Видео

Email id pls

You are Gem

How can we get excel

is their anyone who can help me out for the installation of etap

sir can you please post the link of the video where you have detailed the concept of trip device in low voltage circuit breaker?

Sir, i sent mail query. Please reply

This channel is very extraordinary in explaining, good content also for someone who is still a beginner. he kindly also shared the entire file on this video. hopefully fast growing and successful your youtube channel. PLZ make more useful video and manual calculation (ETAP) SOFTWARE THANKS

Is there any way to simulate Transient voltage recovery after Generator fault clearance?

Lighting loads or sockets which may or may not be connected to motor shall be considered as static load?

very nice explained with perfect calculation plz make more etap videos with your projects and also share all excel sheets

Hi , what about the min. gap conductors/phases. And min gap conductors (L-G). Please clarify how we can get the above info

Kind of pointless video. Why not explain the reasons for selecting the values you did ? You didn’t explain the pickup range values, curve type, or how to coordinate with existing data.

Your english is so frightened that I can hear nothing。。。。。。。。。。。

Sir is there any possibilities to run 2 synchronous generators in parallel and connect it to a common bus ?

Sir Transformer impedance changes with tape position , how to adjust that in etap?

What fuckn you eating while talking, i lose my temper

I tried this in my system but when i give fault in bus 4 , relay 3 works first hence cb3 opens then cb4 then cb1 and cb2 Can u tell me where i might have went wrong i did the same as urs

are you litterly eating an lollipop while talking ? or what the fuck you sucking on?

Can you send the simulation of this circuit or can you tell where is the video of this simulation because i have to make it for my lab but clearly not understand what components you have used?

THANKS MAN! DO YOU HAVE DONE ANY VIDEOS ABOUT HOW TO GREAT DIFFERENT SCENARIO IOS OF THE SAM DIAGRAM ?

Its must to but pro version of dailux evo to get these features?

please am a beginner in dialux evo , Calculation problem Greetings, Awhen I press calculation, nothing happens. I can see the progress bars but there's no progress. I've waited for a few hours and still nothing. When I press cancel the calculation, I get "not responding" error and have to force it to close the program. I've tried to close and restart my computer multiple times, tried to do the calculations with my old work, also tried to reinstall dialux and made sure that the computer is updated correctly, but nothing seems to be working.

Hi sir. How to input leading power factor value at generator sincron on etap. Thanks

Thank you, Could I get a copy of the spreadsheet.

Just dont click everywhere randomly and trash talk. Just give an introduction initially what is the aim and what are you upto... After 3:50 minutes complete trash talk and ahhmmm ahhhmmm and random clicks.

I love you. Thank you so much!

Good day sir, I have a question. For example, how can I write a 34.5/0.4 +_12%1.25 transformer into the program? That is, where should I write the +-12% 1.25 values? And where should I write the losses?

Hi Sir, what could be the reason if the "FCT not determined" error still showing against ACB even when the trip device is selected? Please support, Thanks.

When I place a fault on any of the downstream busses, it opens the HV CB. It should technically? Thanks.

why did you set the secondary pickup to 170 amps ?? i don't get it ?

Ive just worked the calculation for volt drop at 1.777 and not 4 any ideas what ive done wrong could you show the calculation format in the cell

Hi, Thanks a lot for the info, Greetings from Colombia.

Please can you share the excel sheet. thanks

Sir, usually for earth mat design we consider soil resistivity data at depth or spacing of 10meter for determining soil model. What should be the depth or spacing at which resistivity data should be considered please guide and also tell if there are any references in IEEE, for the same. Thanks

Is there any way to clip the current and see more than that current in the curve? I'd like to see the entire curve and the SC levels in one plot without having to add manually the current levels

Why don't discuss the dump load model editor..

Please make one video related to support for the Tray routing and Control room cable tray routing? Expect positive reply

This question for both electrical and Instrumentation team

Hi sir, thanks for the valuable video, Should we give a separate Cutout or Wall opening details layout to the Civil team?, or else after we model they take it from Navis.

How to calculate the fux level for particular room

Why iam always error

Wonderful job my man!

Thanks 👍

I have doubt in following points ..kindly explain 1. Calculated Vk as per given data is coming 175 V. then why you consider 175 V as Vk/2 and 350V as Vk?? 2. In calculation of stabilizing resistor, Formula given in Vs and you consider vk 175 V in place of Vk??

AUN CUANDO CAMBIO LA PRECISION A 0.9 NO PUEDE GENERAR LA ESTIMACION MIENTRAS ESTE EN NAMEPLATE, EN TANTO QUE CUANDO LO CAMBIO A USER DEFINED SI HACE LA ESTIMACION

could you provide excel sheet??

thanks man but! isn't Solid grounding less common in LV systems?? due to the high fault currents it produces, which can lead to equipment damage, arc flash hazards, isn't, resistance grounding or ungrounded systems are often used to limit fault current, enhance safety ??