- Видео 122
- Просмотров 304 793
How To Guru
США
Добавлен 30 апр 2020
This channel covers OUTSIDE THE BOX THINKING for shop related modifications to speed processes and gain insight to modify, tweak, adjust and/or fabricate tools and fixtures for YOUR PERSONAL SHOPS NEEDS! Professionally I've been a prototype engineer since 1980 and I'm always looking for a better way to do absolutely everything! I'll go over shop tools and show how you can benefit from hundreds of tips/accessories/fixtures that some may never even heard of! I'd bet anything you'll find TOTALLY NEW usable tips/tricks on this channel! These are MY PERSONAL tweaks/ideas for my shop. We'll THINK SMARTER together to be better faster more accurate AND Safer!
DIY POWER FILE!
DIY POWER FILE! Create parts that replicate factory made part. Add a nice radius, some blended curves or slots EFFORTLESSLY! Save a ton of time filing! I show its use doing a small radius but think of the possibilities here? A 1" stroke length is generous enough to create a lot of "other" options. You need a variable speed saw or proper rheostat to lower the speed of all reciprocating saws to almost a crawl as slow speed is used for any filing so gullets have time for chip removal.
Also BE SAFE! Any mass added with friction only set screws should never be used in a high speed fashion! It might/can/could/may/will(?) detach due to insane G forces.
Also BE SAFE! Any mass added with friction only set screws should never be used in a high speed fashion! It might/can/could/may/will(?) detach due to insane G forces.
Просмотров: 397
Видео
A BETTER WAY TO CLEAN TOOLS!
Просмотров 7373 месяца назад
A BETTER WAY TO CLEAN TOOLS! transformed a 30 year old jig saw to box new with just 2 paper towels! How do you clean tools? Perhaps Windex & paper tower or shop rag? If so, try this and prepare for a much better more effective cleaning of what's left behind. Incredibly impressive results left me jaw slacked! It literally looks perfectly 100% NEW on 1 side.
YOU CAN'T DROP THE NUT AGAIN!
Просмотров 5323 месяца назад
YOU CAN'T DROP THE NUT AGAIN! shows my way of never dropping the nut again! I devised this way after 1/2 an hour searching through a saw dust heap! After thousands of blade changes in almost 45 years this method is well proven!
VIX BITS! Mans 2nd Best Friend!
Просмотров 4934 месяца назад
VIX BITS! Mans 2nd Best Friend! shows a drill bit that centers itself, is retractable for bit protection, offers adjustable depth and needs no special replacement drills! Buyer beware of bits that are much cheaper! A set of 3 is around 25.00, IF you want your bits for a lifetime, AVOID look a like sets of 10 for $9.99! (amazon seriously)
How to BEND PLASTIC PROFESSIONALLY!
Просмотров 7674 месяца назад
How to BEND PLASTIC PROFESSIONALLY! shows a DIY 2' strip heater bending 1/32 Styrene in 30 sec.! I'm using 1/2" Marinite for the surface and underlayment with .020 Ni-Chrome wire at ONLY 16v AC! Add a 15 amp rheostat and it's bending time! This typically powers 2 or 4 foot strip heaters with ease. FYI 35v AC powers a 4' heater using a pair of .020 twisted Ni-Chrome wires. You must use an AC vol...
CUTTING THIN STRIPS on Table Saw!
Просмотров 1,3 тыс.4 месяца назад
CUTTING THIN STRIPS on Table Saw! is simple with a fixed spoil board and zero clearance insert! On this saw, strips are accurately cut down to .030 (1/32 .75mm). How about .003 variations in strip width if you follow a few tips! Don't forget safety glasses as thin strips can never be trusted!! Razor sharp blades only and YOU MUST USE A ZERO CLEARANCE TABLE INSERT!
THE WIRE MESS IS SOLVED!
Просмотров 8534 месяца назад
Tired of wire bird nesting and wasted time? THE WIRE MESS IS SOLVED! With a zip-tie & O-ring you'll never waste time again with auto spooling or tangled wire! Even hitting the floor it stays tightly rolled. Wire is always ready to use no unraveling, re-coiling or finding the little hole(s) for storage. With less wasted time now you'll have time for a vacation or 2! ;)
Make nail/staple blowouts a thing of the past!
