Видео

Hey i have a 1994 kawasaki xi 750 ss and in the water it wont rew over 5.5k.rpms. on the trailer it rews just fine and all. As soon as it hits water it cant go.over 5.5k. do yoi know something about that?

Yea dont show the most important part

Thanks! Good video!

Kip

Just wrapped this job up on my leaky heater core. This saved me so many hours, to seal up the cuts i just used ole mexican chrome tape :) Great write up man! TY

I would hire your boys and pay them $30 an hour each. Great job on guiding your kids on the right path 🙏🏽 Thanks for sharing this!

Great video , to the point, you made aware of what to look out for, I will be taking on the exact same job, great video

Will this work on a 98 xj?? Man, i do not want to disconnect my AC it blows colder than my 2019 tacoma or my 2015 optima. LOL

あなたのおかげで修理出来ました。 ありがとう😊 750sxi pro

was there no spacers that went over that small sleeve you installed between the grease seals? ive gotta rebuild my 550sx pump and its real similar

Hello Dan, where can i get the bearings? Greetings from germany

Been drowning my passengers in coolant. Going to try this, sounds like I need a new heater core.

Genius, thank you

Berapa harganya nya itu bos 1 set

Cool video loose the music an explain how to use it on start up

Liked your video- great idea. One question though, if you can install the new core without damaging the tubes, can you not then remove the old core without cutting the tubes? Or did you just cut them to make removal easier? Thanks

Ok

Thanks for video.. been putting this off for yesrs and my mom has suffered every winter without heat.. This looks easier and epoxy should keep that plastic together just fine

👍💯❤

ok..

Gud day boss saan Po ba nakkabili nyan

There should be a hell of a lot more great comments... your boys look absolutely competent... 😇😇❤

WTF

FYI the drive shaft can be used to remove the impeller. So there's no need for the special tool unless you just want one.

I think I'll use a dremal

I like it I might just cut hole in dash....

Cimer cousin

I want to buy jet ski thruster from you

The dash is the biggest choir. Once that’s out ya May as well pull heater box as well. Only few more bolts.

Nice

Just saved me so much work, thank you!!!

You don't have to remove the center console ??? And what about steering

Awesome job guys!

hello, is it possible to do some minor repairs by welding the duct or the propeller? Thank you

por que monta los retenes al reves

I already took it all apart. But im gonna give this cheat a shot to get old one out and new one in.

I've had this lathe for about 5 months and loved it until the handwheel and lead screw came undone and I cannot get it back to working properly. Any time I try and drill a pen blank, the handwheel and lead screw unscrew instead of boring a hole into the pen blank. Any pressure against the tailstock causes the handwheel and lead screw to come out instead of drilling a hole into the wooden pen blank. Any suggestions? I tried calling support for technatool and they tried to help but really hard to do over the phone.

I really like it. Also check out Woodglut and plans.

Ive got a 750 sts , where can i buy the impeller removal tool

Its been a minute since you posted this but Man Im glad you did! Ill be “going in” this week. 👍🤘🍺

Hey how is your lathe holding up? Have you had any problems?

Father help son😁🙏🇮🇳💯 Love from India 👍🙏

Bravo

Thanks Dan... I'm not a mechanic by any means but I do try to repair anything that I can do myself. You saved me so much work and alot of complaints from my neighbors for alot of cussing..lol thanks again.

Good work. But I think those kids are underaged for this activity.

Cherry oakyyy? Lmao

Come check out our new channel for Montana's Lost Art ruclips.net/channel/UChN2qZ98hLVRX3Cmu23GLrg

Come check out our new channel for Montana's Lost Art ruclips.net/channel/UChN2qZ98hLVRX3Cmu23GLrg

#sendit

This is one of those “other shop jobs”.