- Видео 6
- Просмотров 170 107
Valsted Makes
Норвегия
Добавлен 9 сен 2020
Hi and welcome.
My name is Michael and on this channel, I share just about everything I do in making, inventing, and in my different hobbies.
I hope you will be inspired.
My name is Michael and on this channel, I share just about everything I do in making, inventing, and in my different hobbies.
I hope you will be inspired.
Horn location and replacement for Ducato/Jumper/Boxer/Relay/ProMaster X250.
How I replaced the signal horn on my Fiat Ducato X250 from 2010.
I used the following torque settings:
Everything = hand-tight (max 12 Nm)
Connect with me on Instagram: valsted.makes
▬▬▬ Contents of this video ▬▬▬
0:00 - Intro
0:08 - Horn location.
0:22 - Removal
0:36 - Modifying the new horn to use original connector
1:09 - Removing the RH headlight unit
1:53 - Test install and function test
2:04 - Installing the new horn
2:24 - Reinstalling the headlight unit
#fiat #ducato #campervan #jumper #Boxer #Relay #ProMaster #X250 #vanlife #mechanics #horn #signal #headlight
I used the following torque settings:
Everything = hand-tight (max 12 Nm)
Connect with me on Instagram: valsted.makes
▬▬▬ Contents of this video ▬▬▬
0:00 - Intro
0:08 - Horn location.
0:22 - Removal
0:36 - Modifying the new horn to use original connector
1:09 - Removing the RH headlight unit
1:53 - Test install and function test
2:04 - Installing the new horn
2:24 - Reinstalling the headlight unit
#fiat #ducato #campervan #jumper #Boxer #Relay #ProMaster #X250 #vanlife #mechanics #horn #signal #headlight
Просмотров: 12 560
Видео
Solved the DJI Mini 2 Battery Issue with a little spacer. (DJI fixed it but its still useful.)
Просмотров 8 тыс.3 года назад
Remark the latest battery firmware update fixed the storing problem. Personally I still use it to ensure the batteries only is connected to the charger when I want them to. Solving the DJI Mini 2 battery storing problem which happens when using the charging hub to store the batteries. DJI´s intelligent batteries automatically discharge to storage voltage to reduce degradation of the lithium cel...
STEALTH SOLAR for Ducato/Jumper/Boxer/Relay/ProMaster X250 - CABLES THROUGH BRAKE LIGHT
Просмотров 9093 года назад
This video shows the best solution I could come up with for installing solar panels on our stealth Fiat Ducato L3H2 campervan, without drilling holes in the roof or any metal, and still make room for doubling the panel wattage later. This solution will work on all Ducato, Jumper, Boxer, Relay, and ProMaster X250 with brake light assembly. ▬▬▬ Components used in this build. ▬▬▬ Solar panels: Two...
Handbrake fix and adjustment for Ducato/Jumper/Boxer/Relay/ProMaster X250.
Просмотров 147 тыс.3 года назад
How I replaced and adjusted the rear handbrake/parking brake drum brake shoes inside rear disc on my Fiat Ducato X250 from 2010, and how I made a perfect tight adjustment to gain back the braking power necessary for parking on slopes. I used the following torque settings: Brake disc to wheel hub = hand-tight (max 12 Nm) Brake caliper yoke to car = 210 Nm (Bolt size M16) Brake caliper to guide p...
Making a vertical leather wallet
Просмотров 964 года назад
I love using this rugged vertical wallet. The front pocket makes one-handed operation possible, and the corners are pointy enough to press on touchscreens and keyboards at the grocery store. I filmed making another one, and I hope you will find it entertaining, and maybe inspire you to make one yourself. The drawings and 3D printable templates are available through www.valsted.no and valstedlea...
Glad to see it was not only me that struggled with those springs,very poor design
Far to dark to see anything.
Great Video lad! No blah, blah. As a carpenter I do what I can on my Citroen Relay Van to save costs. Much appreciated 🙏
Anyone here have recommendations for under vehicle rust proofing? I'm looking at lanoguard as an option.
Awesome video buddy like the tidy workflow.
