- Видео 59
- Просмотров 23 417
Golf Cource Mechanic
Добавлен 24 авг 2016
Small engine repairs
Kubota MX 5100 steering pump replacement
This job was not to bad #golfcourselife #golfcoursemaintenance #mechanicshop #mechaniclife #repair #smallengine #smallenginemechanic #smallenginerepair #mechanic #kubota
Просмотров: 10
Видео
Kioti tractor dying after running 
Просмотров 67Месяц назад
Check on the simple stuff first #golfcoursemaintenance #golfcourselife #mechanic #mechaniclife #repair #smallengine #smallenginemechanic #smallenginerepair #smallyoutuber #mechanicshop #kiotitractor 
2013 clubcar ds won’t run just idles
Просмотров 1 тыс.2 месяца назад
This is the first thing you got to check #golfcoursemaintenance #golfcourselife #mechanic #mechaniclife #repair #smallengine #smallenginemechanic #smallenginerepair #smallyoutuber #mechanicshop #clubcar #golfcarts #golfcart
Toro rotting egg smell?
Просмотров 5602 месяца назад
Voltage regulator is cooked #golfcoursemaintenance #golfcourselife #mechanic #mechaniclife #repair #smallengine #smallenginemechanic #smallenginerepair #smallyoutuber #mechanicshop #toro
husqvarna chainsaw issues
Просмотров 6852 месяца назад
Quick little fix on this husqvarna saw #golfcoursemaintenance #golfcourselife #mechanic #mechaniclife #repair #smallengine #smallenginemechanic #smallenginerepair #smallyoutuber #mechanicshop #chainsaw #husqvarna #husqvarnapower
How to fix a spark plug with no thread chaser
Просмотров 3862 месяца назад
How to fix a spark plug with no thread chaser
Toro mdx wheel bearing and brake service 
Просмотров 802 месяца назад
Toro mdx wheel bearing and brake service 
Reel master 5410 main hydraulic pump failure
Просмотров 785 месяцев назад
Reel master 5410 main hydraulic pump failure
Nightmare hydraulic line on Kubota tractor
Просмотров 775 месяцев назад
Nightmare hydraulic line on Kubota tractor
Reel replacement on a toro 5410 fairway mower
Просмотров 1625 месяцев назад
Reel replacement on a toro 5410 fairway mower
How to replace crank seal and gasket on clubcar ds
Просмотров 1415 месяцев назад
How to replace crank seal and gasket on clubcar ds
How to replace brushes on fairway mower
Просмотров 985 месяцев назад
How to replace brushes on fairway mower
Rollers off a ventrac rebuild mower deck
Просмотров 1056 месяцев назад
Rollers off a ventrac rebuild mower deck
I feel you
That's the first thing i would have checked .😮
@@stevegriffith7236 first time I seen this happen with the linkage falling off alway see the foot pedal switch go tho
I was at the GCSAA Show years ago and I met a Clubcar Engineer. I asked why they put those crap Clubcar carburetors on these Kawasaki engines. He admitted that that they were junk. If you want to see these engines run GREAT, take the model/spec # and get a Kawasaki carburetor.
Forsure not that bad to do
I have the same problem but I have gas I change solenoid voltage regulator and belt it moves a little and then stops I think I could be primary clutch or the second but not sure do you have some advice
Check the vent on top of the engine little hose that goes from the top of the engine to the carb might be gum up. The other thing to check is try starting with a fuel cap off might be vacuum locked.
@@golfcourcemechanic4834 than you I will try this and see if I can make it run
I have the same problem but I have gas I change solenoid voltage regulator and belt it moves a little and then stops I think I could be primary clutch or the second but not sure do you have some advice
Correct,, if ur plug ain’t winding in easily with yr fingers, don’t persist, take it out wire brush the thread spray lube it & try again with yr fingers only, it should wind down 95% of the way with ease, then u know you’ve got it right . Wasting 2 minutes at that stage is FAR better than cross threading it.
100%
I have this same job coming up. I think I'd first degrease and wash all the crud off before getting into that repair.
Not so much how to sharpen the blade but rather a vague description on how to balance one. Well done.
I was hoping to see you actually sharpen. I bought a bench grinder just for sharpening blades, but I'm not very good at it. I could get it sharp (maybe too sharp) but would take off too much metal, then even more trying to balance. One day I just put a blade in a vise and used a file, and realized that's probably how I should have been doing it all along. It would be nice to see a pro do it right,
Change the voltage regulator
lol did you watch the whole video
great video about grinding reel mowers. please more of them!!
Where’s the oil filter on these ?
I have a question for you. I realize that you can't answer everyone's questions, but I have nothing to lose by asking. I am working on a fiends Club Car. Nothing happens when pressing the pedal. You don't even hear a click. The solenoid has tested good, also if I just the solenoid the cart will start. Fuses are also good. I can't find the control box on this machine to find out if the micro switch is bad. Do you have any idea where I should look to find the switches? I know about the direction micro switches. What should I try next? I would appreciate any help you could give me for this