Просмотров 1,2 тыс.4 месяца назад
Holding your air tool parallel or perpendicular can easily Make nail/staple blowouts a thing of the past! Have you ever noticed the chisel direction on a blown out nail? They are always parallel to the surface they blew out from! This is a strong indicator you could have avoided with this video. Twist the tool a better chance to NOT blow out close to an edge.
ACCURATE PRECISION DOWELING FREE!
Просмотров 7324 месяца назад
ACCURATE PRECISION DOWELING FREE! shows 8 perfectly aligned drill holes being drilled in real time forming an amazingly accurate miter. Without a drill press, create mind bending tight fitting joints. With these tips you'll never have a poorly placed or drifted hole ever again and EACH will be at 90°! And, without any need for a drill press or expensive fixtures!
Virtually STOP HOLE SAW CHATTER!
Просмотров 1 тыс.4 месяца назад
I show the reason this happens and 2 ways to solve the issue! Rock Maple is drilled without any center drill avoiding chatter with simple tips to Virtually STOP HOLE SAW CHATTER! I include 2 other ways to cause smooth results with or without an air compressor too! Hole saw kits are hundreds of dollars and this is how to get decades of service from your set. STOP HOLE SAW CHATTER shows how to ke...
-10° BELOW ZERO AIR CHILLER!
Просмотров 1,2 тыс.4 месяца назад
-10° BELOW ZERO AIR CHILLER! Remove heat faster, Drill, Mill, Cut, and Grind faster without melting, warping or distorting items. Protect bits when deep drilling in any material! Protect Forstner and drill bits from heat damage. Protect hole saw drilling from burn marks! Drill multiple holes in metal without heat transfer. Weld thin metal and protect a surrounding area! Break rusted parts free ...
MAXIMIZE HEAT In Low Powered Soldering Irons!
Просмотров 8784 месяца назад
MAXIMIZE HEAT In Low Powered Soldering Irons! Improve low power soldering joints FAST! Conductivity is your enemy soldering with low power. We need to minimize 2 heat losses. What's holding the wire insulation area and the termination point itself (any metallic connection you need to hold). This simple little fixture can help joints to flow better because you can get all your heat to the joint!...
FREE BENCH VISE in seconds!
Просмотров 1,4 тыс.4 месяца назад
FREE BENCH VISE in seconds! From scrap to clamping parts in under 2 min! Simple scraps turn into handy clamping surfaces instantly. Plywood, solid wood, composites all work to make a bench vice in literally seconds! Screw from the front or underside to make an immediate surface to hold parts for many different applications. From gluing to sanding, polishing, soldering, mini routing, all are eas...
Riving Pins ADD SAFETY!
Просмотров 8834 месяца назад
Riving Pins ADD SAFETY! ADD SAFETY BACK to a missing or removed anti kickback assemblies. I show how pins keep kick back at bay too! Exact location of pins in saw kerf alignment is PARAMOUNT. Simply inserting pins as needed is much safer than nothing! Pinch is mitigated right after the saw blade in vertical cuts ONLY though. This is why I wish mine came with an actual riving knife. My old anti ...
FINALLY SIMPLE VACUUM FORMING AT HOME!
Просмотров 3,2 тыс.4 месяца назад
FINALLY SIMPLE VACUUM FORMING AT HOME! I form small parts in real time from thin styrene. All you need is a shop-vac, heat gun(s) or oven and a tool (the part you want to replicate in plastic sheet). I made all of it from scratch plus drilled the tools and had 1 sample of .060, .040, and .030 to trim out in just over a few hrs. If you have an oven, it's able to conquer larger parts and consider...
IMPROVE DRILL PRESS ACCURACY IMMEDIATELY!
Просмотров 2,5 тыс.4 месяца назад
IMPROVE DRILL PRESS ACCURACY IMMEDIATELY!
STOP CHOP SAW BURNING FOREVER! (stop part sliding)
Просмотров 9244 месяца назад
STOP CHOP SAW BURNING FOREVER! (stop part sliding)
Grizzly G1071 Service 30 years later!
Просмотров 1915 месяцев назад
Grizzly G1071 Service 30 years later!
I have an X5 unifence that I love. The original rail was getting chewed to pieces by the locking handle(on the inside). This video helped me get it all back together and running like a champ. Many thanks for taking the time to make these videos. It was super helpful.
Thanks for the reply! Glad it helped!!
I've also used copper solid strand wire and made a ring to fill the gap. And it doesn't allow the dill to lock up on the arbor. Loved the ideas.
