Видео

So it slips over the plastic part of the "smaller" spools which is the same diameter of the oe spools so you don't need to swap them.

Will these fit a 2022 softail street bob?

Do these fit the Lowrider FXLR?

How about a wiring diagram for the 5 pin 2013 tour pack

I don't understand why nobody makes a solo luggage rack for Harley touring models. Especially now that there are all kinds of detachable setups. Something to think about.

Just bought them, I’m excited to install them out of curiosity

Will this fit on a 2021 sportster iron 1200ns?

For 25 years on my 2000 Police Road King , I didn't know that those clips are pushed below the Grommets. I've always left them above them.

Are these factory length or they 14 in or what are they?

💪🏾💪🏾💪🏾💪🏾💪🏾💪🏾

Can i fit a LP6 on it?

Have anybody bought and tested them already need to know before buying?

What’s the price

I can't decide if I want speakers or glove box!?!?!?!? Leaning towards glove box.

I got a 4xl in this model. Will this be good for street bob with real bars

Leave your motorcycle and i will lift those hinges and steal your sissybar back rest....😅...to prevent it remove the saddlebags and put two screws on the two sides locking those hinges 😊... Then put the saddlebags back and your sissybar is safe

I couldn’t tell from the video, but do these interfere with passenger foot pegs, or do these mount to the other hole without issue?

Any plans for conversion brackets for Dyna? 2001 Superglide to be more specific.

So. Am understanding with this setup, you cant put your tourpak back on??

The inside thickness is slightly thinner. However they are still amazing bars. They will 100% get the job done. For a 4th of the cost.

Can this be done another way with the fairing already installed on the bike?

Bike almost went down yesterday due to a massive pothole right at the base of a switchback curve/turn on a mountain road that required extremely slow speed. Buying these today.

I need mid controls for my 02 twin cam fat boy. Cannot locate them anywhere.😢😢😢😢

I am installing my new fender and I am missing the screw that attached to the fender bracket.

Where is the installation video for the wire harness

Does anyone know the measurement from bolt to bolt center that mount to the fender thanks

Can i get just the outer fairing? I only see inner and outer fairing.

@JustGKue how do i get intouch with them im trying to order from them and the website says it doesn’t deliver to my address and i tried 3 other addresses. I tried email no response. Any help will be appreciated thanks

How did you connect the air pressure regulator on the tank into the system

You could have at least have made them the same size.

Will they fit 03 dyna

I ordered a set from Amazon and one from during my trip. My club brother had the same ones, and his broke too during the very next trip…

What size are the bolts under seat?

They sure do not coexist with saddlebag guards if you decide to use your existing guards or order guards later

Thank you for your help. 😊

How to carry them when you need to unfasten them from the bike?

What size are the bolts under the seat

👍👍👍👍

do your shop have a rear turn signal reloctaion kit?

Make these for a sportster?

Use a good metal plate

Yeah you'll find out

The clips and slides in jog workx is totally better the Amazon the tour pack with chatter around a lot bro

It's not it's crap I had one it's looks good but hog workx is much better

, they smoking something good in northern ca

this bike doesn't have tcs?

Hi I’m trying this on vrod. I bought wiring harness from tcmt. Can you share how the rear led and marker lights are connected to harness and what the output of harness should be

I just bought a fender with the extention like the one in this video and the plastic fender was to thick for the seat screw hard ware I couldn't get the clip on the top side of the fender so I could screw my seat down I had to drill out the hole and then get a grinder on the inside so it was thinner

Only thing Ive noticed is on mine compared to other OEM is that gap in the back of the seat. you can almost stick a finger in it. compared to OEM its a lot more flush. I wonder why that is?

I enjoyed the review with oem and knock off side by side. I thought you did a great job comparing the two. Thanks for your time and effort. Mark from Maryland