Видео

Jones Deborah Smith Melissa Thompson Barbara

Tessie Tunnel

Smith Frank Thompson Deborah Allen Linda

That only shows a single partition. It's Windows compatible, which is not the Linux disk format.

Looking for help here. While running the service, I am able to move around the setup page and even make new worlds, download systems and addons, etc. But when I attempt to a launch a world, it will throw a "Segmentation fault (core dumped)" error. Also, every time it does this or I launch it with docker compose, it completely regenerates the foundry options file Raspberry Pi 3 B, Raspbian 32 bit, most recent update of docker and raspbian, if there is any other information I should send lmk.

After getting the black screen, and choosing option 1, the installer completed and I never saw the blue screen install wizard. Does someone know why?

Hernandez William Thomas Melissa Thompson Eric

First of all, thank you!! Second of all, currently I am using a Sonoff Zigbee Anthenna for Zigbee2mqtt, together with Homebridge. I ran into a strange problem. If I try booting the system with the Anthenna on, it won't boot, however when I plug off the anthenna then try booting again, it works, then I can plug it later on. I think the system is not sure on which usb to boot so it gets stuck on booting, then if there is only the USB drive on it boots with no problems whatsoever. Do you have any ideas how may I fix this? Is there a way to set the system to boot from a specific USB port? If so, how could I do it, which commands? Thank you so much!

Why there ar personas using winrar. 7zip is free and opensource and also can open RAR too if you don't know? ohh wait is a paid advertised video!

It worked 🙂 THANK YOU!!!!!

is the device still running good and nice?

it takes 2 minutes on Windows to solve this problem... on rocky linux it took me ages and I ctill can't figure it out.... your should add troubleshooting at the end. I have problems with credential file it seems... and I cannot find a way around it

Your broken engrish is impressive.

Thanks, helps alot

Hi i tried to install pfsense on Vmware but its only giving option to set wan connection and doest giving option to set LAN Connection on lan option its only coming as "a" it should give option like you ie01 ie02 like that but it doesnt

Mine runs hot under 80degree in opnsense. I can barely touch it. Is this normal for a fanless PC?

Many thanks for the video. Very helpful. As a Windows user, I can't believe this is the way to connect a network share. This is a good example of why the normal computer user doesn't want to switch to Linux. It is a mess.

your video sucks nothing is showing on my system like you show this is fresh install that has nothing done to it. my dvd drive comes up as sr0 11:0 1 2k 0rom and where do you show that

Are you Tom Hardy brother?

I got an error at this command:sudo pip3 install docker-compose error: externally-managed-environment and no further installation of docker compose

genial

Hi, it didn´t work in orange pi zero 2w and the magisk version is 27... when i download it doesnt download a .bin file it just downloads a .zip but when i try to install it just crash and close the magisk app please help

Oh dear, I followed the first half, then got lost. I think this video is good for those who already know what everything means. Does anybody know of a youtube channel which teaches this stuff for new linux users?

So i attempted to create a image using these steps for firefly station m3 however it created multiple .deb files not an iso

Great video, but as you know if i have an ont fiber connected to this device with opnsense ofc setup ppoe, this device can do also as a wifi router itself? Thanks in advice

I like the way you described that sir, i’m subbing for more!

🎉❤

Thank you very much for this very informative vid.

Really good clip, sir. I like to think I stay pretty on top of things and I hadn't seen the non-free-firmware tip mentioned. I'll need to dig into that more. Also, most folks commonly post removing subscription hacks that no longer work on 8.x (as you mentioned) so was impressed there. Good work.

For me, logging out of the system and logging back in was freezing the OS. If this is happening to you, there are two solutions: 1. Be sure that right after zsh is installed, run the zsh command and use one of the options from the initial message that creates the necessary files (I usually use the 2). Then you can log out and log back again. 2. If you already logged out and got on the freezing situation, you can either reinstall the OS and follow the previous instructions, or, if you don't want to reinstall everything, run the OS demo on a flash drive you probably used to install and create the files there and move them to the correct user folder.

to those struggling with sudo vim /etc/systemd/timesyncd.conf you can simply replace vim with nano hope it helps anyone

You lost me at 1:02 , I turned on terminal , typed vim.smbcredentials & it said comand not found

Hi. I have an old 32 bit arm cpu phone. How I can create a bootable device with all drover?

Man, wow thx a lot 👊🏼

Thank you this has got to be the most helpful video and easiest way to backup the pi sd card. Backing up the raspberry pi sd card has got to be the most important task as well as restoring the image to the sd card. Im going to to do it with the Mac version.

I absolutely refuse to use a product called "Pi-Hole." Nerds need to calm down with this stuff.

What you think is better orange pi5 or raspberry pi5

great tutorial but "docker compose up - d " does not work!

i was so afarid of starting from scratch again.. liked and subscribed you saved me from hours of work

Win32 Disk Imager is a pain in the ass because it simply won't work if you have a mounted drive in your PC like Google Drive. I'm still searching for an alternative.

It looks like it works still fine. Thank you for the nice guide!

Just completed this series, needed a couple tweaks as some stuff has been updated but overall works great. Thankyou for this excellent series.

CNN ??? hahaha I want news, not lies.

Amazing! This is exactly what I was trying to figure out. Thanks you!

Wait, great tutorial but im lost as to which system you installed the pfsense into. Does it need to be a seperate device? must it only be a router type device? if so on router, how did you proc the screen and the router to react that way. I was hoping that would be showed at the very start of the video on where or what exactly you placed that flash drive into.

Hi - My USB mem Stick, Not showing up on the Desktop. So I tried the terminal command ( lsblk ) Mem Stick Still not showing in list. So tried ( lsusb ) and the USB mem stick shows as ( Bus 002 Device 017: ID 1e3d:198a Chipsbank Microelectronics Co., Ltd ) Now What do I do?

i understand everything except the 3:45 second mark. Where do i get my ip, gagteway and dns server?

I stumbled upon this video and I'm glad I did! My shares, while mounted and functional, the mount command was a bit different and it seemed like things lagged a bit. I followed these instructions and now my shares access seems so much faster and even restarting doesn't take a long time like it used to either. Great video!

Wellllll...I am using a Pi-Nas running OMV.. connects perfectly and instantly in Windows 10... but when I am trying to connect my Linux Mint LMDE 6 Faye machine, it is saying unable to CHDIR to my Nas directory. I >KNOW< my directory, I have tried caps and lower case, no avail. :(

Can for orangepi zero 2w...??