One guy replied just add an O-ring...OMG does it work well to take up slop! Hey, Thanks for the visit/comment!
Very generous of you to share! I downloaded your video, just in case my unifence needs major adjustments. Thank you!
Thanks Jim for the visit! Any questions feel free...
Very generous of you to share! I downloaded your video, just in case my unifence needs major adjustments. Thank you!
Ideas, maybe. Accuracy as titled,NO!
Bob I'm sorry your incredibly wrong here. It helps immeasurably to drill parts.
Is there anything hive tools can't do?
How true! Thanks for the visit!
this is my first unisaw/unifence I used my Father’s Jet lock/ tubular fence on his old TS. I had no idea how this even worked. This was the perfect video! Going to finish the refurb tomorrow and hopefully have my first solid locking fence. The jet lock never was solid. Oh it is possible to mount the locking lug(?) facing the wrong way ?
If it goes together it should be right due to the offset roll pin hole. Just check the fit last to assure yourself it locks properly before you powerup the blade. Thanks for the visit!!
Picked up an older Unisaw and the fence would not properly disengage from the rails; it had to be slid out at the end. After watching your video I figured out I needed to replace the ball bearing and spring. It works perfectly now. Thanks for the help.
Glad to help! Thanks for the visit!
Holy crap Joe!! You are super talented!!
Kudos! You have a cool channel, I have some exploring to do!
Can you explain in more detail about "rolling" the ramp angles? Are you sanding, grinding, filing, burnishing to get that rolled edge?
At 2:13 you can see a reflection indication of the roll size and its more than enough to force engagement. Use a fine file and keep the edges flat while rounding them. You don't want any file marks or sanding marks leftover when your done. If the edges are nice and flat and smooth, engagement will also be smooth. FYI, rough edges are not good for the inside of your fence rail extrusion so sand smooth and you'll be rewarded with how nice it works now.
Brill TY!
Glad you liked it, Thanks!
Hope you are doing well, Joe. Also hope you aren't feeling burnt out from putting out so many videos so quickly. It was awesome getting so much information so quickly, but it's hard to maintain that output. Most of the channels that I subscribe to put out a video a week. Easy to create that level, without burning out. Thank you for the knowledge shared so far, anticipating more quality content from you.
Wow Raymond, nail on the head! Back was bad for about a week and the numbers fell like a rocket sled to hell! Apparently I can't vacation or do anything else? This is not for me when screw tube decides to drive everything into the ground before my back issue happened. I had 250,000 views going on in a week then the plummet into the toilet as I disappeared from the main feed. And burnt out can't explain it, it's worse as your every waking moment revolves around screw tube and I've had enough of that. I hit the videos hard to make a channel quickly and give all of you a good sampling of what to expect...8,230hrs of watch time for 200.00 is a punch in the face and a kick in the boys IMO. Not sure if I'll come back to this...Thanks!!!
@@joesshop3622 Sorry to hear about your back, hope it's just muscle aches and nothing more serious. It's sad that your efforts haven't resulted in decent revenue for you. I understand why most of the worst content creators have turned to prostituting their feeds as product advertisements. Thank you for not doing so. I greatly appreciate your style, quick videos without five minutes of promotion and begging to like, subscribe, and mash the notification bell and video highlights. Simple and to the point. I fast forward through most of the feeds that do those things and I know I'm not alone. There are other ways we can support you. Join options and patreon come to mind. I have unsubscribed from many channels that started out great like yours and transitioned to only doing videos to fulfill their product sponsors instead of their audience. Maybe analyze the intent of doing videos. If to teach and share knowledge, please keep doing so, and rely on us for financial support (like AvE). We appreciate the effort and the knowledge. If primary for income, well... Motivation drives output which generally leads to fulfilling product sponsors and advertisers before the interests of viewers. If you can do so without losing trust and respect of viewers by calling out crap sponsored products. Too many are afraid of losing sponsors and betray the audience. One video a week is a good metric, based on the output of the successful creators that I subscribe to. Maybe five minutes of content, I'm guessing an hour or two of production. Thank you for sharing your knowledge. It really is appreciated. I hope you continue and find success.
@@raymondmiller4981 Thanks much Raymond. Much appreciated commentary! I'd never ever ask for $ yet I'm so broke I can't afford to pay attention, literally. Motorcycle pickup T-bone sent me flying 65' in 1991. Back nowadays is unreliable so I thought I'd try "YouScrewed" It's sad creators are put through their sieve of nonsense and lies.
