0430 and po420 just need to replace the exhaust manifold? Not the other rear cat? I’ve replaced o2 sensors, run lacquer thinner etc and I still have these f’in 🐱 codes. How much would a mechanic charge if I supplied the part?

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      I doubt changing the sensors fixed the problem for these codes, but the lacquer thinner may have helped. The codes will take a while to clear on their own, so you won't know if those efforts worked unless you clear the codes and go through the drive cycles. I cleared my codes manually and then drove the car through all the drive cycles to confirm the codes remained clear. If you supply the part, a mechanic could probably do it for around $500. It's important that they put the heat shields back on the new manifold, which may require a bit of fabrication: just a small amount of trimming. That's why I say $500. The manifold itself is a pretty easy job; however, it takes longer to get the heat shields transferred.

    • @MB-rv9dx
      @MB-rv9dx 5 лет назад

      Will this header work in California?

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      According to the receipt. No. The invoice says No CA or NY. I hope there is another aftermarket header available that you can find for a reasonable price.

  • @MB-rv9dx
    @MB-rv9dx 5 лет назад

    Are those gas shocks that hold the hood open stock?

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      Yes. Came with it... Still work too.

  • @aaronham5881
    @aaronham5881 5 лет назад

    great vid. i loosened the exhaust bolts but my exhaust studs started coming out also is this something that i should replace.

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      Sorry for the late reply. I'm sure you figured this out already. When they come out, that's not so bad, it's when they break that your day gets ruined.

    • @Joseph-jo6rm
      @Joseph-jo6rm 4 года назад

      @@jcs_diy26 I need to replace my Exhaust manifolds and flex pipe on my '93 GS 300. Since my ride has 2 manifolds and 1 flex pipe (Before the Cat), should I connect both the flex pipe and 2 manifolds before installing them or install them 1 by 1 separately?

    • @JohnPColbert
      @JohnPColbert 4 года назад

      @@Joseph-jo6rm It is a bit hard to say exactly as I cannot visualize precisely how the flex coupling attaches to the manifold, how flexible it is, and whether it could be installed after the manifolds are mounted. I believe the most important thing on that install would be to ensure the manifolds mate properly to the heads. If you can connect the flex coupling before hand and still maneuver the manifolds easily, then you can probably connect it before hand. If you do, I would recommend connecting it loosely and then tightening it after torquing the manifold bolts.

    • @Joseph-jo6rm
      @Joseph-jo6rm 4 года назад

      @@JohnPColbert Great! Thanks John, I'll consider doing so.

  • @bsouza1675
    @bsouza1675 5 лет назад

    I’m in Ca and the Lexus cats are $4,470.33.......crazy

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      No doubt. Great way to get you to trade in your car rather that fix it. Glad there are aftermarket cats available.

  • @sosabilly535
    @sosabilly535 5 лет назад

    Common problem with these cars but they run forever 💯💯

    • @MRMAN-wb1tv
      @MRMAN-wb1tv 2 года назад

      Going through this exact same thing, hence why I'm here.

  • @ricardoburton8672
    @ricardoburton8672 5 лет назад

    What brand catalytic converter did you buy

    • @jcs_diy26
      @jcs_diy26 5 лет назад

      It's an Eastern brand. At about 44 seconds into the video, I show a copy of the invoice, which includes the part number.

  • @Supraking12
    @Supraking12 6 лет назад

    Hi, is it required to replace the manifold gaskets when the manifold is replaced, can’t the old gaskets be used?

    • @jcs_diy26
      @jcs_diy26 6 лет назад

      I would recommend always changing the manifold gaskets when you change the exhaust manifold. I imagine you could try the old ones, but you obviously risk having it leak. The old ones would probably work, but the gaskets are not excessively expensive; so, it's really best to just replace them.

  • @Bluespower1792
    @Bluespower1792 6 лет назад

    Enjoyed your video, very thorough. One of the comments mentioned using a muffler shop to cut out the old converter and weld in a new one. Will that work? I'm looking for the cheapest option given the age of my car and an upcoming emissions test. Thanks for any guidance you can provide.

    • @jcs_diy26
      @jcs_diy26 6 лет назад

      Yes. That will work. Not sure if you can get that done for less cost then replacing them as shown here, but you can see what I paid; so, use that info and see if you can get new cats welded in for less.

  • @jajupa78
    @jajupa78 6 лет назад

    I cut the old ones out and fab in universal magna flow HM cats. Takes a lil bit but works every time. Love it when these come through my doors. Nice clip.

    • @jcs_diy26
      @jcs_diy26 6 лет назад

      That's a great solution. Having the cats welded into the manifold makes replacing them a difficult job. Although, the cost savings of fabbing in a couple of universal cats makes the extra effort worthwhile.

  • @ashleymonseen6731
    @ashleymonseen6731 6 лет назад

    I have an SC 430 in great shape, but I've noticed that when I really hit the gas, it just doesn't seem to be as fast as it did, I hear a faint almost rattle-like noise, and it puts off a sulfur/rotten egg smell. Is this what the problem is? If so will fixing it give me my power back?

    • @jcs_diy26
      @jcs_diy26 6 лет назад

      Rotten eggs is a smell associated with Failing cats, so is a reduction in power. It would be a good idea to have a tech check the in and out temps of the cats to see how they are functioning.

  • @ShawnT_1JZ
    @ShawnT_1JZ 6 лет назад

    thanks for such a instructional video, just purchased my first vehicle witch happens to be a 02 gs300 and it had the 430 code with conditional pass so il have to do the same thing here, for sure much much cheaper in the end,