- Видео 30
- Просмотров 78 053
mikrobe1
Добавлен 7 окт 2007
Видео
naber oven with sestos pid regulator
Просмотров 1697 лет назад
oven for heat treatment. max ~1100°C / 1,2KW
SESTOS D1S PID regulation oven / Ofenregler Temperaturregler
Просмотров 2,9 тыс.7 лет назад
was originaly autotuned on 800°C level. Now heating from 20 to 200 °C. WIth initial overshoot. Switching done by SSR. Type K Thermocouple. CTRL:3, CTL: 1 Parameter from autotune are: M50: 714 P: 82 t: 15
pcb milling diy cnc
Просмотров 1,7 тыс.8 лет назад
Spindle 12000 UPM, Carbide D-Bit, milling depth 0.1mm, pre-mill height scanning.
Hard Turning a HSS Shaft on a lathe with a CBN Insert
Просмотров 11 тыс.8 лет назад
Abdrehen eines HSS (MK1) Schaftes mit CBN Wendeschneidplatte. 2100 min-1. ap=0.1mm hart drehen
Drawbar and Spindel Encoder SK30 Sieg SX3 CNC mill
Просмотров 1,4 тыс.9 лет назад
Bajonet style manual drawbar for SK30 BT30 Holder.
Piano Sonata No.2, Op.35 Frédéric Chopin CNC midi to g-code
Просмотров 8089 лет назад
Like other machines she is playing classic in her spare time.
linuxcnc: cnc engraving uneven surface autolevel with g-code ripper from scorch
Просмотров 4,5 тыс.9 лет назад
linuxcnc g-code ripper uneven surface sk30 holder sx3 sieg milling scorch cnc
ZD-915 Desoldering Station Power consumption
Просмотров 2,4 тыс.10 лет назад
ZD-915 Desoldering Station Power consumption
konische spirale cnc conical helix gcode
Просмотров 1,6 тыс.10 лет назад
konische spirale cnc conical helix gcode
pfaff sewing machine - pfaff nähmaschine 541
Просмотров 3,4 тыс.15 лет назад
pfaff sewing machine - pfaff nähmaschine 541
walking needle nadeltransport pfaff 541
Просмотров 2,4 тыс.15 лет назад
walking needle nadeltransport pfaff 541
Betonkugel Kugelbrunnen - Concrete Ball Spring
Просмотров 83817 лет назад
Betonkugel Kugelbrunnen - Concrete Ball Spring
Is flood coolant bad for this application?
Hello! did you make the BT30 spindle yourself?
What type of mill did you used ?
Tell me you don't know how to use a clamp meter, without telling me you don't know how to use a clamp meter. Wire is supposed to run parallel to the clamps at the shown With Arrows location. Second you need to remove the zeroing between measurements especially in DC, so it doesn't stack the zeroing. But yeah good show.
In the neighborhood
bonjour ,j'ai le même pid mais je n'arrive pas a le régler sur mon filastruder des que je mets le moteur d'extrusion en route la température chute très vite et beaucoup ,pouvez vous me donnez les procédures de réglages ,merci hello, I have the same pid but I can not adjust it on my filastruder as soon as I start the extrusion motor the temperature drops very quickly and a lot, can you give me the adjustment procedures, thank you
Mich würde interessieren, ob das Hartdrehen bei einem deutlich kleinerem Durchmesser (ca. 5 oder 10mm) und bei 2100 min-1 auch funktioniert.
Ausprobieren. Wird vermutlich funktinieren, da der Schnittdruck bei CBN sehr gering ist.
Whats the lowest value it can read?
Que programa (SOFWARE)usas para pasarlo a la máquina?
Good for a cheapie! I'm going to buy one soon, but I'll get the UT211E , because it does DC current in the clamp.
The shown measurement was in dc mode. The 211b has 4000 counts and a VFD mode
Geniale Sache. Machst du solche Kugeln auch auf Auftrag?
WOW. What about finish? How similar to grinding?
is this 1x speed?
Yes 1X.
nice machine
good enough
Sestos indicates whether the decimal digits of the probe K without using PT-100 as in the controllers REX C100 / 700, and the like?
Greeting It will be nice to measure in 600mA range.I'm curious to see how stable is
This multimeter does not measure DC at 600mA, only AC
Hi there! I'm curious about the UNI DMM. I noticed the UNI DMM does not have decimals, only straight round whole numbers. is there a manual setting vs auto ranging to select decimals?
Hello, I am interested in the process of installing g-code ripper to linuxcnc. Can you explain to me PROCEDURE. thank you
I have the same type, Pfaff 541. Any tips for the machine? :)
Do you have this sewing machine?