Best wishes to you Joe. I have been yearning to see more of you but had no idea about your pain. I’m right there with you in the same battle. I have enjoyed every one of your videos. You have a tremendous amount of talent, knowledge and a great friendly personality to go with. Take care of yourself and I hope you can keep your channel alive in some way.
Thanks for the compliments but its more ScrewTube taking me off the main feed. Watch hours are a joke now. I don't get what changed?
Great video! I'll definitely be doing that tune up ,I just bought a Platinum Edition Unisaw what's the difference between that and the regular edition? Thanks for any info
I don't recall the difference Mike, sorry! Thanks!
Just got done doing 4 clamps I thought were ready for the trash. Thank you. Took maybe 20 minutes and they now are usable again .
@@joesshop3622It has been awhile, but it just came up one day. I have been planning on doing them, but kept putting it off. I needed to have them working good for the project I am working on so decided it was time. Again, thank you for the tip.
@@jsstacy7861 Thanks!
What are the parts you used for the hub/arbor?
I mention it in the video as 3/4 x 2. Thanks!
Now that’s a “makes my life easier “ device that I can do with Thank you
FYI, the heat generated doing this at the wrong feed and/or speed can cause work hardening! Usually lower than normal speed with slightly faster feed rate is better. Thanks!
I just use a grinder motor.
Please explain your setup further...that's what this is all about, ideas! Thanks!
@@joesshop3622 Good ol’ fashioned grinding wheel on a motor. They usually have a wire brush on the other side.
One must not forget stones smear or wear away material while making lots of heat and uneven surfaces but they can't cut anything in reality. They also leave a finish that's poor. I prefer a smooth even radially true 90°edge that's ready for paint so I thought I'd share...
Different tools have different purposes, of course. I respect yours, but when I need to takeoff material fast, I use the grinder wheel. As for surfaces and “pretty,” You get a fabulously beautiful finish with a “surface grinder” I have several in storage right now that I am about to sell.
@@joesshop3622 Different tools have different purposes, of course. I respect yours, but when I need to take off material fast, l use the grinder wheel. As for surfaces and "pretty," You get a fabulously beautiful finish with a "surface grinder" I have several in storage right now that I am about to sell.
A good idea. What kind of blade did that jigsaw have? The screw in blade saws might be easier to convert than the “T” blades.
Exactly, the T approach won't work. Almost every older saw is of the "screw type" design. A perfect use for a tool that has no quick change and has that dreaded plug in leash.
How does Ballistol work compared to WD-40? I have used WD-40 to clean the outside of a Kennedy Tool Box with the crinkle brown paint.
I have not done a comparison I need to try that, great idea! Especially since you can get WD-40 anywhere but McDonalds. Thanks again Brian!
Fun. Filing perfectly straight on something that can take awhile is difficult. It’s a losing battle without help.
Yeah not much fun to do, which is why this will help immensely. Used it again today and I'm liking this!
Back 50 years ago I used to be the official flashlight and tool holder for my dad. I remember every time he finished working on a car he would get out the 1 gallon gas can and clean all his tools from wrenches to ratchets. In the winter he would bring them inside to clean them and my mom would get made about the odor. Cleaning tools in the living room was okay just not with gas. I have never heard of blastitol .
Wow a blast from the past! I remember cleaning mini bike parts and roller chains in a coffee can with gas. A tad dangerous with standing pilots back in the day...
Hand Cleaner Works Just As Good For Me
What type/kind of hand cleaner? That's a killer Idea, always looking for a better way to do everything! Thanks Roger!!
That's a good tip. Always proud of how clean my tools are so this is helpful to keep them looking like new.
Years ago I worked in and ran the model shop at a company that folded after 6 years. All my company tools were sold at auction. ALL the model shop tools went for a premium because all of them looked bran new. Full size mill, 20" planner, spindle sander, routers all did really well for the bank. I bought my custom ordered PVI vac former for 1/4 price with 40 hrs. on it. lol. It then paid for itself in less than 2 weeks.
Baliatol is a favorite. It is my rag in a can oil.
I've had the can for 15 years and never barely used it. Now it'll finally get used...
Ballistol is primarily a mineral oil that easily emulsifies in water. It might be worth trying a mix of mineral oil, water, and a drop or two of dish detergent in comparison.
