- Видео 84
- Просмотров 230 768
Andrew Dahlen
Добавлен 30 дек 2012
Arduino - IR Beam and Servo Motor
Use and IR Thru Beam Sensor to control a servo motor position. Example Code
Просмотров: 149
Видео
Quickrun 1080 controlled by an Arduino
Просмотров 872 месяца назад
Quickrun 1080 used for RC trucks. This video shows how to control it with and Arduino and the PWM Shield by Adafruit. You could run 16 motors from this PWM Shield!
Promo North Dakota VEX Robotics Signature Event 2024
Просмотров 3322 месяца назад
North Dakota Signature Event Promo Video
"Spark Show" Rolloag WNSTR
Просмотров 692 месяца назад
Rollag Minnesota. Western Minnesota Steam Threshers Reunion. Traction Engine throwing sparks in the air for a large crowd
CREO to DXF to Carbide Create Toolpaths
Просмотров 1637 месяцев назад
Demonstration of exporting a dxf file type from CREO. Also how to generate the toolpaths / G code using Carbide Create Software for the Shapeoko CNC Router.
Threading on the Southbend Lathe
Просмотров 12 тыс.10 месяцев назад
Cutting Threads on a Southbend Manual Lathe
Turning to a finsihed size - Southbend Lathe
Просмотров 3,4 тыс.10 месяцев назад
Turning a feature to a specific diameter on a Southbend manual lathe.
Tapping holes on metal lathe
Просмотров 1,1 тыс.10 месяцев назад
Method for tapping holes on the metal lathe for better axial alignment between the tap and the workpiece
Southbend Facing and Turning
Просмотров 2,5 тыс.10 месяцев назад
Demonstration of facing and turning operations on the southbend metal lathe. How to selecte speeds and engage the autofeed for the carriage and cross slide.
Drilling Holes Southbend Lathe
Просмотров 1,1 тыс.10 месяцев назад
Demonstration on drilling holes on the Southbend Metal Lathe. For best results (most concentric) use a center drill followed by drill bit.
Southbend Lathe Select and Change RPM
Просмотров 2,1 тыс.10 месяцев назад
How to change the RPM on the Southbend Lathe. The model A Lathe has eight speeds - 4 high speed and 4 low speed (backgear engaged)
Southbend Lathe Overview
Просмотров 2,1 тыс.10 месяцев назад
Overview of the Southbend Model A Metal Lathe.
CREO to DXF to Carbide Create to Toolpath
Просмотров 303Год назад
Create a DXF File in CREO Parametric. Open the DXF File in Carbide Create. Create toolpaths for each cutter type
Intro Carbide Create - Cutting a Circle
Просмотров 286Год назад
Intro Carbide Create - Cutting a Circle
Shapeoko PRO CNC Router Startup, homing, jogging
Просмотров 120Год назад
Shapeoko PRO CNC Router Startup, homing, jogging
Series and Parallel Combination Circuit Analysis
Просмотров 32Год назад
Series and Parallel Combination Circuit Analysis
Manual Mill setting a repeatable drill depth
Просмотров 518Год назад
Manual Mill setting a repeatable drill depth
Manual Mill Edge Finder & Digital Readout
Просмотров 671Год назад
Manual Mill Edge Finder & Digital Readout
Honestly, you could recreate that wheel for modern use and sell them at DIY shows as a solid side-hustle.
You can open robot option by pressing I/O button and then press F1 (type) there it shows lot of stuff eg: digital,robot etc......
Superb dear
Really good video with real robot explanation :)
FANUC = AUTOMAÇÃO = ROBÓTICS : FUTURO = CHEGOU : AUTOMAÇÃO: ROBÓTICS = FANUC : DE : BASE : P/ TUDO : EM : ROBÓTICS : GLOBAL = WORLD = FANUC ; 2030 ! ( A.I.) INTELIGENT = ARTIFICIAL = 2030 = PRONTA !!! ❤❤❤❤❤❤ .
FANUC = AUTOMAÇÃO = ROBÓTICS : FUTURO = CHEGOU = PARA = FICAR = P/ SEMPRE !!!❤❤❤❤ = FANUC = ROBÓTICS = 2025 ❤❤❤❤ .
where can we buy this taping kit?
so pro
Very helpful, I know that I would need to drill holes in order to use the high strength axles just wasn't sure of the method. Will be going hunting for the kit and drill bit. The current 8'' shafts are a constant nightmare with the inserts that dislodge continuously
Thanks for your tips
I didn't expect to see Kaden in the video
In your video on how to use the competition template, i have a question because comments are turned off. Im using a drivetrain, and the .spin command does not work, and i have to get this done for states tomorrow. Please get back to me!
camtasia
Did you ever make this available to people? We're looking into using more 1/4" shafts now
Flaming fury was good, but its intake needed a little work
There's no shooting system
These were not that great they wouldn’t really compete in a real competition
Me or did none of the robots comply with specs
Rockyx is the only one that wouldnt completely fail
Drilling and tapping holes takes forever, and has to be done just right
Nice video sir
what about expansion zones
5:06 - 5:56
That hit the flag only half way
Pussy
lmao what is going on?
Not very efficient either
Most of the robots didn’t seem like they were consistent when it came to picking up stuff
yes, I agree, and why do people make their punchers so long? it only needs to be a few inches
Te voy a copiar perro
Why is that one kid in the background every time? and why is he so pissed off?
The flaming fury launcher bot has a really cool ball intake design, I dig it
It's interesting, although it would be cool if it could actually pick up caps lmao
I guess it was interesting but like you have to push the ball up against the wall and it’s seems like it got stuck when it was rolling down that shaft part of the intake that leads to the fly wheels