![dick smith](/img/default-banner.jpg)
- Видео 5
- Просмотров 72 009
dick smith
Добавлен 15 фев 2016
jockey wheel top bearing change.
Ifor Williams / Alko 48mm jockey wheel top bearing change. Parts bought from ebay # 295190613640
Просмотров: 215
Видео
Maxxfan, Mercedes Sprinter using my new designed gasket
Просмотров 3342 года назад
Maxxfan, Mercedes Sprinter using my new designed gasket
VW T4 Vacuum pump oil seal leak, seal replacement
Просмотров 10 тыс.3 года назад
Vacuum pump seal replacement on VW T4 2.5tdi 2002
leaking sunroof, clearing drain tubes Nissan Micra
Просмотров 6 тыс.4 года назад
leaking sunroof, clearing drain tubes Nissan Micra
Thanks so much, didn't know how to do this properly with a previous Micra, used silicone, problem reoccured after a bit and, yes, the sills did rust. Who knew all that gunk was behind the wheel arch! Have the same issue now with another one and love your clear instructions. Very satisfying to see the tube flushing clear. Off to confidently sort the problem thanks to you. Appreciate you taking the time to make the video.
Thank you Dick, I will give this a go, had tried clearing the top drains which seemed to expel water under the car, however I didn't know about the wheel arch issue! Just need to find a cable long enough to push through the rubber drain! Thank you so much!😊
Top lad Dick
Life saver! Thank you
Omg thank you for this. Was so helpful. I have exactly the same micra and the same problem. Been trying to seal it with silicon from the top. I feel so stupid now. I will do this tomorrow. Thank you again
Hello Dave, about to fit the same fan to a LDV Delivery 9 van - What material and how did you cut the material to form the gasket?
Hi Dick very interesting video. What did you use to make your gasket? Are you making the plans available?
Thanks for this video - swapped RL 3 on my Baxi 105 HE PCB and instantly powered back to life. Saved me a fortune
Thanks so much Dick. you video was super clear and seems to have done the trick. No more soggy bottoms!
Nice 👍 thank you.
Ok so how did you test that the pcb relay was defective, or was it based on other peoples suggestions that this was the fault?
is this the vacuum pump for the brakes?
Yes
@@MTinakari thx for the quick reply 🤣
Mines flashing 30 degrees. Any idea what that is?
Excellent video. Thanks for sharing
Bloody life saver, cheers! Hopefully this has sorted the issue, didn't even know it had a drain
Hi. Thanks for the tip. I have same fault. Changed relay but getting same fault. Any ideas? Guess it needs a new PCB?
Hi,thanks for this, it's great, and v clear, though I haven't managed to unblock the drain hole yet. When I pushed the cable in it hit something solid near the top, and couldn't go any further. I tried going in from the top and the same thing happened. any idea what this might be? I've got a 2002 Micra tempest if that makes any difference.
I also have a 2002 tempest and am going to try this tomorrow! :)
Thank you for this, I will give this a try today
Rather than just TALK about what you did, it would have been a million times more helpful if you had SHOWN us what you did - filmed yourself in the process every step of the way.
great explanation and video thanks
Perfect! Thanks mate - cars all sorted. Excellent job, appreciate it!!!!
Does the wheel arch muck actually share that cavity with the sunroof drain?
Thank you 😊
Thanks for this. I went out this morning to my daughters car and it was like a swimming pool in the passenger foot-well. I located the drains in the sunroof but had no ideas about the mud collecting behind the wheel so I now know exactly what I need to do to sort it out. Many thanks.
Thanks for taking the time to explain how the pipework can be accessed & cleaned 👍
Woow! I wonder if I can access this tube in an m35 Infiniti
what do you have to ask for when buying a relay and who do you ask? I try to avoid bothering my landlord as he raises rent and might kick us out.
The most useful video about Baxi boiler on RUclips. Thanks a lot. The relay in the middle of the board is indeed responsble for the fan. The other one operates the water pump. Cheap relays are from the Chinese on eBay. Cheapest UK I found was £4.
Hi. I had the same fault with the same boiler. The plumber replaced the pcb board with a brand new one. However, when i switch the heating on the flame stays on for about 5mins then goes off for a few mins then comes back on. The radiators are not even getting hot because of this intermittent on and off of the flame. Any ideas anyone???
Overheat thermostat?
What's the part name please
When you change your pcb on the baxi boilers some some.of them have the dip switch number 5 if off your setpoint will be 35°C to 85°C, but if the dip switch on the setpoint will be 35°C to 45°C causing your boiler switching on and off every 5 minutes and temperatures not reaching higher than 45°C.
Hi. I have a baxi luna combination boiler. In the summer when the ac is on and I take hot shower, only hot air blows out. Do you know a cause or fix for this problem? Need help!
Hi Niebko, there are 2 relays both the same, replace 1 if the pcb has the same problem replace the other one. These two relays are 90% of the boards problem. Available online very cheaply.Hope that helps.
dick smith thanks for let me know so quick.I replaced both relays for the brand new ones that I bought on eBay then reset boiler but red light 50 degrees still flashing and boiler won’t start up,pump running.Have u any idea what else maybe wrong with my boiler thanks
If you don't have new relay you can open up old and just clean them with deoxy 2:51
Hi is this Relay marked up RL3 ? My PCB is slightly different and I notice that there’s 2 the same relays on PCB I don’t want to make a mistake please let me know thanks a million
how did you diagnose the relay.. more exactly.. you removed it? how did you traced it? so that you know what is the component.
Hi, can you please tell me where I can buy the relay from
EBay