The can is decades old and finally it's way more useful. Next I'll have to give your version a shot to see... Thanks Again!
Wow! That’s a killer finding Joe. I have a few stainless steel squares and steel 123 blocks that I have to maintain with some light gun oil and Scotch pads to keep them from rusting. To use Ballistol on the plastic isn’t something that I have gave thought to.
Try this on your blocks. Clean them good then heat them super warm (hair dryer high temp till you can't hold them) and spray them right away with silicone. Wipe with a dry paper towel AFTER cooling. Heat opens just enough porosity to let in the silicone and... you know the rest.
Great tips. Thanks. I will have to watch again.
Please do, then let it run in a loop while you sleep! Subliminal table saw training 101 LOL Thanks Randy!
I always raise the blade as high as it will go! Additionally, the tightening of the nut is always opposite/counter to the rotation of the blade...helps keep the nut tight even if there is slight initial slippage!!!
I mention this slippage tightening issue @ 2:04. Thanks Much Fookingsog!!
Vix bits are awesome tools for the workshop. I’ve had mine for almost 30 years now and they still work great. I wouldn’t want to install a piano hinge without one. 😂
It seems every time somebody new stops by they ask what they are or what they're for...So this video was born lol. Mine are also older from the early 80's and only one of six bits needed a new drill...due to um...an endo. THANKS again!
As others have stated this is brilliant! New life for my old weller gun and the scrap romex I told my wife I needed to keep as it would come in handy some day.
It works so well I'm amazed nobody has a video on this. 3x faster (at least) to solder thicker wires! Thanks BA!
I know this sounds like a strange question but the screws that hold the capacitor to the motor, what should one be looking for when those need to be replaced? I acquired a bandsaw with an old Delta motor without the screws holding down the capacitor. So I really don't have something I can compare to. I understand the screw shaft diameter is important, but isn't the length important too?
I tried to find my old motor from 1965 that came with mine but to no avail. Sorry I can't help! Thanks for the visit Byron!
Very mad scientist. Love it.
I use to have one you could literally pull half a car inside of it in the garage for 30 years. 200AMPS just to turn it on! Ordered it from PVI with a massive 250 gallon tank. Freakin' riot, virtually automated, except the guy pushing buttons. It would get so hot in the summer 140°+ I built a tiny cardboard hut by the control panel that had its own air conditioning. That was MAD LOL!
@@joesshop3622 I need to bring my gas remote buggy into store for the older fella there to look at. Might be lost cause after sitting so long. Remaking the plastic shell would be fun.
You have not fitted your blade guard. Essential safety for a table saw. Sixty thousand of your countrymen injure themselves on table saws every year. Most would be saved if they did not remove safety equipment. Not using a guard is bad. Showing others that you do not is worse.
Please see my video Deluxe Table Saw Sir...I've got it covered. I'm a freak show about my safety for more than 45 years on table saws up to 8hp and 16". Many configurations of "safety" cause the accidents, mostly during small part operations I do the most of.
@@joesshop3622 Not in this video- I can see it, not covered. And your advice for 'if you don't have a riving knife' should be 'fit one before using the saw'.
@@Tensquaremetreworkshop One might assume the vacuum snout with 10 rubber capped hold down wheels flanking the blade and 3 riving pins would be satisfactory supplements? Those wheels really mitigate a lot of other issues too. Thanks much for the concern Sir, safety is paramount, with this tool especially!
Thanks for the tips. My unifence has been working great since I bought the unisaw 52inch new in 2000. Saving the video for reference when I do need it.
Thanks You!
If you don't have a riving knife, you can set your fence to the edge of the wooden insert, and run a kerf (you need another insert) back to the kerf in your insert, and glue a piece of material in it. If you have a thinner blade than your regular, you can center a smaller slot that the blade. This used to be a common method for making a riving knife when saws didn't have them. The one problem is you need to be sure that your home made insert won't lift out of the saw. So whatever system your saw uses to hold the insert in place, you need to be sure it isn't just gravity, and you are sure all is good, even if you add this feature to it.
Thanks!
Whoa - BINGO. I love this. Made my day.
LOL Thanks TOM!
mind blown 🤯, i am definitely using this, and you just got a sub sir.
Awesome, Thank You!
Great tip😊
Thank You BDBrad71!
I have analyzed your RUclips channel and found out some problems. Your video title and video quality very good but you have some problems for did not get more views. if you want I will fixed that problem. Do you want to talk about it for a while?
