Видео

Gotta take care of moms!

Ooof the wheel damage. Got it done though 😅. For the future, removing or installing the tube tires shouldn’t take much effort. Looking at the tire top down as a circle, You want to move one half of the tire bead (where the tire meets the wheel) into the concave portion of the wheel (part of the wheel where the radius is smaller) This will allow you to shift the tire over and release the tension on the other side. You should now be able to use the tool with minimal effort to lift the bead over the wheel (instead of prying it over)Then just use your hands. No need for the metal tool either. 8:22

It is easier to get the tire on the wheel by lying the wheel on a piece of carpet or something and then taking both hands and kind of doing a push up down on the tire with the wheel on the ground. That is with soap and a heated tire it goes on easily.

New subscriber, enjoying your videos. I have a ruckus and motorcycles. Not trying to be a dad but unfortunately you need to ride in full motorcycle gear since you can't get away from cars. Tesla's don't have lidar and thier stupid autopilot detects the tiny brake light of a motorcycle/scooters as vehicle that's much further down the road. At stop signs, use your hands to signal cars to go as if you are a traffic conductor. Ride safe.

Hey, I just came from watching your manual transmission fluid change on your civic. How is it holding up?

Love it! Glad to see you posting again

A smaller Honda but still looks good. 👍🏾

Kept watching even after you gnarled the side tire reflector only to find it it wasnt for solid rubber tires and you just speed ran through the actual tire removing process .🫤

Please tell me where you got the mugen wing with the 3rd breaklight.

Stepping on a brake disc😬

I love your vids but please fix those headlights!!! Lol is super easy I had mines just the same, I bought some mothers rims polisher I grabbed my wireless drill and a little polisher sponge and 5 min later DONE! No sanding, no clear cote and my Leds now looks awesome. Cheers buddy keep the good job😊

This is the best tutorial out there, and most accurate to how it should be done. The only thing different is you don't have to remove the alternator, it was still easy to reach the bolts on the compressor and fish out.

Full compressor swap in 30-minutes, while explaining the process, very good job!!! …and you spent time at the beginning of the video explaining quotes you had got! Next level!

Any ideas on how to get my rear passenger door fixed? I'm not able to open or close it either inside or out 🫤

I replaced my ac compressor today using this video as reference. I didn’t have to take off the alternator though, there was plenty of room when you remove the radiator fan.

Hmm did you checked the condenser if it was oily? On my car was the condenser that was leaking refrigerant. And a condenser is cheaper than buying a whole compresor

Hmm I am guessing if the Goodyears Eagle F1 Assymmetric 6 are better tires than the Pilot Sports, at least I am sure they are a more all weather tires for sure😉

LMFAO Snapped mone off too, same side, same wheel and everything hahahaha

LOOKS NICE THE BEST ATTENTION TO DETAIL START BY CLEANING AND HAVING A WASH CAR AND VACCUM CLEAN CAR GOES A LONG WASH START THERE FIRST AND THOSE ARE REAL "👌🏼 CHEF KIZZES" GOODLUCK BOLTS & WASHERS LOOK KOOL 👍🏼

I honestly didn’t know this helps a lot thank you

That rx7 though

how about the shift boot? there is a gap there. dust my get inside the boot

Do you know anyone selling mugen civic fa5 body?

Thanks that help a lot I’m doing this for sure.

Extremely helpful video. Although I don't think you have much mechanical experience before this... good that you are trying.

why my high pressure port plugged up with a bolt

Do you feel any difference with this?

Im still trying to find a video on how to change the brake pads on my hover-1 pro boss r500

👏👏👏👏

Nice car I have 1 of a 1000

damn that trans fluid looks like water i know it wasnt but when you touched it, it looked lke water

Bro is that a hover 1 renegade

Best tutorial I’ve seen yet. Doing it today 💪

Finally! A proper video where its shown to have the car LEVEL ON 4 jacks stands to drain all the old fluid and advising to crack open the Fill bolt FIRST 😊 KUDOS dude! Regarding using Amsoil, doesn't it state on the bottle not to use it with an LSD which the Si has?

Great video thanks buddy I’ll be working on my car tomorrow I hope I do it right ❤, thanks By the way you asking for a mechanic., please find a good one a lot of them just focus on the money and do shittie work I brought my car to a mechanic to change front hubs bearings and fucked up one by replacing a bigger bearing in the knuckle, so just the knuckle it self costs 647 dollars that hurts so much ., Well good luck on finding a honest and good mechanic budd

Omg

One of simple and much needed mod. Happy see you back bro!! 👍

Looks good and congratulations on getting a new place. I'm looking forward to more content.

finally!!! been waiting for an upload. welcome back shank

Welcome back!

Thank you so much for showing me how tomorrow i can do it myself🙌🏾

could you link the amazon for the filter? thanks :)

I came in to see the Mugen Si, not to listen to you go on and on about your ex cars

With the bodykit and the official exhaust and wheels you should just try to keep everything. Like a mini Mugen RR.

Hey bro nice video, i have a question what brand and model rotors are those?

never put your donut spare at front on a front wheel drive car fam... just for safety.. always put them in the back, same with a rear wheel drive car, never put donut spare on the rear for a rwd cars... stay safe fam...

Looks great! I used to have a titanium knob in my s2k and had to carry a rag in my car so I didn't burn my hand on a hot day... just a thought

super informative. thanks

16mm? Um bro its a 17😂😂

That tip for removing the wheel turned this into a 2 hour job for me, and I'm a slacker. Thanks man 👊