ΦΙΛΕ ΝΑ ΕΙΣΑΙ ΚΑΛΑ ΕΥΧΑΡΙΣΤΩ
Ну наконец, я увидел толковое видео, где всё хорошо видно и подробно! Автору Большое спасибо и успехов!!!!
Esse sistema serve para Ducato ano 2000?
Зрозуміло, супер
I love the torque adjustment on the handbrake cable. I've never seen it done like that. Is that per manual?
Why did you remove the headlight?
Ďakujem pekne...prajem pekný deň
Are the filler pieces 3D printed?
Hi. Sorry for the late reply. Yes. The fillers are 3D printed
Nice. Thanks
At the beginning he states he is not a certified mechanic, i would to say he has a professional work method and certainly knows what he is doing. Nice to see a bit of H&S with the vehicle supported on axle stands. The last guy i saw doing this job was just working off the trolley jack accident waiting to happen.
Thanks for your comment. I’m an aircraft mechanic. 😉
Great video, simply step by step guide, thx
Top marks!
I did everything in this video and then replaced the cables, I can still pull away at idle in third gear. Took it all apart and redid it. Same. Do you have to use Fiat Original parts or are Bosch ok.
Hi. If you can pull away with rotation wheels you have adjusted the brakes wrong. Mine is locked, but they need to be adjusted regularly. I don’t use original parts but as good as
After you do this, if you have light rear side of the car, like tent, there are no enougth strengh in brake mechanism. Stupid construction actualy
I agree. Bad system, but a solid brake is possible. But you need to adjust regularly
Did exactly the same. There are no enougth strength to pass through technical inspection in Lithuania
I got the same sh.... van I have pun new brake shoe and discs. but handbrake when is going forward 😕 don't hold. in reverse they are solid
Have you fixed this? I have the same problem.
I agree with you, it’s a bad system, but great solid brake power is possible. The mechanical brake pad actuator, the one the cable is attached to must turn smoothly. I need to lubricate them to go through my last check.
Sprüh das Auto mal mit Öl ein, sonst rostet der noch mehr
Thanks it helped a lot, specialy with adjusting the brakes.
Can’t get the rotor on the right side everything is in properly, mirrored left side any ideas?
Your a life saver 👍
thank you so much
This is one of the best videos I have ever seen! As a mechanic myself, this gentleman did a fantastic and thorough job, and the best part of this video is the fact that he didn't bloviate and blabber in the beginning in the middle and during the video! All of you other RUclipsrs that make videos, pay attention! Nobody likes to hear 10 minutes about your personal crap or all the nonsense during the video, the best part of this was there was no talking!
Thank you for your kind words.
Thank you! Great from France
Thank you so much for the effort you have gone to in making this video, it’s so helpful and clear! Exactly what I needed. Happy travels! 🤙
Thank you. I’m happy you find it usefull
The spring clips that took you 2 hours can also be installed in 2 minutes! Clamp a thin self-locking hose clamp around it, compress the clamp spring using a water pump pliers, tighten the self-locking hose and then put it in place with needle nose pliers!
What do you do at 17:17 if it doesn’t sit fully down? Thanks
Adjust the cable from the handle to the link.
Visually really clear, great vid 👍
Cracking video. Very concise and well done.
Super gut, vielen Dank fürs zeigen. Grüße aus Deutschland
Thank you for this excellent video. I now have a good working handbrake.
What about the 2nd horn, that was hi horn there a lo horn as well
Great video thanks👍, I took the hub off and cleaned and re-greased the bearings, found it easier to fit the shoes back in that way as well 😄
Excelente. O criador do vídeo esta de parabéns !!
Grata pelas suas palavras. Tenha um bom veräo. (Google Translated)
This video saved me a fortune ! Took it to one garage 3 times & they still didn't get it right. Had it booked in somewhere else but did it myself after watching your video. Garage I was booked in with said, yhey have mechanics often coming in for them to fo it because they can't ! 😂😂😂😂😂 Thank you brother 👍
It sounds good. Thank you for your story. Have a great summer.
Great video, and easy to understand with all information needed I will be doing my motorhomes brakes this weekend ready for mot.
Num referenc for breaks?
Try putting year in description ffs
Hi Robert. To my understanding this system is very universal in the X250 series. If you can enligt me you are very welcome and I will add it to help others. Thanks in advance.