Your the 2nd mentioning this but he was a scammer...all I want is to help people with some FREE tips. If you feel the same, I'm listening...lol
thank you for the clear thumbnail and zero clickbait! the video actually adds information and does not waste time
Thanks Delo! Click bait won't be found HERE! My aim is to make it short as I can to bump the value per min. Who want's filler? I'm monetized but won't pull that. Everybody hates that so you'll see most videos are short and to the point... unless there's a lot to cover. Like Deluxe Table Saws 67 secrets.
I love this one!
Truly 'worth the price of admission lol"
This got me thinking: I keep all sorts of tape in a couple holders I made, but I’d love to know if you’ve got a guru method for that….
@@composerken send me a pic if you would...cmworks@charter.net
Like the Content? Please Like and Subscribe to help the channel.
Who doesn't enjoy detangling 50' of wire? It's therapy no?, just kidding!
LOL Thanks!
We determined this to be true years ago when installing casing around a window. The nail would deflect into the finished side of the jamb and make a mess. What was worse, when you have PVC windows and jambs and the brad would blow out a chunk of the PVC. So difficult to repair.
Sure you found out early lol, I could have used this information a whole lifetime ago. Thanks Barry!
Hilsch Tube. We used them to heat and cool chokes on carburetors back in the day. Snap On sold one.
I'll bet those were cheap! LOL🤣
@@joesshop3622 Blue Point YA862 Choke Tester.
To stop vapor lock?
@@The_Ascension For testing the manual choke on a carbureted vehicle.
I use HVAC aluminum foil duct tape! It is a wonderful shim material! I use it anywhere I want a permanent shim!
Great idea! I actually have some labeled .0035 for just as you say, thin shims!
Now I'm thinking of making an extra long, slightly tapered riving knife for my saw in addition to the little 2.5" wide one I commonly use. You are a font of continuing inspiration!
Thanks fxm, good luck on the project!
Yep. Bevel parallel to the grain structure can most definitely cause problems!!! Depending on the density of the growth rings and whether or not a knot is nearby can/will determine the movement of the brad/nail/staple. When I used to work at a roof truss manufacturer, I picked up some Southern Yellow Pine scrap cutoffs to make a workbench that were so insanely dense (and HEAVY) that I couldn't even power in deck screws with a cordless drill--the screw head would always twist off first!!! I ended up drilling all pilot holes and rubbing the screw on a bar of Ivory soap for a bit of lubrication to ease it in!!! This dense SYP is what they used for the long clearspan bottom chord of the roof trusses! I never tried air nails on this wood, but I'm not sure if I'd chance it!!! 😬
Reminds me of the HI-density MDF at almost 80lbs a sheet. The nailer would just fold up a nail into a pile of twisted wire from a big 3" nail. Never even getting a chance of any penetration.
Yup, that's the way I think about it. If you drive it in with the bevel along the grain, you are far more likely to split the wood or divert the tip along the path of least resistance (those nails do tend to be pretty soft). If you drive it cross grain, it may take more force to cut the fibers instead of split them, but it is far more likely to go in strait and you are far less likely to split the wood. Sometimes when I'm working with round nails or brads I will take a few minutes to prep the tips into a chisel point instead of a pyramid for exactly this reason. I learned this from restoring 18th century furniture built with wrought, chisel tip nails. They almost always drove them cross grain, especially when clinching. I suspect that driven cross grain is more secure as well.
Well said! Thanks again FXM!
Did I miss something? How does it work and where can you buy one?
On line $40.00 to many hundreds! Search Cold Air Guns. Better units go 100° below compressor air temp. This is important since they use a lot of air and will warm up your tank if you plan on using it for a while. Nothing to do but pay for it one time. No parts, no nothing to buy or add again. Just add 120 psi pressure.
I hope this makes sense. Hot air rises cold air sinks. Naturally. In this case. One is forcing air to escape quickly up as “exhaust” while the other down “condense”. This causes a separation in pressure. In other words. The heat from the motors that compresses the air also gives the opposite in return.. Cold air. The same principle in HVAC. You could as seen demonstrated and similarly use just a T-connection with the air going in and splitting a tube of air going up while another in a twist or two in a circle going down. The up exhaust opening has to be larger than the down or condensing side.
@@The_Ascension Fantastic explanation! I was sick the days they taught that in school! LOL!! Thanks!!