Видео

Mine doesn’t wanna turn the blade at all and it’s brand new

Thank you!

Recheck the oil level after running it. The filter will fill, and the oil level in the engine will be slightly lower. It shouldn't be a lot because the filter is small, but why not get the oil level up to full.

Extremely helpful

Hi, I have the same mower/engine, when I use the taller filters (Fram PH7575 0r 3614 or equivalents) the steering rod rubs/dents the filter when the left front axle goes upwards on hills or bumps, I can see in your video you don't have much clearance left with the taller Fram, the dealer told me they are well aware of this issue and that is why they went with the shorter filter (Kohler 12 050 01)

Excellent review Sir!! Just picked one up today and now need to order up the plunge base. Thank you!!

Nicely done John!!

You did not mention how much it weighs, or costs?

Great video! I have an issue with my front wheels going in different directions and it's difficult to steer. Any recommendations on how to fix that? My mower is very similar to the one in this video

I need this! The change oil notification just came on.

The W stands for winter, not weight. And with it being multi viscosity, it'll have the lubricity of 5 weight in cold temps and 30 weight in hotter temps. Just trying to help in case someone didn't know 👍🏻

What model Delta dust collector is that? Is the suction better or worse after the mods? Usually the filter helps improve suction but the cyclone usually reduces it.

Thank you! Very helpful.

Everyone online in recent years are complaining about the blades, how they are only good for a few cuts even in easy stuff like EMT, the weld snapping, blade teeth burning out, etc. How are your blades holding up?

Underrated channel, keep up the great work! 😊

First, use some cardboard, don’t mess up your garage floor. Then oil on the ground everywhere. Hahahaha. Just kidding. Thanks for the informative educative video clip. It helps a lot!

This is pretty close to what I have in mind for my garage. Cool to see how you did it

Did you ever take a measurement of the saw's height after installing the mobility wheels?

Great build out. Getting ready to set up my garage shop again after moving it from CO to TX.

would this have the power to, with the proper blade, to cut lets say 3/4in or 1in black iron pipe?

Thank you this is exactly what I needed!

I'm running mine off a compact 21700 based 4Ah DeWalt battery with adaptor and can still fit my fingers through around the top handle. I also have M18 nail guns and Makita Jap made grease gun since DeWalt dropped the ball on all of those.

Also for the people looking at this video, look at the Kreg acu cut system. I used the system for awhile and was very happy with it, not perfect and does have a bit of play but it worked very well.

So just a tip I couldn’t see much of a gap between your guid rails. The consensus is you should leave a 1/8 inch gap between the two guides because they are not machined perfectly 90 on the ends.. that’s what I have heard.. I bought the saw with a 8.0 amp battery like you. I’m just waiting to get my guide now boy are those expensive

how did you setup your packout for the saw?

I need to know which battery to purchase for the DCCS670 chainsaw. I bought a used on and it did not have the battery. Is there a particular battery model or sku to use with this chainsaw

Really looking good

4:36

Nice work! This looks great, and I appreciate that you used practical materials that look equally as good as the youtube go to of Baltic Birch!

Beautiful looking cabinets, John. Nice work!

your definition of "easy" is different than everyone else's. good video.

Very good demonstration

Hello, where exactly do you check about other filter fitment? Normally places like Walmart doesn't let me select Lawn Mower as a vehicle in order to check about fitment. Is there any certain website where you go to check that?

Thank you for the video.

I disagree the problem with the Milwaukee dolly is that the wheel brackets stick out to far , which stops tidy packing in the van and on the job site. So for me it was not about the money . I have been using my DIY versions for the a good while now coupled with a costco sack truck which gives much better versatility. So DIY has been the way to go for me.

Thanks for making this video - well done! I have been looking at the 14bx for a couple of years now and getting close to making the purchase.

I wish i had need for a tool like that.

Lovely build.

quite a quality video 👍

Great video, in-depth, informative, and easy to follow. I’ve seen several french cleat videos and this is one of the best. I’m moving into a new shop soon and it will have some cleats on at least one wall.

Exellent video

I didnt realize those holes allowed a piece of wood to extend but can you also flip it upside down and use against a raised surface instead? I also thought you couldnt use track guide at the same time as the vac attachment but it looks like it does work with the regular guide? What's the deepest plunge and routing that can be achieved with this tool, I think someone said 1 & 3/8 but what if I need 2-3"? Great review thanks!

Thanks. What is the 45 degree PVC with nothing connected right by the black collector barrel?

I just got one and got lucky with the whole caster placement i used common sense and figured id be out front most the time and if im hittin that brake pedal i may apply the parking brake at sum point so i luckly put the lockers on the front anyway to my surprise it worked out in my favor lol

Thanks for the detailed rundown. I definitely hit the subscribe button after such a great job! 👏👏👏

Great details. Thanks for all the valuable information.

Очень понравилось освещение на заднем фоне, камера четкая детали все четко видно Спасибо!

Howdie awesome workmanship I joined cause you got this and ya dont have to be a rocket scientist to understand what you're saying so keep up the ideas coming mighty fine Sir thanks for sharing your ideas with us can ya make a cleat holder for Bolt cutters mine are 22 24 26 long and all are 4 and half wide ther big ones for my fence cutting use them alot so hopefully you have some ideas from Canada 🇨🇦 SK later thanks again Paul 😊

Like to see an all terrain wheel replacement modification to the dolly

Another good video, John. Keep it up!