Nice rubyred colour od your van👍
Just pull the batteries out, turn 180° then put them back in. They only go in half way.
Outstanding information. All I needed to know as I embark on my own promaster break adventure! 👏 Thank you 😊
tq
Super sk
Thanks, very good idea, I will download the stl file and I did give a like on Thingiverse.
Thank you.
Super fin video. Jeg har netop lavet samme job, dog satte jeg nye skiver og klodser på ved lejligheden. Jeg havde det problem, at jeg næsten ikke kunne får skiven/tromlen af den i den ene førsteside jeg arbejde på, det var selvfølge fordi jeg ikke kunne finde den lille skruemekanisme inde i bolthullerne, så jeg hamrede og bankede på skive til den alligevel gav slip og kom af. Nu var problemet, at pludselig lå der i bunden af tromlen, de to små "pinde", dem der sidder med en clips. Jeg kunne ikke se mig ud af hvor de skulle sidde (da jeg ikke havde set din video). Jeg tog chancen og samlede det hele og fixede den anden side uden problemer. Nu er mit spørgsmål så til dig ;-) Hvad gør de to pinde og clipsen? Jeg har været ude og vende i bilen, men jeg mærker, eller hører intet forkert.
Det passer så ikke, at jeg gjorde samme job, da jeg jo ikke skiftede håndbremsebakkerne, men de ander bakker og som sagt skiverne ;-)
Hej Tony. Som du nu har opdaget er det vigtigt at få flyttet bremsebakkerne fri af tromlen, ved at justere på justeringshjulet og løsne kablet. Bakkerne slider en bane inde i tromlen, og den inderste kant bliver et step du kommer til at skulle overvinde, særligt hvis kablet heller ikke er løsnet. Resultatet er at tromlen hiver bakkerne med ud nå pindene giver efter. Pindene sikre at bakkerne holdes ind til bagpladen og bakkernes styr, er der ingen pinde vil bakkerne kunne “flyde” sidelæns inden i tromlen hvilket formentligt vil resultere i uens bremseeffekt på højre og venstre side, måske ikke nu men på sigt. Jeg vil ikke mene at der er plads til de kan vælte eller glide af deres styr, men jeg vil rette det snarrest, inden tromlen bliver slidt mystisk.
Jeg vil altid skifte bakker samtidig med tromlen. De gamle bakker er slidt efter den gamle tromle. Lad os sige den gamle tromle er slidt 1 mm ned i materialet, altså den har fået 1 mm større radius end originalt, den radius har de gamle bremsebakke så også fået. Når du så sætter en ny ikke slidt tromle på med mindre radius, vil de gamle bakker kun få kontakt på de to yderste kanter set ind på dem fra siden af bilen. Bakkerne vil måske blive slidt til efter meget brug, men du vil have dårlig bremsekraft indtil da. Bemærk det samme gælder ikke for skivebremserne da du her har en plade (skive) der bliver presset på af to andre plader, som iøvrigt er selvjusterende.
Og så lige en sidste ting. Jeg har lige haft min igennem syn. Bremserne var, efter min mening perfekt justeret, med fuldstændig ens bremsekraft og låste hjulet ved allerede første klik, testet med foden imens bilen var løftet som i videoen, og jeg kunne trække to end bremsespor i gruset ved tredje klik. Men synsmanden så 49% forskellig bremsekraft i deres teststand. Det viste sig at det venstre bagerste kabel var dårlig. Nu er begge skiftet og alt et godt.
Good video , wish I’d seen this before I helped change shoes and pads on my friends duke .. nightmare getting carrier bolts out as they had been loctited ! Just out of interest any idea what socket / torx is the shock absorber bolts ? Cannot find any information about them .. thanks for easy to follow video..
Thank you. I can check tomorrow. I'm editing front spring replacement, horn replacement and gear oil change in these days, so new videos is in the making.
Hi again. Sorry my late reply. I think the external torx is a E24, the biggest I have is a E20, and it won’t fit. Point to point distance is 21.4 mm on the bolt. In a hurry or a Sunday I will try using a 19 mm Hex socket, it fits snugly.
Thanks for your advice.. I will try measuring and see how it goes...